ASTM D4186/D4186M-12
用可控应变荷载测试饱和粘性土单维固结特性的标准试验方法

Standard Test Method for One-Dimensional Consolidation Properties of Saturated Cohesive Soils Using Controlled-Strain Loading

被代替

ASTM D4186/D4186M-12 发布历史

ASTM D4186/D4186M-12由美国材料与试验协会 US-ASTM 发布于 2012。

ASTM D4186/D4186M-12 在中国标准分类中归属于: P25 混凝土结构工程。

ASTM D4186/D4186M-12 用可控应变荷载测试饱和粘性土单维固结特性的标准试验方法的最新版本是哪一版？

最新版本是 ASTM D4186/D4186M-20e1 。

ASTM D4186/D4186M-12的历代版本如下：

• 2020年 ASTM D4186/D4186M-20e1 使用受控应变载荷的饱和粘性土的一维固结性能的标准测试方法
• 2020年 ASTM D4186/D4186M-20 使用受控应变载荷的饱和粘性土的一维固结性能的标准测试方法
• 2012年 ASTM D4186/D4186M-12e1 用可控应变荷载法的饱和性粘土的单向压实性能的标准试验方法
• 2012年 ASTM D4186/D4186M-12 用可控应变荷载测试饱和粘性土单维固结特性的标准试验方法
• 2006年 ASTM D4186-06 用可控应变荷载测试饱和粘性土单维固结性能的标准试验方法
• 1989年 ASTM D4186-89(1998)e1 使用受控应变载荷的饱和粘性土的一维固结性能的标准测试方法

 

5. Significance and UseTop Bottom

5.1 Information concerning magnitude of compression and rate-of-consolidation of soil is essential in the design of earth structures and earth supported structures. The results of this test method may be used to analyze or estimate one-dimensional settlements, rates of settlement associated with the dissipation of excess pore-water pressure, and rates of fluid transport due to hydraulic gradients. This test method does not provide information concerning the rate of secondary compression.

5.2 Strain Rate Effects:

5.2.1 It is recognized that the stress-strain results of consolidation tests are strain rate dependent. Strain rates are limited in this test method by specification of the acceptable magnitudes of the base excess pressure ratio during the loading phase. This specification provides comparable results to the 100 % consolidation (end of primary) compression behavior obtained using Test Method D2435.

5.2.2 Field strain rates vary greatly with time, depth below the loaded area, and radial distance from the loaded area. Field strain rates during consolidation processes are generally much slower than laboratory strain rates and cannot be accurately determined or predicted. For these reasons, it is not practical to replicate the field strain rates with the laboratory test strain rate.

5.3 Temperature Effects:

5.3.1 Temperature affects the rate parameters such as hydraulic conductivity and the coefficient of consolidation. The primary cause of temperature effects is due to the changes in pore fluid viscosity but soil sensitivity may also be important. This test method provides results under room temperature conditions, corrections may be required to account for specific field conditions. Such corrections are beyond the scope of this test method. Special accommodation maybe made to replicate field temperature conditions and still be in conformance with this test method.

5.4 Saturation Effects:

5.4.1 This test method may not be used to measure the properties of partially saturated soils because the method requires the material to be back pressure saturated prior to consolidation.

5.5 Test Interpretation Assumptions?/i>The equations used in this test method are based on the following assumptions:

5.5.1 The soil is saturated.

5.5.2 The soil is homogeneous.

5.5.3 The compressibility of the soil particles and water is negligible.

5.5.4 Flow of pore water occurs only..........

标准号

ASTM D4186/D4186M-12

发布

2012年

发布单位

美国材料与试验协会

替代标准

ASTM D4186/D4186M-12e1

当前最新

ASTM D4186/D4186M-20e1

 

 

ASTM D4186/D4186M-12相似标准

推荐

谁引用了ASTM D4186/D4186M-12 更多引用