CEN/TS 16637-2-2014
建筑产品.危险物质排放的评估.第2部分：水平动态表面浸取试验

Construction products - Assessment of release of dangerous substances - Part 2: Horizontal dynamic surface leaching test

CEN/TS 16637-2-2014 发布历史

(1) This Technical Specification specifies a Dynamic Surface Leaching Test (DSLT) which is aimed at determining the release per unit surface area as a function of time of inorganic and/or non-volatile organic substances from a monolithic, plate- or sheet-like product, when it is put into contact with an aqueous solution (leachant). The test method is not suitable for substances that are volatile under ambient conditions. (2) This test is a parameter specific test focusing on identifying and specifying parameter specific properties tested under specified conditions. It is not aimed at simulating real situations. The application of results to specific intended conditions of use may be established by means of modelling (not included in this Technical Specification). (3) The modification for granular construction products with low hydraulic conductivity (Annex A) applies for granular particles with so little drainage capacity between the grains that percolation in percolation tests and in practice is nearly impossible. (4) The test method applies to more or less regularly shaped test portions consisting of monolithic test pieces with minimum dimensions of 40 mm in all directions (volume > 64000 mm 3(64 cm 3 )). It also applies to plate- or sheet-like products with surface areas of minimum 10000 mm 2(100 cm 2 ) exposed to the leachant. Products designed to drain water (e. g. draining tiles, porous asphalt) and monolithic granular products according to CEN/TS 16637-1:2014, Table 1, are also tested by this test method. All products to be tested are assumed to maintain their integrity over a time frame relevant for the considered intended use. (5) Metals, metallic coatings and organic coatings on metals are excluded from the scope of CEN/TS 16637-2 because the principles of this test (diffusion) are not obeyed by these products. Guidance on the need for testing of these products is under consideration. (6) For some coatings (e. g. some renders with organic binders according

CEN/TS 16637-2-2014由欧洲标准化委员会 IX-CEN 发布于 2014-08。

CEN/TS 16637-2-2014 在中国标准分类中归属于: Z60 污染物排放综合，在国际标准分类中归属于: 13.040.20 环境空气,19.040 环境试验,91.100.01 建筑材料综合。

CEN/TS 16637-2-2014 发布之时，引用了标准

• EN 14346-2006 废弃物特征.通过测定干残渣或水含量计算干物质含量*， 2022-07-28 更新
• CEN/TS 15863-2012 废料的描述.浸出行为的测试基本的描述.与周期性leachant更新动态整体浸出试验,在固定的测试条件
• CEN/TR 16045-2010 建筑产品-评估释放有害物质管制的内容*， 2022-07-28 更新
• CEN/TR 16098-2010 建筑产品.危险物质的释放评估.水平测试程序下的持续专业发展支持的要求概念*， 2022-07-28 更新
• EN 16192-2011 废物特性描述.洗出液的分析*， 2022-07-28 更新
• CEN/TR 16496-2013 建筑产品.危险物质释放的评估.协调的横向评估方法的使用*， 2022-07-28 更新
• CEN/TS 16637-1-2014 建筑产品.危险物质排放的评估.第1部分：浸出试验和附加试验步骤的试验指南
• EN ISO 3696-1995 分析实验室用水.规范和试验方法(ISO 3696-1987)
• EN ISO 5667-3-2012 水质采样.第3部分:水样的保存和处理*， 2022-07-28 更新

* 在 CEN/TS 16637-2-2014 发布之后有更新，请注意新发布标准的变化。

CEN/TS 16637-2-2014的历代版本如下：

• 2014年08月 CEN/TS 16637-2-2014 建筑产品.危险物质排放的评估.第2部分：水平动态表面浸取试验

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 CEN/TS 16637-2-2014 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

CEN/TS 16637-2-2014

发布日期

2014年08月

实施日期

废止日期

无

中国标准分类号

Z60

国际标准分类号

13.040.20;19.040;91.100.01

发布单位

IX-CEN

引用标准

EN 14346-2006 CEN/TS 15863-2012 CEN/TR 16045-2010 CEN/TR 16098-2010 EN 16192-2011 CEN/TR 16496-2013 CEN/TS 16637-1-2014 FprCEN/TS 16637-3 EN ISO 3696-1995 EN ISO 5667-3-2012 EA NEN 7375-2005

被代替标准

FprCEN/TS 16637-2-2013

适用范围

(1) This Technical Specification specifies a Dynamic Surface Leaching Test (DSLT) which is aimed at determining the release per unit surface area as a function of time of inorganic and/or non-volatile organic substances from a monolithic, plate- or sheet-like product, when it is put into contact with an aqueous solution (leachant). The test method is not suitable for substances that are volatile under ambient conditions. (2) This test is a parameter specific test focusing on identifying and specifying parameter specific properties tested under specified conditions. It is not aimed at simulating real situations. The application of results to specific intended conditions of use may be established by means of modelling (not included in this Technical Specification). (3) The modification for granular construction products with low hydraulic conductivity (Annex A) applies for granular particles with so little drainage capacity between the grains that percolation in percolation tests and in practice is nearly impossible. (4) The test method applies to more or less regularly shaped test portions consisting of monolithic test pieces with minimum dimensions of 40 mm in all directions (volume > 64000 mm 3(64 cm 3 )). It also applies to plate- or sheet-like products with surface areas of minimum 10000 mm 2(100 cm 2 ) exposed to the leachant. Products designed to drain water (e. g. draining tiles, porous asphalt) and monolithic granular products according to CEN/TS 16637-1:2014, Table 1, are also tested by this test method. All products to be tested are assumed to maintain their integrity over a time frame relevant for the considered intended use. (5) Metals, metallic coatings and organic coatings on metals are excluded from the scope of CEN/TS 16637-2 because the principles of this test (diffusion) are not obeyed by these products. Guidance on the need for testing of these products is under consideration. (6) For some coatings (e. g. some renders with organic binders according

谁引用了CEN/TS 16637-2-2014 更多引用