GSO ISO 4407:2015由GSO 发布于 2015-09-03。
GSO ISO 4407:2015在国际标准分类中归属于: 23.100.60 过滤器、密封垫和流体杂质。
GSO ISO 4407:2015 流体的液压能力 流体污染 使用光学显微镜通过统计测定分子污染的最新版本是哪一版?
最新版本是 GSO ISO 4407:2015 。
This International Standard specifies methods for determining the level of particulate contamination in liquids used in hydraulic systems by counting the number of particles deposited on the surface of a membrane filter using an optical microscope. It includes particle counting by two manual methods and image analysis, using either transmitted or incident lighting systems. Particle sizes ≥ 2 µm can be sized and counted by this method, but the resolution and accuracy of the results will depend upon the optical system used and the capabilities of the operator. All hydraulic fluids with a wide range of contamination levels can be analysed according to this International Standard. However, the counting uncertainty at the larger particle sizes increases if the volume filtered is reduced to allow smaller sized particles to be counted, where a fine precipitate or a high particle concentration is present.
测定方法是将油样经真空过滤,使油样中的颗粒平均分布于微孔滤膜上,在油污染度比较显微镜的透射光下,与油污染度分级标准模板进行比较,确定油样的颗粒污染度等级。 液压油污染度检测仪主要能够检测油液中颗粒污染度和油液中的水分。检测油液中颗粒污染度是使用半导体激光器搭建,光阻法原理在线测量油液中累计颗粒数,能方便的探知油液中的金属颗粒大小以及油液流速。 ...
如果清洁度分析的最终目标是找到并清除污染物来源,则了解颗粒物的成分便十分有用。在这种情况下,理想的解决方案应能够帮助用户高效可靠地识别颗粒物材料。图3:使用光学显微镜和激光光谱确定的铝合金颗粒物的成分。★“清洁度分析解决方案徕卡清洁度分析解决方案基于光学显微镜和激光诱导击穿光谱(LIBS),可帮助用户在滤膜上开展高效和准确的颗粒物污染分析。...
锂电池负极集流体的铜箔粗糙度测定 使用奥林巴斯 OLS5000 显微镜测量粗糙度时,用户会得到以下三种类型的信息:粗糙度数据,激光显微镜3D彩色图像和高度信息以及光学显微镜真实彩色图像。 这让使用人直观的看到粗糙度数据。同时,使用人可以从数据中了解集流体表面的状态。通过观察这些图像,也可以观察到实际的表面形貌。 ...
7:– 过滤器使用寿命是指在实际操作中,直到过滤器的污染水平高到超过允许的流动阻力为止的运行时间。– 污染等级动力液压和润滑系统的传输是通过压力流体实现的。这些流体具有自然污染(初级和次级污染)。这种污染的水平(定义流体体积中的颗粒数量)在 ISO 4406 和 NAS 1638 标准中定义。它们分为污染等级。...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号