ISO 9120:1997/Amd 1:1998
石油及相关产品 汽轮机及其他油品脱气性能的测定 冲击器法

Petroleum and related products — Determination of air-release properties of steam turbine and other oils — Impinger method


标准号
ISO 9120:1997/Amd 1:1998
发布
1997年
发布单位
/
替代标准
ISO 9120:1997/Amd 1:2019
当前最新
ISO 9120:1997/Amd 1:2019
 
 
适用范围
This International Standard specifies a method for the estimation of the ability of a petroleum-type steam turbine oil to be separated from entrained air. NOTES 1 The impinger method described in this International Standard is used for determining the air-release ability of the oils tested. Air bubbles dispersed in the oil influence the compressibility and can cause malfunctions. This method may not be suitable for ranking oils in applications where residence times are short and gas contents high. 2 Agitation of lubricating oil with air in equipment such as bearings, couplings, gears, pumps and oil return lines, may produce a dispersion of finely divided air bubbles in the oil. If the residence time in the reservoir is too short to allow the air bubbles to rise to the oil surface, a mixture of air and oil will circulate through the lubricating oil system. This may result in an inability to maintain oil pressure (particularly with centrifugal pumps), incomplete oil films in bearings and gears, and poor hydraulic system performance or failure. 3 This test measures the time for the entrained air content to fall to the relatively low value of 0,2 % (V/V) under a standardized set of test conditions, and hence permits the comparison of the ability of oils to separate entrained air under conditions where a separation time is available. Although the significance of the test results is not fully established, sponginess and lack of sensitivity of the control systems of some turbines may be related to the air release properties of the oil. System design and system pressure are other variables. 4 For the purposes of this International Standard, the expression “%(V/V)” is used to represent the volume fraction of a material.

ISO 9120:1997/Amd 1:1998相似标准


推荐

为什么要进行润滑油黏度、酸值测定

3、运动黏度主要测试方法GB/T265-1988(2004)石油产品运动黏度和动力黏度计算法GB/T11137-1989(2004)深色石油产品运动黏度测定法(逆流)和动力黏度计算法ASTMD445-2019a透明和不透明液体运动黏度测定动力黏度计算法ASTMD7279-2018e1透明和不透明液体运动黏度测定自动折管式黏度计4、运动黏度意义运动黏度是工业润滑油牌号划分依据;运动黏度是设备选用润滑油主要依据之一...

想知道液压油污染度检测仪功能特点不妨看看这些

测定方法是将油样经真空过滤,使油样中颗粒平均分布于微孔滤膜上,在油污染度比较显微镜透射光下,与油污染度分级标准模板进行比较,确定油样颗粒污染度等级。可广泛应用于电力、石油、化工、商检、高校科研等部门。   液压油污染度检测仪功能特点:   1、采用光阻(遮光)计数原理,检测速度快,精度高。   2、高精度激光传感,测试范围宽,性能稳定,噪声低,分辨率高。   ...

液压油污染度检测仪用于测量油品颗粒污染度

  液压油污染度检测仪用于测量磷酸酯抗燃油、汽轮机油、变压油及其他各种辅机用油等油品颗粒污染度。   尤其适用油样乳化现象严重或黏度过大油品测定方法是将油样经真空过滤,使油样中颗粒平均分布于微孔滤膜上,在油污染度比较显微镜透射光下,与油污染度分级标准模板进行比较,确定油样颗粒污染度等级。可广泛应用于电力、石油、化工、商检、高校科研等部门。   ...

【质量控制】石化油品质量常见检测项目与检测方法

5、残炭测定油品残炭是指将油品放入残炭测定中,在不通入空气试验条件下,加热使其蒸发和分解,排出气体燃烧后所剩余焦黑色残留物。它是衡量油品中胶状物质和不稳定化合物间接指标,其值越大,表明油品中不稳定烃类和胶状物质就越多。石油产品残炭测定法有GB/T 268《石油产品残炭测定法》、SH/T 0170《电炉残炭》和GB/T 17144《微量残炭》,测定结果用质量分数表示。 ...





Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号