IEC 62394-2006
消费者电子产品和网络用服务诊断接口.ECHONET的实施

Service diagnostic interface for consumer electronics products and networks – Implementation for ECHONET (Edition 2.0)

IEC 62394-2006 发布历史

This International Standard specifies requirements for service diagnostic software to be implemented in products that incorporate a digital interface. It does not specify requirements for carrying out remote diagnosis or for manufacturer-dependent software. The SDI requires the use of a controller (exclusive controller or general-purpose controller/PC) into which service diagnostic software can be loaded. Part of this controller software should be standardized while another part of this controller software is manufacturer-/product-related. To reach a common approach in servicing all products from all manufacturers it is necessary to standardize specific items in the products (device under test (DUT)) as well as in the diagnostic software on the controller. The SDI is based upon the ECHONET specification because this interface will be used in most future products. The use of this connection and existing communication protocols enable implementation in products at low cost and gives maximum flexibility and efficiency. The SDI consists of ? the specific hardware and software requirements of the DUT; ? the specific requirements of the controller: – the service software; – an ECHONET interface (to be built in if not already present); ? the connection between the controller and the DUT. This specification is the minimal specification necessary to be able to carry out computerized diagnosis and covers the standardized software of the controller as well as the standardized software and provisions in the DUT.

IEC 62394-2006由国际电工委员会 IX-IEC 发布于 2006-06。

IEC 62394-2006 在中国标准分类中归属于: M11 通信网技术体制，在国际标准分类中归属于: 33.160.99 其他音频、视频和视听设备,35.100 开放系统互连(OSI),35.110 网络。

IEC 62394-2006的历代版本如下：

• 2006年06月 IEC 62394-2006 消费者电子产品和网络用服务诊断接口.ECHONET的实施
• 2013年09月 IEC 62394-2013 消费类电子产品和网络用服务诊断接口. ECHONET的实施
• 2017年04月11日 IEC 62394-2017 用于消费电子产品和网络的服务诊断接口 - Echonet的实施

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 IEC 62394-2006 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

IEC 62394-2006

发布日期

2006年06月

实施日期

废止日期

无

中国标准分类号

M11

国际标准分类号

33.160.99;35.100;35.110

发布单位

IX-IEC

代替标准

IEC 62394-2013

适用范围

This International Standard specifies requirements for service diagnostic software to be implemented in products that incorporate a digital interface. It does not specify requirements for carrying out remote diagnosis or for manufacturer-dependent software. The SDI requires the use of a controller (exclusive controller or general-purpose controller/PC) into which service diagnostic software can be loaded. Part of this controller software should be standardized while another part of this controller software is manufacturer-/product-related. To reach a common approach in servicing all products from all manufacturers it is necessary to standardize specific items in the products (device under test (DUT)) as well as in the diagnostic software on the controller. The SDI is based upon the ECHONET specification because this interface will be used in most future products. The use of this connection and existing communication protocols enable implementation in products at low cost and gives maximum flexibility and efficiency. The SDI consists of ? the specific hardware and software requirements of the DUT; ? the specific requirements of the controller: – the service software; – an ECHONET interface (to be built in if not already present); ? the connection between the controller and the DUT. This specification is the minimal specification necessary to be able to carry out computerized diagnosis and covers the standardized software of the controller as well as the standardized software and provisions in the DUT.

谁引用了IEC 62394-2006 更多引用