ISO/ASTM 51608-2005
辐射加工用X射线(韧致辐射)设备中放射剂量测定实施规程
Practice for dosimetry in an X-ray (Bremsstrahlung) facility for radiation processing
ISO/ASTM 51608-2005 发布历史
1 This practice outlines the installation qualification pro-gram for an X-ray (bremsstrahlung) irradiator and the dosim-etric procedures to be followed during operational qualifica-tion, performance qualification and routine processing to ensure that the entire product has been treated within a predetermined range of absorbed dose. Other procedures re-lated to operational qualification, performance qualification and routine processing that may influence absorbed dose in the product are also discussed. Information about effective or regulatory dose limits and energy limits for X-radiation is not within the scope of this practice. 2 In contrast to monoenergetic gamma radiation, the bremsstrahlung energy spectrum extends from low values (about 35 keV) up to the maximum energy of the electrons incident on the X-ray target (see Section 5 and Annex AI). 3 Dosimetry is only one component of a total quality assurance program for an irradiation facility. Other controls besides dosimetry may be required for specific applications, such as medical device sterilization and food preservation. 4 For the irradiation of food and the radiation sterilization of health care products, other specific ISO standards exist. For food irradiation, see ISO/ASTM Practice 51431. For the radiation sterilization of health care products, see ISO 11137. In those areas covered by ISO/ASTM Practice 51431 or ISO 11137, those standards take precedence. Note 1—For guidance in the selection, calibration, and use of specific dosimeters and interpretation of absorbed dose in the product from dose measurements, see the documents listed in Section 2. Note 2—Bremsstrahlung characteristics are similar to those of gamma radiation from radioactive nuclides. See ISO/ASTM Practices 51204 and 51702 for the applications of dosimetry in the characterization and operation of gamma irradiation facilities. For information concerning electron beam irradiation technology and dosimetry, see ISO/ASTM Practices 51431 and 51649. 5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.
ISO/ASTM 51608-2005由国际标准化组织 IX-ISO 发布于 2005-05。
ISO/ASTM 51608-2005 在中国标准分类中归属于: F80 核仪器与核探测器综合，在国际标准分类中归属于: 17.240 辐射测量。
ISO/ASTM 51608-2005的历代版本如下：
- 2002年03月 ISO/ASTM 51608-2002 辐射加工用X射线(韧致辐射)设备中放射剂量测定实施规程
- 2005年05月 ISO/ASTM 51608-2005 辐射加工用X射线(韧致辐射)设备中放射剂量测定实施规程
- 2015年03月 ISO/ASTM 51608-2015 在50 keV 和7.5 MeV 能量之间辐射加工用X射线(韧致辐射)设备中放射剂量测定实施规程
ISO/ASTM 51608-2005 辐射加工用X射线(韧致辐射)设备中放射剂量测定实施规程 由 ISO/ASTM 51608-2002 变更而来。
ISO/ASTM 51608-2005 辐射加工用X射线(韧致辐射)设备中放射剂量测定实施规程 于 2015-03 变更为 ISO/ASTM 51608-2015 在50 keV 和7.5 MeV 能量之间辐射加工用X射线(韧致辐射)设备中放射剂量测定实施规程。
- 标准号
- ISO/ASTM 51608-2005
- 发布日期
- 2005年05月
- 实施日期
- 废止日期
- 无
- 中国标准分类号
- F80
- 国际标准分类号
- 17.240
- 发布单位
- IX-ISO
- 代替标准
- ISO/ASTM 51608-2015
- 被代替标准
- ISO/ASTM 51608-2002 ISO/ASTM DIS 51608-2004
- 适用范围
- 1 This practice outlines the installation qualification pro-gram for an X-ray (bremsstrahlung) irradiator and the dosim-etric procedures to be followed during operational qualifica-tion, performance qualification and routine processing to ensure that the entire product has been treated within a predetermined range of absorbed dose. Other procedures re-lated to operational qualification, performance qualification and routine processing that may influence absorbed dose in the product are also discussed. Information about effective or regulatory dose limits and energy limits for X-radiation is not within the scope of this practice. 2 In contrast to monoenergetic gamma radiation, the bremsstrahlung energy spectrum extends from low values (about 35 keV) up to the maximum energy of the electrons incident on the X-ray target (see Section 5 and Annex AI). 3 Dosimetry is only one component of a total quality assurance program for an irradiation facility. Other controls besides dosimetry may be required for specific applications, such as medical device sterilization and food preservation. 4 For the irradiation of food and the radiation sterilization of health care products, other specific ISO standards exist. For food irradiation, see ISO/ASTM Practice 51431. For the radiation sterilization of health care products, see ISO 11137. In those areas covered by ISO/ASTM Practice 51431 or ISO 11137, those standards take precedence. Note 1—For guidance in the selection, calibration, and use of specific dosimeters and interpretation of absorbed dose in the product from dose measurements, see the documents listed in Section 2. Note 2—Bremsstrahlung characteristics are similar to those of gamma radiation from radioactive nuclides. See ISO/ASTM Practices 51204 and 51702 for the applications of dosimetry in the characterization and operation of gamma irradiation facilities. For information concerning electron beam irradiation technology and dosimetry, see ISO/ASTM Practices 51431 and 51649. 5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.