DIN EN 598-2009
污水处理应用球墨铸铁管,管件,配件及其接头.要求和试验方法,德文版本EN 598:2007+A1:2009

Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods(includes Amendment A1:2009); English version of DIN EN 598:2009-10

DIN EN 598-2009 发布历史

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes fittings, accessories and their joints for the construction of drains and sewers outside buildings: -- operating without pressure (gravity sewerage), or with positive or negative pressure (see Table 5); to be installed below or above ground; -- to convey surface water, domestic waste water and certain types of industrial effluents, either in separate systems or in combined systems. This European Standard applies to pipes, fittings and accessories which are: -- manufactured with socketed, flanged or spigot ends; -- normally delivered externally and internally coated; -- suitable for continuous fluid temperatures between 0 ℃ excluding frost, and 45 ℃ for DN ≤ 200 or 35 ℃ forv DN > 200, according to EN 476: -- not intended for use in areas subject to reaction to fire regulations NOTE 1 This does not preclude special arrangements for the products to be used at higher temperatures. This European Standard covers pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, of a size range extending from DN 80 to DN 2000 inclusive. This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this European Standard. NOTE 2 In this European Standard. all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

DIN EN 598-2009由德国标准化学会 DE-DIN 发布于 2009-10。

DIN EN 598-2009 在中国标准分类中归属于: Q81 供水、排水器材设备，在国际标准分类中归属于: 23.040.10 铁管和钢管,23.040.40 金属配件。

DIN EN 598-2009 发布之时，引用了标准

• EN 196-1 水泥试验方法-第1部分:强度的测定*， 2016-04-01 更新
• EN 545 水管线用球墨铸铁管,配件,附件机器连接件.试验方法和要求*， 2010-09-01 更新
• EN 681-1 弹性密封件.水和污水设施用管联接密封件的材料要求.第1部分:琉化橡胶.包含修改件A1-1998 和 A2-2002;合并勘误表-2002年8月;包含修改件A3-2005
• EN 1092-2 法兰及其连接.按PN标注的管,管件,异形件和附件用圆形法兰.第2部分:铸铁法兰
• EN 10002-1 金属材料.拉力试验.第1部分:环境温度的试验方法
• EN 14901 球墨铸铁管,装配及配件.球墨铸铁的装配及配件内的环氧尸涂层(重型).要求及测试方法*， 2014-10-01 更新
• EN ISO 4016 六角头螺栓.产品等级C级*， 2011-03-01 更新
• EN ISO 4034 定期六角螺母(款式1).C级产品*， 2022-07-23 更新
• EN ISO 6506-1 金属材料.布氏硬度试验.第1部分:试验方法(ISO 6506-1:2014)*， 2014-09-01 更新
• EN ISO 7091 平垫圈.标准系列.产品等级C ISO 7091-2000
• EN ISO 9001-2000 *， 2022-07-23 更新

* 在 DIN EN 598-2009 发布之后有更新，请注意新发布标准的变化。

DIN EN 598-2009的历代版本如下：

• 2008年01月 DIN EN 598-2008 排污设施用球墨铸铁管、管件、附件及连接件.要求和试验方法
• 2009年10月 DIN EN 598-2009 污水处理应用球墨铸铁管,管件,配件及其接头.要求和试验方法,德文版本EN 598:2007+A1:2009

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 DIN EN 598-2009 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

DIN EN 598-2009

发布日期

2009年10月

实施日期

废止日期

无

中国标准分类号

Q81

国际标准分类号

23.040.10;23.040.40

发布单位

DE-DIN

引用标准

EN 196-1 EN 545 EN 681-1 EN 1092-2 EN 10002-1 EN 14901 EN ISO 4016 EN ISO 4034 EN ISO 6506-1 EN ISO 7091 EN ISO 9001-2000

被代替标准

DIN EN 598-2008 DIN EN 598/A1-2009

适用范围

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes fittings, accessories and their joints for the construction of drains and sewers outside buildings: -- operating without pressure (gravity sewerage), or with positive or negative pressure (see Table 5); to be installed below or above ground; -- to convey surface water, domestic waste water and certain types of industrial effluents, either in separate systems or in combined systems. This European Standard applies to pipes, fittings and accessories which are: -- manufactured with socketed, flanged or spigot ends; -- normally delivered externally and internally coated; -- suitable for continuous fluid temperatures between 0 ℃ excluding frost, and 45 ℃ for DN ≤ 200 or 35 ℃ forv DN > 200, according to EN 476: -- not intended for use in areas subject to reaction to fire regulations NOTE 1 This does not preclude special arrangements for the products to be used at higher temperatures. This European Standard covers pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, of a size range extending from DN 80 to DN 2000 inclusive. This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this European Standard. NOTE 2 In this European Standard. all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

谁引用了DIN EN 598-2009 更多引用