DIN EN 13598-2-2009
无压力地下排水和排污用塑料管道系统 非增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE) 第2部分:交通范围和地下设施中检修孔和检查室用规范已作废

Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers in traffic areas and deep under

DIN EN 13598-2-2009 发布历史

This European Standard specifies the definitions and requirements for buried manholes and inspection chambers installed to a maximum depth of 6 m from ground level to the invert of the main chamber and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE). These products are intended for use in pedestrian or vehicular traffic areas and underground installations conforming to the general requirements given in EN 476 and are used outside the building structure (application area code "U"). They are therefore marked accordingly with a "U". Such products are also deemed to meet the requirements of EN 13598-1 for application area U without the need for further testing. If additionally marked application area D then these products must additionally be tested to show compliance to the elevated temperature cycling requirement of Clause 10 of EN 13598-1. This European Standard is only applicable to those chamber / manhole items where the manufacturer has clearly stated in the documentation how the components shall be assembled to create a complete manhole or inspection chamber. The inspection chambers covered by this European Standard comprise the following: -- inspection chambers providing access to the drainage or sewerage system by means of inspection and cleaning equipment. -- chambers, designated as manholes providing man access to the drainage or sewerage system. The inspection chamber / manhole can be manufactured by various methods e.g. injection moulding, rotational moulding, low-pressure moulding or fabricated from components made in accordance with other standards. The jointing of components can be achieved using: -- elastomeric ring seal joints; -- adhesive joints for PVC-U; -- welded joints for PVC-U, PP and PE; -- extrusion welding; -- mechanical jointing. NOTE Both manholes and inspection chambers can be site assembled from different components, but can also be manufactured as a single unit. In either case, the following functional parts can be recognized: a) base (always present) In case of a one-piece chamber or manhole, the base part ends at a distance of 300 mm measured from the top of the main channel; b) riser (depth dependent); c) telescopic part (design dependent); d) cone (dependent on the design of near surface components and their recommended installation); e) other near surface components.

DIN EN 13598-2-2009由德国标准化学会 DE-DIN 发布于 2009-04，于 2010-05 废止。

DIN EN 13598-2-2009 在中国标准分类中归属于: Q81 供水、排水器材设备，在国际标准分类中归属于: 93.030 外部污水排放系统。

DIN EN 13598-2-2009的历代版本如下：

• 2009年04月 DIN EN 13598-2-2009 无压力地下排水和排污用塑料管道系统 非增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE) 第2部分:交通范围和地下设施中检修孔和检查室用规范
• 2010年05月 DIN EN 13598-2-2010 无压力地下排水和排污用塑料管道系统.非增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).第2部分:交通区域和地下设施中检修孔和检查室用规范
• 2016年09月 DIN EN 13598-2-2016 无压力地下排水和排污用塑料管道系统.非增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).第2部分:检修孔和检查室用规范
• 2020年12月01日 DIN EN 13598-2-2020 用于非压力地下排水和污水处理的塑料管道系统. 未增塑的聚(氯乙烯)(PVC-U)、聚丙烯(PP)和聚乙烯(PE). 第2部分: 人孔和检查室规范; 德文版 EN 13598-2-2020

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 DIN EN 13598-2-2009 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

DIN EN 13598-2-2009

发布日期

2009年04月

实施日期

废止日期

2010-05

中国标准分类号

Q81

国际标准分类号

93.030

发布单位

DE-DIN

代替标准

DIN EN 13598-2-2010

适用范围

This European Standard specifies the definitions and requirements for buried manholes and inspection chambers installed to a maximum depth of 6 m from ground level to the invert of the main chamber and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE). These products are intended for use in pedestrian or vehicular traffic areas and underground installations conforming to the general requirements given in EN 476 and are used outside the building structure (application area code "U"). They are therefore marked accordingly with a "U". Such products are also deemed to meet the requirements of EN 13598-1 for application area U without the need for further testing. If additionally marked application area D then these products must additionally be tested to show compliance to the elevated temperature cycling requirement of Clause 10 of EN 13598-1. This European Standard is only applicable to those chamber / manhole items where the manufacturer has clearly stated in the documentation how the components shall be assembled to create a complete manhole or inspection chamber. The inspection chambers covered by this European Standard comprise the following: -- inspection chambers providing access to the drainage or sewerage system by means of inspection and cleaning equipment. -- chambers, designated as manholes providing man access to the drainage or sewerage system. The inspection chamber / manhole can be manufactured by various methods e.g. injection moulding, rotational moulding, low-pressure moulding or fabricated from components made in accordance with other standards. The jointing of components can be achieved using: -- elastomeric ring seal joints; -- adhesive joints for PVC-U; -- welded joints for PVC-U, PP and PE; -- extrusion welding; -- mechanical jointing. NOTE Both manholes and inspection chambers can be site assembled from different components, but can also be manufactured as a single unit. In either case, the following functional parts can be recognized: a) base (always present) In case of a one-piece chamber or manhole, the base part ends at a distance of 300 mm measured from the top of the main channel; b) riser (depth dependent); c) telescopic part (design dependent); d) cone (dependent on the design of near surface components and their recommended installation); e) other near surface components.

DIN EN 13598-2-2009系列标准