共找到 1232 条与 报警和警告系统 相关的标准,共 83 页
Alarm systems — Intrusion and hold-up systems — Part 2-4: Intrusion detectors — Combined passive infrared/Microwave detectors
Alarm systems — Intrusion and hold-up systems — Part 2-2: Intrusion detectors ― Passive infrared detectors
1 Scope This document specifies the requirements for pyrotechnic obscuration security devices as a part of an IAS. It covers application and performance and specifies the necessary tests and trials to ensure efficiency and reliability of such obscuration devices. This document is not intended to cover Hold-up alarm systems, standalone or vehicular security pyrotechnic obscuration security device . This document also gives guidelines on the criteria for design, installation, operation and maintenance of security pyrotechnic obscuration security device . NOTE This document does not deal with CE marking, chemical (REACH/CLP) or transport regulation requirements for pyrotechnical devices set forth in the relevant European regulation and harmonized standards issued for this purpose.
Alarm systems. Intrusion and hold-up systems - Pyrotechnic Obscuration Security Devices
重复性:±1.0%FS(测量成分、量程)线性度:±1.0%FS(测量成分、量程) 零点漂移:±1.0%FS/6个月(测量成分、量程) 其它气体干涉:在测量波长范围内没有吸收的气体原则上无干涉响应时间 (90%FS 响应) lt;5秒 预热时间:30分钟以内 分析方法:基于特征波长选择性吸收原理的 仪用空气要求:0.4-0.7MPa 警报输出:气体温度设定范围以外、仪表气低压异常、盒罩内温度异常输出信号型式:4-20mA
General technical specifications for single-end plug-in ammonia on-line monitoring system
Workplace atmospheres – Part 2: Gas detectors – Selection, installation, use and maintenance of detectors for toxic gases and vapours
Alarm systems - Intrusion and hold-up systems - Part 13: Pyrotechnic Obscuration Security Devices (german version)
This part of IEC 60839 defines the Web services interface for electronic access control systems. This includes listing electronic access control system components, their logical composition, monitoring their states and controlling them. It also includes a mapping of mandatory and
Alarm and electronic security systems - Part 11-33: Electronic access control systems - Access control configuration based on Web services
This document is for combined passive infrared and microwave detectors installed in buildings and provides for security Grades 1 to 4 (see EN 50131-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see EN 50130-5). This document do
Alarm systems - Intrusion and hold-up systems - Part 2-4: Requirements for combined passive infrared and microwave detectors; German version EN 50131-2-4:2020
Processing of alarm signals by an alarm receiving centre. Code of practice
Alarm systems - Alarm transmission systems and equipment - Part 3: Requirements for Receiving Centre Transceiver (RCT)
Alarm systems. Social alarm systems. Interconnections and communications
IEC 62642-2-71:2015 defines passive acoustic glass break detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
Alarm systems - Intrusion and hold-up systems - Part 2-71: Intrusion detectors - Glass break detectors (acoustic)
IEC 60839-11-31:2016 defines procedures for communication between network clients and devices. This series of interoperability standards makes it possible to build an alarm and electronic security system with clients and devices from different manufacturers using common and well defined interfaces. The functions defined in this document covers discovery, device management and event framework. Supplementary dedicated services are defined in separate documents. The management and control interfaces defined in this document are described as Web services. This document also contains full XML schema and Web Service Description Language (WSDL) definitions. In order to offer full plug-and-play interoperability, this document defines procedures for device discovery. The device discovery mechanisms in this document are based on the WS-Discovery specification with extensions.
Alarm and electronic security systems - Part 11-31: Electronic access control systems - Core interoperability protocol based on Web services
Gas detectors - Electrical apparatus for the detection of carbon monoxide in domestic premises - Part 1: Test methods and performance requirements (Corrigendum) (german version)
IEC 62642-2-73:2015 defines active surface mounted glass break detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
Alarm systems - Intrusion and hold-up systems - Part 2-73: Intrusion detectors - Glass break detectors (active)
IEC 60839-11-32:2016 defines the Web services interface for electronic access control systems. This includes listing electronic access control system components, their logical composition, monitoring their states and controlling them. It also includes a mapping of mandatory and optional requirements as per IEC 60839-11-1. This document applies to physical security only. Physical security prevents unauthorized personnel, attackers or accidental intruders from physically accessing a building, room, etc. Web services usage and device management functionality are outside of the scope of this document. Refer to IEC 60839-11-31 for more information.
Alarm and electronic security systems - Part 11-32: Electronic access control systems - Access control monitoring based on Web services
IEC 62820-3-2:2018 describes the basic application requirements for Advanced Security Building Intercom Systems (ASBIS) in public and private buildings with advanced safety and security needs. ASBIS are also used to meet the requirements of the Local Regulations of Workplace Safety and/or other relevant local regulations, in particular, protecting the life and limb of employees and all persons in the building, taking into account the inclusion of people with disabilities (e.g to achieve barrier-free access or calls for help) where required by local applicable law. The recommendations and requirements of IEC 62820-3-1 are mandatory for this document.
Building intercom systems - Part 3-2: Application guidelines - Advanced security building intercom systems (ASBIS)
IEC 62820-3-1:2017 gives guidelines for planning, installation, commissioning, operation and maintenance of Building Intercom Systems (BIS), for use in security applications. The different technical requirements for BIS are specified in IEC 62820-1-1 and IEC 62820-1-2. The objectives of this document are to: - provide a framework to assist system integrators, installers, consultant engineers and system owners in establishing their requirements; - assist specifiers and system owners in determining the appropriate equipment required for a given application.
Building intercom systems - Part 3-1: Application guidelines - General
IEC 62820-1-1:2016 specifies the technical requirements for the composition, functions, performance, and test methods of general building intercom systems. This part is applicable to the general intercom systems for building entry in residential or commercial buildings. General building intercom systems have been classified into two grades: Grade 1 adopts lower requirements to cover door-entry-systems not used for relevant security applications while grade 2 adopts higher requirements for building intercom systems for security applications. Each grade may adopt different functional and performance requirements, test methods and normative references.
Building intercom systems - Part 1-1: System requirements - General
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号