DIN ISO 10816-4-2018
机械振动.通过固定组件测量值估测机械振动.第4部分:带流体膜轴承的燃气汽轮机组(ISO 10816-4-2009+Amd.1-2017)

Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 4: Gas turbine sets with fluid-film bearings (ISO 10816-4:2009 + Amd.1:2017)

DIN ISO 10816-4-2018 发布历史

This standard provides specific guidance for assessing the severity of radial vibration measured on the bearing housings of gas turbines with fluid-film bearings in situ. The criteria provided in this document apply to heavy-duty gas turbine sets used in electrical and mechanical drive applications, with outputs greater than 3 MW and a speed range under load between 3 000 r/min and 30 000 r/min. This includes gas turbines coupled to other rotating machinery either directly or through a gearbox. Two criteria are provided for assessing the machine vibration when operating under steady state conditions. One criterion considers the magnitude of the observed vibration; the second considers changes in the magnitude. In addition, different criteria are provided for transient operating conditions, such as run-up and coast-down. The evaluation procedures presented in this part of ISO 10816 are based on broad-band measurements. This part of ISO 10816 is not applicable to the following: a) aero-derivative gas turbines (including gas turbines with dynamic properties similar to those of aero-derivatives); b) gas turbines with outputs greater than 40 MW and with rated speeds of 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (see ISO 20816-2); c) gas turbines with outputs less than or equal to 3 MW (see ISO 10816-3); d) gas turbine driven rotodynamic pumps (see ISO 10816-7); e) coupled steam turbines and/or generators with outputs less than or equal to 40 MW (see ISO 10816-3); f) coupled steam turbines and/or generators with outputs greater than 40 MW and speeds of 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (see ISO 20816-2); g) coupled steam turbines and/or generators with outputs greater than 40 MW and speeds other than 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (although generators seldom fall into this category) (see ISO 10816-3); h) synchronizing clutches which couple the gas turbine to a steam turbine or generator (see ISO 20816-2); i) coupled rotary compressor

DIN ISO 10816-4-2018由德国标准化学会 DE-DIN 发布于 2018-01-00。

DIN ISO 10816-4-2018 在中国标准分类中归属于: Z32 噪声、振动测试方法，在国际标准分类中归属于: 17.160 振动、冲击和振动测量。

DIN ISO 10816-4-2018 发布之时，引用了标准

• DIN ISO 2954-2012 旋转式和往复式机器的机械振动.对测量振动烈度仪器的要求(ISO 2954-2012)
• DIN ISO 5348-1999 机械振动和冲击.加速计的机械安装
• DIN ISO 7919-3-2009 机械振动.采用旋转轴测量机械振动的评定.第3部分:啮合连接工业机械(ISO 7919-3-2009)
• DIN ISO 7919-4-2010 机械振动.通过转轴测量值估测机械振动.第4部分:带流体膜轴承的燃气汽轮机组(ISO 7919-4-2009)
• DIN ISO 10816-3-2009 机械振动.对非旋转部件进行测量以评定机械振动.第3部分:现场测量时额定功率在15kW之上、额定速度在120r/min和15000r/min之间的工业机械(ISO 10816-3-2009)
• DIN ISO 10816-7-2009 机械振动.通过对非旋转部件的测量评定机械振动.第7部分:包括在旋转轴上测量的工业设施用旋转动力泵(ISO 10816-7:2009),英文版本DIN ISO 10816-7:2009-08
• DIN ISO 13373-1-2002 机械设备的条件监测和诊断.振动条件监测.第1部分:一般程序 (ISO 13373-1:2002)
• DIN ISO 13373-2-2016 机器的工况监测和诊断.振动条件监测.第2部分:振动数据的处理、分析和表示(ISO 13373-2-2016)
• DIN ISO 13373-3-2015 机器的工况监测和诊断. 振动状态监测. 第3部分: 振动诊断指南 (ISO 13373-3-2015)
• DIN ISO 20816-1-2017 机械振动.机械振动的测量和评估.第1部分:通用指南(ISO 20816-1-2016)
• DIN ISO 21940-12-2016 机械振动.转子平衡.第12部分:柔性转子的规程和公差(ISO 21940-12-2016)
• DIN ISO 21940-13-2012 机械振动.转子平衡.第13部分:中型和大型转子就地平衡用安全保护和准则(ISO 21940-13-2012)
• ISO 2041-2009 机械振动,冲击和状态监测.词汇
• ISO 2954-2012 旋转式和往复式机器的机械振动 对测量振动烈度仪器的要求
• ISO 3977-3-2004 燃气轮机.采购.第3部分:设计要求
• ISO 5348-1998 机械振动与冲击 加速计的机械安装
• ISO 7919-4-2009 机械振动.通过在旋转轴上的测量评价机械振动.第4部分:带有流体膜轴承的燃气轮机组
• ISO 10816-3-2009 机械振动.通过非转动件的测量进行机械振动的评估.第3部分:现场测量时标称功率为15kW和标称速度为120r/min～15000r/min的工业机械
• ISO 10816-7-2009 机械振动.通过在非旋转部件上测量评估机器振动.第7部分:包括在旋转轴上测量的工业设施用旋转动力泵
• ISO 13373-1-2002 条件监测和机械诊断.振动条件监测.第1部分:一般程序
• ISO 13373-2-2016 机器的工况监测和诊断.振动条件监测.第2部分:振动数据的处理、分析和表示
• ISO 13373-3-2015 机器的工况监测和诊断. 振动状态监测. 第3部分: 振动诊断指南
• ISO 20816-1-2016 机械振动. 机械振动的测量和评估. 第1部分: 通用指南
• ISO 20816-2-2017 机械振动. 机械振动的测量和评估. 第2部分：陆基燃气轮机、蒸汽轮机和超过40mw的发电机，带有油膜轴承，额定转速为1500 r / min、1800 r / min、3000 r / min和3600 r / min

