ASTM D3917-23
热固性玻璃增强塑料拉挤型材的尺寸公差标准规范
Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes
ASTM D3917-23 发布历史
ASTM D3917-23由美国材料与试验协会 US-ASTM 发布于 2023-11-01。
ASTM D3917-23在国际标准分类中归属于: 83.140.20 层压薄板。
ASTM D3917-23 热固性玻璃增强塑料拉挤型材的尺寸公差标准规范的最新版本是哪一版？
最新版本是 ASTM D3917-23 。
ASTM D3917-23 发布之时，引用了标准
- ASTM D883 塑料相关标准术语*， 2024-02-01 更新
* 在 ASTM D3917-23 发布之后有更新，请注意新发布标准的变化。
ASTM D3917-23的历代版本如下：
- 2023年 ASTM D3917-23 热固性玻璃增强塑料拉挤型材的尺寸公差标准规范
- 2015年 ASTM D3917-15a 热固性玻璃钢拉挤型材尺寸公差的标准规格
- 2015年 ASTM D3917-15e1 热固性玻璃增强塑料挤拉制型材尺寸公差的标准规范
- 2015年 ASTM D3917-15 热固性玻璃增强塑料挤拉制型材尺寸公差的标准规范
- 2012年 ASTM D3917-12 热固性玻璃增强塑料拉挤形状尺寸公差的标准规格
- 2011年 ASTM D3917-11 热固性玻璃增强塑料拉挤形状尺寸公差的标准规范
- 2008年 ASTM D3917-08 热固性玻璃纤维增强塑料挤拉制型材尺寸公差的标准规范
- 1996年 ASTM D3917-96(2002)e1 热固性玻璃纤维增强塑料挤拉制型材尺寸公差的标准规范
- 1996年 ASTM D3917-96 热固性玻璃纤维增强塑料挤拉制型材尺寸公差的标准规范
1.1 This specification defines production tolerances applicable to standard rods, bars, shapes, and flat sheet pultruded from thermosetting glass-reinforced plastics. 1.2 These dimensional tolerances apply to all shapes specified as “standard” by the pultrusion industry. 1.3 Custom shapes and products designed for special applications may carry specific tolerances that vary from the standard. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
