BS 7158-2001
排放物和污物用的塑料制检查容器已作废

Plastics inspection chambers for drains and sewers - Specification

BS 7158-2001 发布历史

This British Standard specifies requirements for plastics inspection chambers for use at depths to invert not exceeding 6 m in the construction of drainage and sewerage systems. It is applicable to non-man-entry chambers with or without raising pieces and having a nominal cross-section as recommended in Table NB.2 of BS EN 752-3:1997, as amended in 2000. The chambers are classified into four grades as a function of stiffness (see 7.6) and strength (see 7.7), to suit different depths of installation and location for exposure to surface loading (see Annex H). Attention is drawn to BS EN 124:1994 and BS 4660 which specify requirements for covers and frames for drainage purposes that are applicable to inspection chambers. This standard specifies materials, dimensions and tolerances, physical and performance characteristics and marking for plastics inspection chambers for drains and sewers.

BS 7158-2001由英国标准学会 GB-BSI 发布于 2001-08-15，并于 2001-08-15 实施，于 2013-01-01 废止。

BS 7158-2001 在中国标准分类中归属于: G94 非金属化工机械设备，在国际标准分类中归属于: 91.140.80 排水系统。

BS 7158-2001的历代版本如下：

• 2001年08月15日 BS 7158-2001 排放物和污物用的塑料制检查容器

BS 7158-2001 排放物和污物用的塑料制检查容器 于 2003-12-18 变更为 BS EN 13598-1-2003 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).第1部分:包括浅层检验室在内的辅助配件规范。

BS 7158-2001 排放物和污物用的塑料制检查容器 于 2011-03-31 变更为 BS EN 13598-1-2010 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U),聚丙烯(PP)和聚乙烯(PE).包括浅层检验室在内的辅助配件规范。

BS 7158-2001 排放物和污物用的塑料制检查容器 于 2009-02-28 变更为 BS EN 13598-2-2009 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U),聚丙烯(PP)和聚乙烯(PE).第2部分:交通范围和地下设施中检修孔和检查室用规范。

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 BS 7158-2001 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

BS 7158-2001

发布日期

2001年08月15日

实施日期

2001年08月15日

废止日期

2013-01-01

中国标准分类号

G94

国际标准分类号

91.140.80

发布单位

GB-BSI

代替标准

BS EN 13598-1-2003 BS EN 13598-1-2010 BS EN 13598-2-2009

适用范围

This British Standard specifies requirements for plastics inspection chambers for use at depths to invert not exceeding 6 m in the construction of drainage and sewerage systems. It is applicable to non-man-entry chambers with or without raising pieces and having a nominal cross-section as recommended in Table NB.2 of BS EN 752-3:1997, as amended in 2000. The chambers are classified into four grades as a function of stiffness (see 7.6) and strength (see 7.7), to suit different depths of installation and location for exposure to surface loading (see Annex H). Attention is drawn to BS EN 124:1994 and BS 4660 which specify requirements for covers and frames for drainage purposes that are applicable to inspection chambers. This standard specifies materials, dimensions and tolerances, physical and performance characteristics and marking for plastics inspection chambers for drains and sewers.