DIN ISO 10816-4-2018的历代版本如下：

• 2010年06月 DIN ISO 10816-4-2010 机械振动.通过固定组件测量值估测机械振动.第4部分:带流体膜轴承的燃气汽轮机组(ISO 10816-4-2009)
• 2018年01月 DIN ISO 10816-4-2018 机械振动.通过固定组件测量值估测机械振动.第4部分:带流体膜轴承的燃气汽轮机组(ISO 10816-4-2009+Amd.1-2017)

DIN ISO 10816-4-2018 于 2018-10-00 变更为 DIN ISO 20816-4-2018 机械振动. 机械振动的测量和评估. 第4部分: 带有流体膜轴承的超过3MW的燃气轮机(ISO 20816-4-2018)。

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 DIN ISO 10816-4-2018 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

DIN ISO 10816-4-2018

发布日期

2018年01月

实施日期

废止日期

无

中国标准分类号

Z32

国际标准分类号

17.160

发布单位

DE-DIN

引用标准

DIN ISO 2954-2012 DIN ISO 5348-1999 DIN ISO 7919-3-2009 DIN ISO 7919-4-2010 DIN ISO 10816-3-2009 DIN ISO 10816-7-2009 DIN ISO 13373-1-2002 DIN ISO 13373-2-2016 DIN ISO 13373-3-2015 DIN ISO 20816-1-2017 DIN ISO 20816-2-2016 DIN ISO 21940-12-2016 DIN ISO 21940-12 Beiblatt 1-2015 DIN ISO 21940-13-2012 ISO 2041-2009 ISO 2954-2012 ISO 3977-3-2004 ISO 5348-1998 ISO 7919-4-2009 ISO 10816-3-2009 ISO 10816-7-2009 ISO 13373-1-2002 ISO 13373-2-2016 ISO 13373-3-2015 ISO 20816-1-2016 ISO 20816-2-2017 ISO 219

代替标准

DIN ISO 20816-4-2018

被代替标准

DIN ISO 10816-4-2010 DIN ISO 10816-4/A1-2016

适用范围

This standard provides specific guidance for assessing the severity of radial vibration measured on the bearing housings of gas turbines with fluid-film bearings in situ. The criteria provided in this document apply to heavy-duty gas turbine sets used in electrical and mechanical drive applications, with outputs greater than 3 MW and a speed range under load between 3 000 r/min and 30 000 r/min. This includes gas turbines coupled to other rotating machinery either directly or through a gearbox. Two criteria are provided for assessing the machine vibration when operating under steady state conditions. One criterion considers the magnitude of the observed vibration; the second considers changes in the magnitude. In addition, different criteria are provided for transient operating conditions, such as run-up and coast-down. The evaluation procedures presented in this part of ISO 10816 are based on broad-band measurements. This part of ISO 10816 is not applicable to the following: a) aero-derivative gas turbines (including gas turbines with dynamic properties similar to those of aero-derivatives); b) gas turbines with outputs greater than 40 MW and with rated speeds of 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (see ISO 20816-2); c) gas turbines with outputs less than or equal to 3 MW (see ISO 10816-3); d) gas turbine driven rotodynamic pumps (see ISO 10816-7); e) coupled steam turbines and/or generators with outputs less than or equal to 40 MW (see ISO 10816-3); f) coupled steam turbines and/or generators with outputs greater than 40 MW and speeds of 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (see ISO 20816-2); g) coupled steam turbines and/or generators with outputs greater than 40 MW and speeds other than 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (although generators seldom fall into this category) (see ISO 10816-3); h) synchronizing clutches which couple the gas turbine to a steam turbine or generator (see ISO 20816-2); i) coupled rotary compressor

DIN ISO 10816-4-2018系列标准