ASTM D698-12e2由美国材料与试验协会 US-ASTM 发布于 2012。
ASTM D698-12e2在国际标准分类中归属于: 93.020 土方工程、挖掘、地基构造、地下工程。
* 在 ASTM D698-12e2 发布之后有更新,请注意新发布标准的变化。
5.1 Soil placed as engineering fill (embankments, foundation pads, road bases) is compacted to a dense state to obtain satisfactory engineering properties such as, shear strength, compressibility, or permeability. In addition, foundation soils are often compacted to improve their engineering properties. Laboratory compaction tests provide the basis for determining the percent compaction and molding water content needed to achieve the required engineering properties, and for controlling construction to assure that the required compaction and water contents are achieved.
5.2 During design of an engineered fill, shear, consolidation, permeability, or other tests require preparation of test specimens by compacting at some molding water content to some unit weight. It is common practice to first determine the optimum water content (wopt) and maximum dry unit weight (γd,max) by means of a compaction test. Test specimens are compacted at a selected molding water content (w), either wet or dry of optimum (wopt) or at optimum (wopt), and at a selected dry unit weight related to a percentage of maximum dry unit weight (γd,max). The selection of molding water content (w), either wet or dry of optimum (wopt) or at optimum (wopt) and the dry unit weight (γd,max) may be based on past experience, or a range of values may be investigated to determine the necessary percent of compaction.
5.3 Experience indicates that the methods outlined in 5.2 or the construction control aspects discussed in 5.1 are extremely difficult to implement or yield erroneous results when dealing with certain soils. 5.3.1 – 5.3.3 describe typical problem soils, the problems encountered when dealing with such soils and possible solutions for these problems.
5.3.1 Oversize Fraction—Soils containing more than 308201;% oversize fraction (material retained on the 3/4-in. (19-mm) sieve) are a problem. For such soils, there is no ASTM test method to control their compaction and very few laboratories are equipped to determine the laboratory maximum unit weight (density) of such soils (USDI Bureau of Reclamation, Denver, CO and U.S. Army Corps of Engineers, Vicksburg,......
相比传统的测量方法(灌砂法,灌水法,环刀法,钻芯法等),大大减少了试验人员的工具配置和试验量,避免了传统方法冗杂的测量工具,SDG200充分发挥了其小巧方便的优势。SDG200主机外观图功能全面SDG200土壤无核密度仪既可以测量室内土工击实的标准土件的压实度,也可以测量室外施工过程中碾压土层的现场压实度。...
与Transtech公司专家技术交流江苏、福建的检测、研究单位正积极推进地方土壤压实度规范的建立,本次会议中厂家和参会专家就SDG技术原理、计算模型方程等问题充分交流之后达成一致:厂家近期将给出试验方法与需求数据清单,国内客户根据照厂家的要求使用国内有代表性的土壤完成一系列试验后,将试验数据反馈厂家,厂家将针对国内土壤特性,修改SDG计算模型,增强SDG在国内适用性。...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号