DIN EN 15035-2007
加热锅炉.额定输入功率≤70kW的燃油室封闭容器的特殊要求

Heating boilers - Special requirements for oil fired room sealed units up to 70 kW; English version of DIN EN 15035:2007-05

DIN EN 15035-2007 发布历史

This European Standard applies to type Cxs central heating boilers as specified in 4.1, equipped with atomizing oil burners: — type C_13, type C_33 and type C_53 boilers, including their combustion air supply and combustion products evacuation ducts and their terminals; — type C_43 boilers including their connection ducts but without the chimney which is erected as a shared duct system and which is part of the building; — type Ce3 boilers, including the connecting piece as specified in 3.7, if not integrated into the boiler; — type Cg3 boilers, including their connection ducts but without the chimney which is part of the building; — that have a nominal useful heat output below or equal to 70 kW; — where the temperature of the water does not exceed 100 °C during normal operation; — where the maximum water-side operating pressure does not exceed 8 bar. This European Standard is intended to establish specific requirements and test methods for type C atomizing oil burning central heating boilers with respect to construction, safety, fitness for purpose, rational use of energy, classification and marking. This European Standard covers only standard tests. For boilers that produce domestic hot water by a drum or a heat exchanger, integrated or juxtaposed, (by accumulation of instant production), this standard only applies to hot water reheating system components that are not subject to operating conditions applicable to the boiler heating system. This European Standard covers units consisting of boilers equipped with burners that meet the requirements of EN 267, with the following exceptions: — maximum NO and CO emission values, estimated for boilers according to the classes defined in EN 303-2; — air factor value, defined by the manufacturer and stated in the boiler's technical specifications; — marking and/or burner data plate which may provide information for the boiler data plate; — installation recommendations for installing the burner on the boiler included in the boiler operating instructions. This European Standard modifies EN 303-1, EN 303-2, EN 304 and specifies supplementary requirements only for room sealed operations.

DIN EN 15035-2007由德国标准化学会 DE-DIN 发布于 2007-05。

DIN EN 15035-2007 在中国标准分类中归属于: J98 锅炉及其辅助设备，在国际标准分类中归属于: 97.100.40 液体燃料加热器。

DIN EN 15035-2007 发布之时，引用了标准

• EN 1443 
• EN 1457 烟囱.粘土/陶瓷烟道内衬.第2部分:烟道内衬在湿润条件下操作.要求和试验方法*， 2012-01-01 更新
• EN 1856-1 烟囱.金属制烟囱要求.第1部分:系统烟囱制品*， 2009-06-01 更新
• EN 1856-2 
• EN 13063-1 烟囱.带粘土和陶瓷烟道衬的系统烟筒.第1部分:防烟火的要求和试验方法.包含修改件A1-7/2007*， 2022-07-18 更新
• EN 13063-2 烟囱.带粘土和陶瓷烟道衬的系统烟筒.第2部分:潮湿条件下的要求和试验方法.包含修改件A1-7/2007
• EN 13216-1 烟囱.系统烟囱的试验方法.第1部分:一般试验方法
• EN 14471 烟囱.带塑料烟道衬的系统烟囱.要求和试验方法*， 2014-02-08 更新
• EN 15034 供热锅炉.燃油用冷凝式供热锅炉.合并勘误表2008年9月*， 2022-07-18 更新
• EN 267 液体燃料用自动强制通风燃烧器*， 2022-07-18 更新
• EN 303-1 *， 2017-09-01 更新
• EN 303-4 供暖锅炉.第4部分:强制通风式燃烧器的供暖锅炉.带输出功率最高为70KW和最大工作压力为3bar的强制通风式.术语,特殊要求,检验和标识
• EN 304-1992 供暖锅炉.雾化喷油嘴用供暖锅炉的试验规程
• EN 303-2-1998 供暖锅炉.第2部分:带鼓风机喷嘴的采暖锅炉.对带油雾化喷嘴的采暖锅炉的特殊要求

* 在 DIN EN 15035-2007 发布之后有更新，请注意新发布标准的变化。

DIN EN 15035-2007的历代版本如下：

• 2007年05月 DIN EN 15035-2007 加热锅炉.额定输入功率≤70kW的燃油室封闭容器的特殊要求

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 DIN EN 15035-2007 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

DIN EN 15035-2007

发布日期

2007年05月

实施日期

废止日期

无

中国标准分类号

J98

国际标准分类号

97.100.40

发布单位

DE-DIN

引用标准

EN 1443 EN 1457 EN 1856-1 EN 1856-2 EN 13063-1 EN 13063-2 EN 13216-1 EN 14471 EN 15034 EN 267 EN 303-1 EN 303-4 EN 304-1992 EN 303-2-1998

适用范围

This European Standard applies to type Cxs central heating boilers as specified in 4.1, equipped with atomizing oil burners: — type C_13, type C_33 and type C_53 boilers, including their combustion air supply and combustion products evacuation ducts and their terminals; — type C_43 boilers including their connection ducts but without the chimney which is erected as a shared duct system and which is part of the building; — type Ce3 boilers, including the connecting piece as specified in 3.7, if not integrated into the boiler; — type Cg3 boilers, including their connection ducts but without the chimney which is part of the building; — that have a nominal useful heat output below or equal to 70 kW; — where the temperature of the water does not exceed 100 °C during normal operation; — where the maximum water-side operating pressure does not exceed 8 bar. This European Standard is intended to establish specific requirements and test methods for type C atomizing oil burning central heating boilers with respect to construction, safety, fitness for purpose, rational use of energy, classification and marking. This European Standard covers only standard tests. For boilers that produce domestic hot water by a drum or a heat exchanger, integrated or juxtaposed, (by accumulation of instant production), this standard only applies to hot water reheating system components that are not subject to operating conditions applicable to the boiler heating system. This European Standard covers units consisting of boilers equipped with burners that meet the requirements of EN 267, with the following exceptions: — maximum NO and CO emission values, estimated for boilers according to the classes defined in EN 303-2; — air factor value, defined by the manufacturer and stated in the boiler's technical specifications; — marking and/or burner data plate which may provide information for the boiler data plate; — installation recommendations for installing the burner on the boiler included in the boiler operating instructions. This European Standard modifies EN 303-1, EN 303-2, EN 304 and specifies supplementary requirements only for room sealed operations.