SAE AIR 5797-2008
航空器轮胎轮廓开发和实验室测试的实施

Aircraft Tire Wear Profile Development and Execution for Laboratory Testing

SAE AIR 5797-2008 发布历史

This SAE Aerospace Information Report (AIR) describes the current process for performing comparative wear testing on aircraft tires in a laboratory environment. This technique is applicable to both radial and bias tires, and is pertinent for all aircraft tire sizes.This AIR describes a technique based upon “wear” energy. In this technique, side wear energy and drag wear energy are computed as the tire is run through a prescribed test program. The specifics that drive the test setup conditions are discussed in Sections 4 through 7. In general, the technique follows this process:• A test profile is developed from measured mechanical property data of the tires under study.• Each tire is repeatedly run to the test profile until it is worn to the maximum wear limit (MWL). Several tires, typically 5 to 10, of each tire design are tested.• Wear energy is computed for each test cycle and then summed to determine total absorbed wear energy.• An index is calculated for each tire design. This is accomplished by dividing the total linear inches of wear at the most worn point into the total wear energy.• The indexes are then normalized to provide a comparative wear rate. The described technique is not meant to provide an absolute wear rate or wear index because the technique does notproduce results that allow the user to say a tire will last for a specific number of landings. However, it does provide a comparative index. It will make a distinction from one tire design to another by indicating a percentage difference inabrasive wear rate under representative operational conditions. The technique has been demonstrated in a number of test programs and is shown to have an extremely high correlation to field data. Supporting data is included in Section 9.

SAE AIR 5797-2008由美国机动车工程师协会 US-SAE 发布于 2008-08-20。

SAE AIR 5797-2008 在中国标准分类中归属于: G41 轮胎。

SAE AIR 5797-2008的历代版本如下：

• 2008年08月20日 SAE AIR 5797-2008 航空器轮胎轮廓开发和实验室测试的实施

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 SAE AIR 5797-2008 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

SAE AIR 5797-2008

发布日期

2008年08月20日

实施日期

废止日期

无

中国标准分类号

G41

国际标准分类号

83.160.20

发布单位

US-SAE

引用标准

Cornering and Wear Behavior of the Space Shuttle Orbiter Main Gear Tire

适用范围

This SAE Aerospace Information Report (AIR) describes the current process for performing comparative wear testing on aircraft tires in a laboratory environment. This technique is applicable to both radial and bias tires, and is pertinent for all aircraft tire sizes.This AIR describes a technique based upon “wear” energy. In this technique, side wear energy and drag wear energy are computed as the tire is run through a prescribed test program. The specifics that drive the test setup conditions are discussed in Sections 4 through 7. In general, the technique follows this process:• A test profile is developed from measured mechanical property data of the tires under study.• Each tire is repeatedly run to the test profile until it is worn to the maximum wear limit (MWL). Several tires, typically 5 to 10, of each tire design are tested.• Wear energy is computed for each test cycle and then summed to determine total absorbed wear energy.• An index is calculated for each tire design. This is accomplished by dividing the total linear inches of wear at the most worn point into the total wear energy.• The indexes are then normalized to provide a comparative wear rate. The described technique is not meant to provide an absolute wear rate or wear index because the technique does notproduce results that allow the user to say a tire will last for a specific number of landings. However, it does provide a comparative index. It will make a distinction from one tire design to another by indicating a percentage difference inabrasive wear rate under representative operational conditions. The technique has been demonstrated in a number of test programs and is shown to have an extremely high correlation to field data. Supporting data is included in Section 9.