EN 88-1:2022
燃气燃烧器和燃气器具的安全和控制装置 第1部分:入口压力不超过 50 kPa 的压力调节器

Safety and control devices for gas burners and gas burning appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa


标准号
EN 88-1:2022
发布
2022年
发布单位
欧洲标准化委员会
替代标准
EN 88-1:2022+A1:2023
当前最新
EN 88-1:2022+A1:2023
 
 
适用范围
EN 13611:2019, Clause 1 applies with the following modification and addition: Modification: The 1st paragraph of EN 13611:2019, Clause 1 is replaced by: This document specifies the safety, design, construction, and performance requirements and testing for pressure regulators and pneumatic gas/air ratio pressure regulators (zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure regulators) for burners and appliances burning one or more gaseous fuels, hereafter referred to as “pressure regulators”. This document is applicable to pressure regulators with declared maximum inlet pressures up to and including 50 kPa and of nominal connection sizes up to and including DN 250. Addition: This document is applicable to: - pressure regulators which use auxiliary energy; - pneumatic gas/air ratio pressure regulators, which function by controlling a gas outlet pressure in response to an air signal pressure, air signal differential pressure, and/or to a furnace pressure signal (zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure regulators); - pneumatic gas/air ratio pressure regulators, which change an air outlet pressure in response to a gas signal pressure or a gas signal differential pressure. This document is not applicable to: - pressure regulators connected directly to a gas distribution network or to a container that maintains a standard distribution pressure; - pressure regulators intended for gas appliances to be installed in the open air and exposed to the environment; - mechanically linked gas/air ratio controls; - electronic gas/air ratio controls (EN 12067 2:2022). The 4th paragraph of EN 13611:2019, Clause 1 is removed.

EN 88-1:2022相似标准


推荐

市场监管总局:对商用燃气燃烧器具等产品实施强制性产品认证管理

独立安装在防爆灯具之外LED模块用直流/交流电子控制装置2. 独立安装在防爆灯具之外气体放电灯用镇流器燃气燃烧器具商用燃气燃烧器具(2404)以城镇燃气为能源,燃烧用空气取自室内、燃烧产物直接或间接排向室外商用燃气燃烧器具及类似用途燃具。1. 额定热负荷不大于80kW、蒸汽压力不大于 80kPa,且设计正常水位水容积小于30L蒸汽发生器类燃具;2. ...

燃气用具中一氧化碳、二氧化碳以及氧气检测

燃烧器具尾气检测装置COPA-3000是为燃烧器具尾气专用而开发出来产品。它可以连续检测尾气中CO(一氧化碳)/CO2(二氧化碳)/O2(氧气)这3种成分浓度。COPA-3000系列分析仪可为燃气用具烟气提供更加稳定、精度更高检测,可在燃气用具研发检测领域发挥威力。...

水平垂直燃烧试验仪用途

16.产品全系标配燃气泄露报警装置安全可靠。试样制备试验说明请参照具体试验方法1,气体燃烧器一个改进本生灯提供了非睡衣测试包。燃烧器包括火焰高度计导光管。对于儿童睡衣测试包提供安装在测试室侧壁上倾斜侧燃烧器。2,气连接气体混合物应是甲烷,99%纯,或在适用测试方法。如果使用侧燃烧器,则通过客户提供压力调节器将气体供应线直接连接到燃烧器入口。...

水流型气体热量计SY-4高位热值、低位热值专用仪器

热量计本体应不漏水,各调节器能正常调节,各紧固件无松动。测试条件环境温度为(15~30)℃,比水温高(1.5~2.5)℃,水温波动小于0.1℃,检定过程中室温波动超过±1℃。热量计及检定设备应置于没有热辐射影响、没有强空气对流环境中。室内装有排风装置,以便排除烟气。检定开始前,燃气湿润器、湿式气体流量计、气体稳压器内水温应与室温达到平衡,其温差超过±0.5℃。...


谁引用了EN 88-1:2022 更多引用





Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号