DIN EN 14620-1-2006
工作温度为0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制作的设计和生产.第1部分:总则.英文版本DIN EN 14620-1-2006-12
Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 1: General; English version of DIN EN 14620-1:2006-12
DIN EN 14620-1-2006 发布历史
This European Standard is a specification for vertical, cylindrical tanks, built on site, above ground and of which the primary liquid container is made of steel. The secondary container, if applicable, may be of steel or of concrete or a combination of both. An inner tank made only of pre-stressed concrete is excluded from the scope of this European Standard. This European Standard specifies principles and application rules for the structural design of the "containment" during construction, testing, commissioning, operation (accidental included), and decommissioning. It does not address the requirements for ancillary equipment such as pumps, pumpwells, valves, piping, instrumentation, staircases etc. unless they can affect the structural design of the tank. This European Standard applies to storage tanks designed to store products, having an atmospheric boiling point below ambient temperature, in a dual phase, i.e. liquid and vapour. The equilibrium between liquid and vapour phases being maintained by cooling down the product to a temperature equal to, or just below, its atmospheric boiling point in combination with a slight overpressure in the storage tank. The maximum design pressure of the tanks covered by this European Standard is limited to 500 mbar. For higher pressures, reference can be made to EN 13445, Parts 1 to 5. The operating range of the gasses to be stored is between 0 °C and -165 °C. The tanks for the storage of liquefied oxygen, nitrogen and argon are excluded. The tanks are used to store large volumes of hydrocarbon products and ammonia with low temperature boiling points, generally called "Refrigerated Liquefied Gases" (RLG's). Typical products stored in the tanks are: methane, ethane, propane, butane, ethylene, propylene, butadiene (this range includes the LNG's and LPG's). NOTE Properties of the gases are given in Annex A. The requirements of this European Standard cannot cover all details of design and construction because of the variety of sizes and configurations that may be employed. Where complete requirements for a specific design are not provided, the intention is for the designer, subject to approval of the purchaser's authorized representative, to provide design and details that are as safe as those laid out in this European Standard. This European Standard specifies general requirements for the tank concept, selection and general design considerations.
DIN EN 14620-1-2006由德国标准化学会 DE-DIN 发布于 2006-12。
DIN EN 14620-1-2006 在中国标准分类中归属于: A82 包装材料与容器，在国际标准分类中归属于: 23.020.10 固定容器和罐。
DIN EN 14620-1-2006 发布之时，引用了标准
- EN 1991-1-4 欧洲法规1:对结构物的作用.第1-4部分:一般作用.风作用［代替:CEN ENV 1991-2-4］
- EN 1991-1-6 欧洲法规1:对建筑物的作用.一般作用.实行中的作用.合并勘误表2008年7月［代替:CEN ENV 1991-2-6］
- EN 1997-1-2004 欧洲法规7:土木技术设计.第1部分:总则*， 2022-07-18 更新
- EN 1998-1-2004 欧洲法规8:抗震结构设计规定.第1部分:一般规则,地震作用和结构一般要求.合并勘误表-2009年7月［代替:CEN ENV 1998-1-1,CEN ENV 1998-1-2,CEN ENV 1998-1-3］*， 2022-07-18 更新
* 在 DIN EN 14620-1-2006 发布之后有更新，请注意新发布标准的变化。
DIN EN 14620-1-2006的历代版本如下：
- 2006年12月 DIN EN 14620-1-2006 工作温度为0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制作的设计和生产.第1部分:总则.英文版本DIN EN 14620-1-2006-12
DIN EN 14620-1-2006 工作温度为0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制作的设计和生产.第1部分:总则.英文版本DIN EN 14620-1-2006-12 由 DIN 4119-1-1979 变更而来。
DIN EN 14620-1-2006 工作温度为0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制作的设计和生产.第1部分:总则.英文版本DIN EN 14620-1-2006-12 由 DIN 4119-2-1980 变更而来。
- 标准号
- DIN EN 14620-1-2006
- 发布日期
- 2006年12月
- 实施日期
- 废止日期
- 无
- 中国标准分类号
- A82
- 国际标准分类号
- 23.020.10
- 发布单位
- DE-DIN
- 引用标准
- EN 1991-1-4 EN 1991-1-6 EN 1992-1-2004 EN 1997-1-2004 EN 1998-1-2004
- 被代替标准
- DIN 4119-1-1979 DIN 4119-2-1980
- 适用范围
- This European Standard is a specification for vertical, cylindrical tanks, built on site, above ground and of which the primary liquid container is made of steel. The secondary container, if applicable, may be of steel or of concrete or a combination of both. An inner tank made only of pre-stressed concrete is excluded from the scope of this European Standard. This European Standard specifies principles and application rules for the structural design of the "containment" during construction, testing, commissioning, operation (accidental included), and decommissioning. It does not address the requirements for ancillary equipment such as pumps, pumpwells, valves, piping, instrumentation, staircases etc. unless they can affect the structural design of the tank. This European Standard applies to storage tanks designed to store products, having an atmospheric boiling point below ambient temperature, in a dual phase, i.e. liquid and vapour. The equilibrium between liquid and vapour phases being maintained by cooling down the product to a temperature equal to, or just below, its atmospheric boiling point in combination with a slight overpressure in the storage tank. The maximum design pressure of the tanks covered by this European Standard is limited to 500 mbar. For higher pressures, reference can be made to EN 13445, Parts 1 to 5. The operating range of the gasses to be stored is between 0 °C and -165 °C. The tanks for the storage of liquefied oxygen, nitrogen and argon are excluded. The tanks are used to store large volumes of hydrocarbon products and ammonia with low temperature boiling points, generally called "Refrigerated Liquefied Gases" (RLG's). Typical products stored in the tanks are: methane, ethane, propane, butane, ethylene, propylene, butadiene (this range includes the LNG's and LPG's). NOTE Properties of the gases are given in Annex A. The requirements of this European Standard cannot cover all details of design and construction because of the variety of sizes and configurations that may be employed. Where complete requirements for a specific design are not provided, the intention is for the designer, subject to approval of the purchaser's authorized representative, to provide design and details that are as safe as those laid out in this European Standard. This European Standard specifies general requirements for the tank concept, selection and general design considerations.