AS 1646.3-2000
供水系统用橡胶密封件.第3部分:水和废水用管接头密封件(除天然橡胶和聚异戊二烯合成橡胶外)的材料要求

Elastomeric seals for waterworks purposes Part 3: Material requirements for pipe joint seals used in water and wastewater applications with the exception of natural rubber and polyisoprene compounds

AS 1646.3-2000 发布历史

This Standard specifies requirements for synthetic elastomeric materials used in vulcanized seals with the exception of natural rubber and polyisoprene compounds for— (a) cold potable water supply (up to 50°C); (b) hot potable and non-potable water supply (up to 110°C); (c) drainage, sewerage and rainwater systems (continuous flow up to 45°C and intermittent flow up to 95°C); The different designations of seals specified are defined according to their type, application and requirements (see Table 4.1). General requirements for finished joint seals are also given. Any additional requirements called for by the particular application are specified in the relevant product Standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This Standard should be used, where appropriate, with product Standards that specify performance requirements for joints. This Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics; and elastomeric components of composite or non-composite seals. In the case of composite seals for materials of hardness ranges from 76 IRHD to 96 IRHD, the requirements for elongation at break, compression set and stress relaxation apply only when the material is participating in the sealing function, or the long-term stability of the seal. Joint seals made with an enclosed void as part of their design are included in the scope of this Standard. Means for demonstrating compliance with this Standard are given in Appendix A.

AS 1646.3-2000由澳大利亚标准协会 AU-SA 发布于 2000-04-28。

AS 1646.3-2000 在中国标准分类中归属于: G43 橡胶密封件。

AS 1646.3-2000 发布之时，引用了标准

• AS 1646 自来水工程用弹性密封圈
• AS 1646.1 供水系统用合成橡胶密封件.第1部分:一般要求
• AS 1646.2 供水系统用合成橡胶密封件.第2部分:水和废水用管接头密封件的材料要求.说明性的简洁表达

AS 1646.3-2000的历代版本如下：

• 2000年04月28日 AS 1646.3-2000 供水系统用橡胶密封件.第3部分:水和废水用管接头密封件(除天然橡胶和聚异戊二烯合成橡胶外)的材料要求

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 AS 1646.3-2000 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

AS 1646.3-2000

发布日期

2000年04月28日

实施日期

废止日期

无

中国标准分类号

G43

发布单位

AU-SA

引用标准

AS 1199 AS 1646 AS 1646.1 AS 1646.2 AS 1683

适用范围

This Standard specifies requirements for synthetic elastomeric materials used in vulcanized seals with the exception of natural rubber and polyisoprene compounds for— (a) cold potable water supply (up to 50°C); (b) hot potable and non-potable water supply (up to 110°C); (c) drainage, sewerage and rainwater systems (continuous flow up to 45°C and intermittent flow up to 95°C); The different designations of seals specified are defined according to their type, application and requirements (see Table 4.1). General requirements for finished joint seals are also given. Any additional requirements called for by the particular application are specified in the relevant product Standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This Standard should be used, where appropriate, with product Standards that specify performance requirements for joints. This Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics; and elastomeric components of composite or non-composite seals. In the case of composite seals for materials of hardness ranges from 76 IRHD to 96 IRHD, the requirements for elongation at break, compression set and stress relaxation apply only when the material is participating in the sealing function, or the long-term stability of the seal. Joint seals made with an enclosed void as part of their design are included in the scope of this Standard. Means for demonstrating compliance with this Standard are given in Appendix A.

AS 1646.3-2000系列标准

谁引用了AS 1646.3-2000 更多引用