GSO ASTM D4014:2022
桥梁用滑动轴承和钢层弹性轴承的标准规范

Standard Specification for Plain and Steel-Laminated Elastomeric Bearings for Bridges


 

 

非常抱歉,我们暂时无法提供预览,您可以试试: 免费下载 GSO ASTM D4014:2022 前三页,或者稍后再访问。

您也可以尝试购买此标准,
点击右侧 “立即购买” 按钮开始采购(由第三方提供)。

 

标准号
GSO ASTM D4014:2022
发布
2022年
发布单位
GSO
当前最新
GSO ASTM D4014:2022
 
 
适用范围
This specification covers bearings, which consist of all elastomer or of alternate laminates of elastomer and steel, when the function of the bearings is to transfer loads or accommodate relative movement between a bridge superstructure and its supporting structure, or both. The bearings are furnished in four types as follows: plain elastomeric bearing pad; plain elastomeric sandwich bearing; steel-laminated elastomeric bearing; and steel-laminated elastomeric bearing with external load plate. The elastomer for the manufacture of the bearing is furnished in two types: Type CR and Type NR. The elastomer for the manufacture of the bearing is furnished in four grades of low-temperature properties: Grade 0; Grade 2; Grade 3; and Grade 5. The elastomeric compound used in the construction of a bearing shall contain only either natural rubber or chloroprene rubber as the raw polymer. Internal steel laminates shall be of rolled mild steel. Plain bearing pads shall be molded individually, or cut from previously molded strips or slabs, or extruded and cut to length. A steel-laminated bearing or a plain sandwich bearing shall be molded as a single unit under pressure and heat. All bonding of elastomer to steel laminates and to external load plates shall be carried out during molding. Bearing compression tests, compression stiffness, visual inspection, quality control properties, shear modulus, ozone resistance, and low-temperature grade tests shall be performed to conform to the specified requirements.

GSO ASTM D4014:2022相似标准


推荐

无密封离心泵选用时应注意问题

(3) 温度探头      温度探头(RTD)来监测隔离套温度,以反映泵在操作中状态变化。可防止泵干运转、内外轴承磨损、严重汽蚀、闷泵、泵卡住、以及系统过热等。(4) 差压开关     差压开关来监测泵出口压力变化,可防止泵干运转、严重汽蚀、闷泵、泵卡住等。尤其适用于容器卸空/槽车卸载等。(5) 第二保护a. 承压密闭磁耦合箱体     隔离套外为磁耦合箱体,如图1虚线部分。...

【显微分析】金属失效必备知识

比如,退火断口用于轴承工具,可以检查晶粒均匀细密程度,以显示碳析出、夹杂、缩孔等缺陷。调质断口只用于少数钢材,断口形貌能在一定程度上反映力学性能。2 高倍组织检验,即显微组织检验,是放大100 ~ 2000倍显微镜对金属材料内部进行观察分析检验方法。...

安全鞋冲击试验机/钢包头冲击试验机操作指南

安全鞋冲击试验机/钢包头冲击试验机操作方法之试样准备:1、从三个不同码数鞋子里各取一双未测试过鞋子来做试件。2、找出鞋子中心轴线(画法见标准资料)。3、用手压下鞋面,在中心轴线方向上找出头后沿向后20mm处取点,过此点沿中心轴线垂直方向画一条标记线。4、美工刀从标记线处割下(包括鞋底及鞋垫)鞋前头。5、钢尺在鞋垫上作出与中心轴线相对应直线,即为鞋头内部中轴线。...

MOUKEN纺织轴承产品分类及特性

轴承使用效果好坏与使用环境有关,并不是说碳钢轴承不好,这要看用到哪个机械上,因为有些并不需要碳钢周轴承就合适了。当然洛要好但造价就高多了,标准轴承是Gcr15。第四,在轴承材料与性能方面。例如轴承套圈滚动体一要反复承受高接触压力,另外进行伴随有滑动滚动接触,同时保持高精度旋转。...





Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号