ASTM C29/C29M-23由美国材料与试验协会 US-ASTM 发布于 2023-10-01。
ASTM C29/C29M-23在国际标准分类中归属于: 19.060 机械试验。
ASTM C29/C29M-23 集料体积密度(“单位重量”)和空隙的标准试验方法的最新版本是哪一版?
最新版本是 ASTM C29/C29M-23 。
* 在 ASTM C29/C29M-23 发布之后有更新,请注意新发布标准的变化。
1.1 This test method covers the determination of bulk density (“unit weight”) of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to aggregates not exceeding 125 mm [5 in.] in nominal maximum size. NOTE 1—Unit weight is the traditional terminology used to describe the property determined by this test method, which is weight per unit volume (more correctly, mass per unit volume or density). 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard, as appropriate for a specification with which this test method is used. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E11. Within the text, inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
国内毛体积密度测试方法 《JTG E20-2011公路工程沥青及沥青混合料试验规程》规定的密度测试方法有以下四种:1水中重法(T0706-2011)水中重法用于測定几乎不吸水的密级配沥青混合料试件的表观相对密度或表现密度。其基本原理是一个物体的体积等于其在水中的缺失的重量。...
我国从事海外道路建设工程的单位已在当地按照国际标准广泛使用此试验方法。因此,新规范也收录了这种试验方法。这种试验设备通过对填料进行100次压实,记录试样的质量和压实后的高度来计算干压空隙率。操作方便,计算简单,便于推广应用。...
复现性试验从三种不同类型的沥青混合料试件中(密级配沥青混合料、SMA玛蹄脂碎石沥青混合料、开级配沥青混合料)分别取出三个试件,分别用三种试验方法对每一个试件进行毛体积密度测定,每个试件每种方法分别测定三次,并记录数据。对数据进行标准偏差和变异系数分析。分析结果如下表所示。...
Mist模拟仓内,盛满水● 仓盖关闭后,设置仓内温度、气压压力和气压循环次数,三个参数均可调节● 通过气压循环(有压、无压)来模拟试件内空隙水压,破坏试件内部粘附力(沥青和集料)和粘聚力(沥青与沥青)MIST水稳定性判断标准● 测试前后试件毛体积密度变化率<1.5%,认为水稳定性良好● 测试前后试件劈裂强度比,80%以上,认为水稳定性较好● 视觉评定欲了解MIST产品更多信息,欢迎联系INSTROTEK...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号