SAE J2271-2009
船舶系统和设备.柱头螺栓用部分标准.连续作用和双端引线(米制系列)
Ship Systems and Equipment Part Standard for Studs Continuous and Double End (Inch Series)
SAE J2271-2009 发布历史
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a. Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (0.190 through 4 inches); UNRF threads (0.190 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches) b. Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches); UNRF threads (1/4 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches); Different thread forms on each end are permissible. c. Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters; NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches); UNRC threads (1/4 through 4 inches) - UNRC threads (1/4 through 4 inches); UNRF threads (1/4 through 1-1/2 inches); UNRF threads (1/4 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches); 8UNR threads (1-1/8 through 4 Inches) These studs are primarily for use in ship systems and equipment. The continuous thread studs and the reduced body diameter double end studs are configurations particularly suited to applications that are subject to high impact (H.I.) shock requirements.
SAE J2271-2009由美国机动车工程师协会 US-SAE 发布于 2009-05-05。
SAE J2271-2009 在中国标准分类中归属于: J13 紧固件，在国际标准分类中归属于: 21.060.01 紧固件综合。
SAE J2271-2009 发布之时，引用了标准
- ASME B1.1-2003 统一标准英制螺纹(UN和UNR螺纹牙型)
- ASME B1.3M-1992 螺纹测量体系的可接受尺寸.英制和米制螺纹(UN,UNR,UNJ,M和MJ)
- ASME B1.12-1987 5级压配合螺纹
- ASME B18.18.1-2007 通用紧固件检验和质量保证
- ASTM A307-2007 抗拉强度为60000PSI的碳素钢螺栓和螺柱的标准规范*， 2022-12-17 更新
- ASTM A354-2007 淬火和回火合金钢螺栓、螺柱和其它外螺纹紧固件的标准规范*， 2022-12-17 更新
- ASTM A380-2006 不锈钢零件、设备及系统的清洗和除垢的标准操作规程*， 2022-12-17 更新
- ASTM A449-2007 通用最低拉伸强度为120/105/90ksi的热处理钢制六角头螺钉、螺栓和螺柱用标准规范*， 2022-12-17 更新
- ASTM A967-2005 不锈钢零件化学钝化处理的标准规范*， 2022-12-17 更新
- ASTM F468-2006 一般用途有色金属螺栓、六角头螺钉及螺柱标准规范*， 2022-12-17 更新
- ASTM F593-2002 不锈钢螺栓,六角头螺钉及螺柱标准规范*， 2022-12-17 更新
- ASTM F1 电子管用镀镍和镀镍钢带的标准规范
* 在 SAE J2271-2009 发布之后有更新，请注意新发布标准的变化。
SAE J2271-2009的历代版本如下：
- 1996年06月01日 SAE J2271-1996 针对双头螺栓的船舶系统和设备部分标准,连续和双端(英制系列)
- 2009年05月05日 SAE J2271-2009 船舶系统和设备.柱头螺栓用部分标准.连续作用和双端引线(米制系列)
- 标准号
- SAE J2271-2009
- 发布日期
- 2009年05月05日
- 实施日期
- 废止日期
- 无
- 中国标准分类号
- J13
- 国际标准分类号
- 21.060.01
- 发布单位
- 美国机动车工程师协会
- 引用标准
- ASME B1.1-2003 ASME B1.3M-1992 ASME B1.12-1987 ASME B18.18.1-2007 ASTM A193/A 193M-2008 ASTM A193/A 193M-2009 ASTM A307-2007 ASTM A354-2007 ASTM A380-2006 ASTM A449-2007 ASTM A967-2005 ASTM F468-2006 ASTM F593-2002 ASTM F788/F 788M-2008 ASTM F1
- 被代替标准
- SAE J 2271-2004
- 适用范围
- This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a. Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (0.190 through 4 inches); UNRF threads (0.190 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches) b. Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches); UNRF threads (1/4 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches); Different thread forms on each end are permissible. c. Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters; NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches); UNRC threads (1/4 through 4 inches) - UNRC threads (1/4 through 4 inches); UNRF threads (1/4 through 1-1/2 inches); UNRF threads (1/4 through 1-1/2 inches); 8UNR threads (1-1/8 through 4 inches); 8UNR threads (1-1/8 through 4 Inches) These studs are primarily for use in ship systems and equipment. The continuous thread studs and the reduced body diameter double end studs are configurations particularly suited to applications that are subject to high impact (H.I.) shock requirements.