ISO 10825-1:2022
齿轮.轮齿的磨损和损坏.第1部分:术语和特性

Gears — Wear and damage to gear teeth — Part 1: Nomenclature and characteristics


标准号
ISO 10825-1:2022
发布
2022年
发布单位
国际标准化组织
当前最新
ISO 10825-1:2022
 
 
引用标准
ISO 1122-1
适用范围
This document provides nomenclature for general modes of gear tooth wear and failure. It classifies, identifies, and describes the most common types of failure and provides information that, in many cases, enables the user to identify failure modes and evaluate the degree or change from original condition. This document is based on experience with steel gears; however, many of the failure modes discussed apply to gears made from other materials. Not all failure modes that can occur on other types of gears, such as plastic, bronze, or powder metal gears, are included. The solution to many gear problems requires detailed investigation and analysis by specialists and is beyond the scope of this document. This document specifies only the terminology intended to help with the identification and reporting of the appearance and conditions of gears after a period of operation. Neither causes nor preventive measures for any condition described are discussed. In this document, gear refers to both gear wheels and pinions, unless the gear is specifically identified. This document does not define “gear failure”.

ISO 10825-1:2022相似标准


推荐

齿轮修复方法

齿轮磨损失效是生产实际设备维护保养中经常遇到问题。对失效齿轮如何恢复其原有性能,延长其使用寿命并减少投入,节约成本一直是人们所关注问题。下面将目前常用齿轮磨损失效修复方法总结如下:1、调整换位法   调整换位法是将已磨损齿轮变换方位,利用齿轮磨损磨损较轻另一齿面继续工作方法。采用这种方法前提是齿轮单向受力运转或齿面单面磨损。由于这种方法能以zui经济方式实现齿轮180。...

球磨机安装注意事项及维护检修

11、磨机衬板被磨损70%或有 70mm长裂纹时应更换。  12、衬板螺栓有损坏造成衬板松动时应更换。  13、主轴承严重磨损时应更换。  14、格子式球磨机篦子板磨损到不能再焊补时应更换。  15、大齿轮齿轮磨损到一定程度后可翻面继续使用。  16、小齿轮严重磨损应更换。  17、进出料螺旋磨损时应及时焊补,磨损至无法焊补时应更换。  18、地脚螺栓松动或损坏应及时修复。  ...

齿轮基本概念及驱动装置

为便于安装,制造商设计了一个环形螺栓安装面,以使与其它设备法兰安装相配合,这使得筒形法兰制造更容易。  PEP-II齿轮泵带有与泵规格相匹配加热元件,可供用户选配,这可保证加温快速热量控制。与泵体内加热方式不同,这些元件损坏只限于一个板子上,与整个泵无关。  驱动装置  齿轮泵由一个独立电机驱动,可有效地阻断上游压力脉动及流量波动。在齿轮泵出口处压力脉动可以控制在1%以内。...

橡胶拉力机常见故障及解决方法分析

 橡胶拉力机在使用时要时常给机器各零件加润滑油,减少他们磨损。橡胶拉力机使用过程中若出现“喀喀”声或“嘎吱”声,则为轴承内滚珠不规则运动而产生声音,这是轴承内滚珠损坏或电动机长期不用,润滑脂干涸所致,下面我们就常见误差产生方式消除方法做一个简要说明。  1、橡胶拉力机安装不正确产生误差  橡胶拉力机安装不水平,会增加各活动部件之间摩擦力,影响垂直安装,从而给试验机带来误差。  ...





Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号