IEC 61730-1-2016
光电(PV)组件安全性鉴定.第1部分:构造要求
Photovoltaic (PV) module safety qualification - Part 1: Requirements for construction
IEC 61730-1-2016 发布历史
This part of IEC 61730 specifies and describes the fundamental construction requirements for photovoltaic (PV) modules in order to provide safe electrical and mechanical operation. Specific topics are provided to assess the prevention of electrical shock, fire hazards, and personal injury due to mechanical and environmental stresses. This part of IEC 61730 pertains to the particular requirements of construction. IEC 61730-2 defines the requirements for testing. This International Standard series lays down IEC requirements of terrestrial photovoltaic modules suitable for long-term operation in open-air climates. This standard is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. PV modules covered by this standard are limited to a maximum DC system voltage of 1500 V. This International Standard defines the basic requirements for various applications of PV modules, but it cannot be considered to encompass all national or regional codes. Specific requirements, e. g. for building, marine and vehicle applications, are not covered. This International Standard does not address specific requirements for products that combine a PV module with power conversion equipment, monitoring or control electronics, such as integrated inverters, converters or output disabling functions. While parts of this standard may be applicable to flat plate PV modules with internally generated low level concentration below 3 times, it was not written specifically to address these concerns. This International Standard is designed to coordinate with the test sequences in the IEC 61215 series, so that a single set of samples may be used to perform both the safety and qualification of a photovoltaic module design. The object of this International Standard is to define the requirements for the construction of photovoltaic modules with respect to safety. These requirements are intended to minimize the misapplication and misuse of PV modules or the failure of their components which could result in fire, electric shock and personal injury. Additional construction requirements outlined in relevant ISO standards, or the national or local codes which govern the installation and use of these PV modules in their intended locations, should be considered in addition to the requirements contained within this standard.
IEC 61730-1-2016由国际电工委员会 IX-IEC 发布于 2016-08。
IEC 61730-1-2016 在中国标准分类中归属于: L54 半导体光敏器件,F12 太阳能，在国际标准分类中归属于: 27.160 太阳能工程。
IEC 61730-1-2016 发布之时，引用了标准
- EN 50618-2014
- IEC 60050-55-1970 国际电工词汇.第55章:电报和电话
- IEC 60050-101-1998 国际电工词汇 第101部分:数学
- IEC 60050-102-2007 国际电工词汇.第102部分:数学.一般概念和线性代数
- IEC 60050-103-2009 International Electrotechnical Vocabulary – Part 103: Mathematics – Functions (Edition 1.0)
- IEC 60050-111-1996 国际电工词汇 第111章:物理和化学
- IEC 60050-111 AMD 1-2005 修改件1.国际电工词汇.第111章:物理和化学
- IEC 60050-112-2010 International Electrotechnical Vocabulary – Part 112: Quantities and units (Edition 1.0)
- IEC 60050-113-2011 国际电工词汇.第113部分:电工学用物理现象
- IEC 60050-113 CORR 1-2011 CORRIGENDUM 1 Vocabulaire Electrotechnique International – Partie 113: Physique pour l’électrotechnique (Edition 1.0)
- IEC 60050-113 AMD 1-2014 AMENDEMENT 1 Vocabulaire Electrotechnique International – Partie 113: Physique pour l’électrotechnique (Edition 1.0)
- IEC 60050-114-2014 国际电工词汇. 第114部分: 电化学
- IEC 60050-121-1998 国际电工词汇 第121部分:电磁学
- IEC 60050-121 AMD 1-2002 国际电工词汇.第121部分:电磁学.修改件1
- IEC 60050-121 AMD 2-2008 国际电工词汇.第121部分:电磁学
- IEC 60050-131-2002 国际电工词汇.第131部分:电路理论
- IEC 60050-131 AMD 1-2008 国际电工词汇.第131部分:电路理论.修改件1
- IEC 60050-131 AMD 2-2013 国际电工词汇.第131部分:电路理论
- IEC 60050-141-2004 电工术语.第141部分:多相系统与多相电路
