CSA/ANSI NGV 4.3-2022
压缩天然气汽车燃料的温度补偿 本文件提供给 SCC 仅供非商业内部使用 为明确起见 不允许进一步复制或分发 转售是

Temperature compensation for compressed natural gas vehicle fuelling This document is provided to SCC for non-commercial, internal use only. For greater clarity, no further reproduction or distribution is permitted. Resale is

标准号

CSA/ANSI NGV 4.3-2022

发布

2022年

发布单位

SCC

当前最新

CSA/ANSI NGV 4.3-2022

 

 

代替标准

CSA/ANSI NGV 4.3:22

被代替标准

75.200

适用范围

1 Scope 1.1 Inclusions This Standard details the safety and performance requirements for temperature compensation control used to prevent compressed natural gas (CNG) dispensing systems from exceeding a safe fill level for vehicle fuel storage container(s). This Standard contains safety performance requirements for compressed natural gas fuelling dispenser temperature compensation systems. It applies to newly manufactured dispensing systems and the field evaluation of existing dispensing systems designed primarily to allow for full fill and to avoid over-pressurization of vehicle fuel storage containers under the operating temperature conditions as specified in this Standard. This Standard applies to CNG fuelling of vehicle containers with service pressures of a) P30 [20 700 kPa (3000 psi)]; b) P30HD [20 700 kPa (3000 psi)]; c) P36 [24 800 kPa (3600 psi)]; and d) P36HD [24 800 kPa (3600 psi)]. P30HD and P36HD are designations used in accordance with CSA/ANSI NGV 1, and throughout the document, the use of P30 and P36 are also applicable to P30HD and P36HD, respectively (see Annex A of this Standard regarding applicable vehicle service pressures). This Standard is applicable to the dispensing of only natural gas that meets quality and specifications contained in ASTM D8080. 1.2 Pressure references All references to pressure throughout this document are to be considered gauge pressures unless otherwise specified. 1.3 Quality and innovation Nothing in this Standard is to be considered in any way as indicating a measure of quality beyond compliance with the provisions it contains. It is designed to allow compliance of products that may exceed what is specified in the provisions herein. The requirements of this Standard are not intended to constrain innovation. In its preparation, full recognition has been given to possibilities of improvement through ingenuity of design. When considering fuel compositions, controls, materials, designs, or constructions not specifically dealt with in this Standard, these alternatives are to be evaluated as to their ability to yield levels of safety and performance equivalent to or better than those prescribed by this Standard. Note: This Standard is subject to revision as further experience and investigation show it is necessary and desirable. 1.4 Precedence Users of this Standard are advised that the devices, products, and activities within its scope might be subject to regulation at the federal, state, provincial, or local levels. Users are strongly urged to investigate this possibility through appropriate channels. In the case of a conflict between this Standard and federal, provincial, state, or local regulations, the governmental requirements take precedence. 1.5 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.6 Units of measurement All dimensions used in this Standard are in SI units, unless otherwise specified. If a value for a measurement, as given in this Standard, is followed by an equivalent value in other units, the first stated value is to be regarded as the specification. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, either the first stated unit, or both, are to be provided.

CSA/ANSI NGV 4.3-2022相似标准