IEC 61439-5-2010
低压开关设备和控制设备配件.第5部分:公共网络配电用配件

Low-voltage switchgear and controlgear assemblies.Part 5: Assemblies for power distribution in public networks

IEC 61439-5-2010 发布历史

This clause of Part 1 applies with the following additions. Addition: This standard gives specific requirements for public electricity network distribution assemblies (PENDAs), which are stationary assemblies verified by verification tests, as defined in this standard. These ASSEMBLIES are used for the distribution of electrical energy in three-phase systems (see Figure 101 for a typical distribution network). Open type ASSEMBLIES are not covered by this standard. The object of this standard is to state the definitions and to specify the service conditions, construction requirements, technical characteristics and tests for PENDAs. Network parameters may require tests at higher performance levels. NOTE 1 If a PENDA is equipped with additional equipment (for example meters), in such a way that the main function is changed considerably, then other standards may also apply as agreed between user and manufacturer (see 8.5). NOTE 2 Where local regulations and practices permit, a PENDA according to this standard may be used in other than public networks. PENDAs are suitable for installation in places where only skilled persons have access for their use, however, outdoor types may be installed in situations that are accessible to ordinary persons.

IEC 61439-5-2010由国际电工委员会 IX-IEC 发布于 2010-11-01，并于 2010-11-01 实施。

IEC 61439-5-2010 在中国标准分类中归属于: K30 低压电器综合，在国际标准分类中归属于: 29.130.20 低压开关装置和控制器。

IEC 61439-5-2010的历代版本如下：

• 2010年11月01日 IEC 61439-5-2010 低压开关设备和控制设备配件.第5部分:公共网络配电用配件
• 2014年08月01日 IEC 61439-5-2014 低压开关设备和控制设备配件.第5部分:公共网络配电用配件

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 IEC 61439-5-2010 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

IEC 61439-5-2010

发布日期

2010年11月01日

实施日期

2010年11月01日

废止日期

无

中国标准分类号

K30

国际标准分类号

29.130.20

发布单位

IX-IEC

代替标准

IEC 61439-5-2014

适用范围

This clause of Part 1 applies with the following additions. Addition: This standard gives specific requirements for public electricity network distribution assemblies (PENDAs), which are stationary assemblies verified by verification tests, as defined in this standard. These ASSEMBLIES are used for the distribution of electrical energy in three-phase systems (see Figure 101 for a typical distribution network). Open type ASSEMBLIES are not covered by this standard. The object of this standard is to state the definitions and to specify the service conditions, construction requirements, technical characteristics and tests for PENDAs. Network parameters may require tests at higher performance levels. NOTE 1 If a PENDA is equipped with additional equipment (for example meters), in such a way that the main function is changed considerably, then other standards may also apply as agreed between user and manufacturer (see 8.5). NOTE 2 Where local regulations and practices permit, a PENDA according to this standard may be used in other than public networks. PENDAs are suitable for installation in places where only skilled persons have access for their use, however, outdoor types may be installed in situations that are accessible to ordinary persons.

IEC 61439-5-2010系列标准

IEC 61439-5-2010 中可能用到的仪器设备

谁引用了IEC 61439-5-2010 更多引用