- IEC 60050-151-2001 国际电工词汇 第151部分：电和磁的器件
- IEC 60050-151 AMD 1-2013 国际电工词汇.第151部分:电气和磁性器件.修改件1
- IEC 60050-151 AMD 2-2014 AMENDEMENT 2 Vocabulaire Electrotechnique International Partie 151: Dispositifs électriques et magnétiques (Edition 2.0)
- IEC 60050-161-1990 国际电工词汇 第161章:电磁兼容性
- 110
IEC 61730-1-2016的历代版本如下：
- 2004年10月 IEC 61730-1-2004 光电(PV)模件安全合格鉴定.第1部分:施工要求
- 2011年11月14日 IEC 61730-1-2004/AMD1-2011 修改件1.光伏（PV）组件安全鉴定.第1部分:施工要求
- 2013年03月14日 IEC 61730-1-2004/AMD2-2013 修改件2.光伏（PV）组件安全鉴定.第1部分:施工要求
- 2013年03月01日 IEC 61730-1-2013 Photovoltaic (PV) module safety qualification – Part 1: Requirements for construction (Edition 1.2 Consolidated Reprint)
- 2016年08月 IEC 61730-1-2016 光电(PV)组件安全性鉴定.第1部分:构造要求
- 标准号
- IEC 61730-1-2016
- 发布日期
- 2016年08月
- 实施日期
- 废止日期
- 无
- 中国标准分类号
- L54;F12
- 国际标准分类号
- 27.160
- 发布单位
- 国际电工委员会
- 引用标准
- EN 50618-2014 IEC 60050-55-1970 IEC 60050-101-1998 IEC 60050-102-2007 IEC 60050-103-2009 IEC 60050-111-1996 IEC 60050-111 AMD 1-2005 IEC 60050-112-2010 IEC 60050-113-2011 IEC 60050-113 CORR 1-2011 IEC 60050-113 AMD 1-2014 IEC 60050-114-2014 IEC 60050-121-1998 IEC 60050-121 AMD 1-2002 IEC 60050-121 AMD 2-2008 IEC 60050-131-2002 IEC 60050-131 AMD 1-2008 IEC 60050-131 AMD 2-2013 IEC 60050-141-2004 IEC 60050-151-2001 IEC 60050-151 AMD 1-2013 IEC 60050-151 AMD 2-2014 IEC 60050-161-1990 IEC 60050-161
- 被代替标准
- IEC 82/1128/FDIS-2016 IEC 61730-1-2004 IEC 61730-1 AMD 1-2011 IEC 61730-1 AMD 2-2013 IEC 61730-1 Edition 1.2-2013
- 适用范围
- This part of IEC 61730 specifies and describes the fundamental construction requirements for photovoltaic (PV) modules in order to provide safe electrical and mechanical operation. Specific topics are provided to assess the prevention of electrical shock, fire hazards, and personal injury due to mechanical and environmental stresses. This part of IEC 61730 pertains to the particular requirements of construction. IEC 61730-2 defines the requirements for testing. This International Standard series lays down IEC requirements of terrestrial photovoltaic modules suitable for long-term operation in open-air climates. This standard is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. PV modules covered by this standard are limited to a maximum DC system voltage of 1500 V. This International Standard defines the basic requirements for various applications of PV modules, but it cannot be considered to encompass all national or regional codes. Specific requirements, e. g. for building, marine and vehicle applications, are not covered. This International Standard does not address specific requirements for products that combine a PV module with power conversion equipment, monitoring or control electronics, such as integrated inverters, converters or output disabling functions. While parts of this standard may be applicable to flat plate PV modules with internally generated low level concentration below 3 times, it was not written specifically to address these concerns. This International Standard is designed to coordinate with the test sequences in the IEC 61215 series, so that a single set of samples may be used to perform both the safety and qualification of a photovoltaic module design. The object of this International Standard is to define the requirements for the construction of photovoltaic modules with respect to safety. These requirements are intended to minimize the misapplication and misuse of PV modules or the failure of their components which could result in fire, electric shock and personal injury. Additional construction requirements outlined in relevant ISO standards, or the national or local codes which govern the installation and use of these PV modules in their intended locations, should be considered in addition to the requirements contained within this standard.