17.080 时间、速度、加速度、角速度的测量 标准查询与下载

GEIA-859-2004 数据管理

Data is information (e.g., concepts, thoughts, opinions) that has been recorded in a form that is convenient to move or process. Data can be tables of values of various types (numbers, characters, and so on). Data can also take more complex forms such a

Data Management

ANSI/IEEE 1293:2003 线性、单轴、无回旋装置加速度计的标准规范格式指南和试验规程

Defines the requirements for a linear, single-axis, nongyroscopic accelerometer. Defines not only the performance requirements of an inertial accelerometer as a unique device, but also its specific variational but repeatable and predictable performance parameters.

Standard Specification Format Guide and Test Procedure for Linear, Single-Axis, Nongyroscopic Accelerometers

GOST 8.577-2002 国家测量统一性保证体系.实体角位移线性加速度及平面角测定方法的国家鉴定程序

State system for ensuring the uniformity of measurements. State verification schedule for means measuring linear accelerations and plane angle for angle displacement of a solid body

AIR FORCE MS27573 REV A VALID NOTICE 4-2000 航空器凸缘架集油槽2 3/4英寸刻度盘仪器药筒

LASE, INSTRUMENT, 2 % WCB DIAL, WITH SUMP, FLANGE MOUN'I'EU, AIKCRAFT MS27573A remains inactive for new design, however the document is valid for acquisition whenneeded.Custodians:Amy - AV Air Force-99 AMSC N/A Preparing Activity.

CASE, INSTRUMENT, 2 3/4 INCH DIAL, WITH SUMP, FLANGE MOUNTED, AIRCRAFT

GOST 8.129-1999 时间和频率测量器具的国家检定系统

Настоящий стандарт распространяется на государственную поверочную схему для средств измерений времени и частоты и устанавливает порядо

State system for ensuring the uniformity of measurements. State verification schedule for means measuring time and frequency

IEEE 1139-1999 基本频率和时间计量学用物理量定义.随机不稳定性

Affects all documents dealing with the reporting or specification of time and frequency measurements and instrumentation.

Definitions of physical quantities for fundamental frequency and time metrology - Random instabilities

GEIA CMB7-4-1998 词汇,缩略语和定义取代 CMB4-1A-1984 标准

This standard applies to the interconnection of data terminal equipment and numerical control equipment at the tape reader interface. The data terminal would typically be connected to a remote data source/sink such as a computer.

Glossary of Terms, Acronyms and Definitions Supersedes CMB4-1A: 1984

IEEE 1293-1998 线性,单轴,非磁化加速仪试验规程和格式指南

Defines the requirements for a linear, single-axis, nongyroscopic accelerometer. Defines not only the performance requirements of an inertial accelerometer as a unique device, but also its specific variational but repeatable and predictable performance parameters.

Format guide and test procedure for linear, single-axis, nongyroscopic accelerometers

GEIA SP3893-1997 基本控制语言ASCII码的数据交换规范计算机数值控制的制造评论期届满

This standard applies to the interconnection of data terminal equipment and numerical control equipment at the tape reader interface. The data terminal would typically be connected to a remote data source/sink such as a computer.

Basic Control Language (BCL) an ASCII Data Exchange Specification for Computer Numerical Control Manufacturing Comment Period Expires: May 21, 1997; EIA-494-C

GEIA EIA-554 SET-1996 PPM非协调水平评估的方法选择

This standard applies to the interconnection of data terminal equipment and numerical control equipment at the tape reader interface. The data terminal would typically be connected to a remote data source/sink such as a computer.

Method Selection for Assessment of Nonconforming Levels in Parts per Million (PPM) - Includes EIA-554-1, EIA-554-2, and EIA-554-A

GEIA EIA-681-1996 进程识别评估指南

The focus of process certification is on the collectioonf processes that combinet o produce products and services to the customer’s satisfaction.

Assessment Guide for Process Certification

GEIA CMB6-6-1996 组态稽核

What are technical reviews and audits? The technical reviews (sometimes referred to as design reviews) and product audits described in this text are conducted to help ensure a controlled evolution of the product from its conceptual to production phase.

Reviews and Configuration Audits

AIR FORCE MS27573 REV A NOTICE 3-1996 航空器凸缘架集油槽2 3/4英寸刻度盘仪器药筒

This notice should be filed in front of MS27573A dated 19 November 1968.

CASE, INSTRUMENT, 2 3/4 INCH DIAL, WITH SUMP, FLANGE MOUNTED, AIRCRAFT

ASTM F1416-96(2008) 时间.温度指示器的选择的标准指南

Expiration dates are often marked on the packages of perishable products to indicate the presumed end of their shelf lives. Since the shelf lives of most perishable products are temperature dependent, the expiration date is determined by assuming the product will be kept within a prescribed temperature range for its entire life. A problem with this method is that there is no way to determine if the shelf life of a product has been shortened by exposure to a higher temperature. A time-temperature indicator solves this problem when attached to the package because it reaches its end point sooner when exposed to a higher temperature. In order to directly indicate the end of the shelf life, the time-temperature indicator characteristics should be matched as closely as possible to the quality characteristics of the product. When kept at the standard storage temperature for the product, the indicator should reach its end point at the same time as the product''s shelf life. In addition, to determine the accuracy of the match at other temperatures, the change of shelf life with temperature should be known for both the product and the indicator. The Arrhenius relationship is a common and convenient method of describing the change of shelf life with temperature. In cases where it is not applicable, individual time-temperature points for the product may be established and an approximate correlation with the TTI obtained. When attached to the package of a perishable product, a time-temperature indicator may supplement, or in some cases replace, the expiration date code. The addition of a TTI provides a greater level of confidence that the perishable product is within its shelf life because it responds to the actual temperature conditions to which the product has been exposed. In the case of minimally processed refrigerated foods, the rapid growth of pathogenic bacteria at elevated temperatures may pose a serious health hazard even before the deterioration of the quality of the product becomes apparent to the consumer. In this case, an expiration date may be used for storage at the standard temperature, while a threshold-temperature TTI is used to indicate the exposure to temperatures at which growth becomes measurable. It is also possible to use a dual-function TTI, in which case the standard TTI would indicate the shelf life at the correct storage temperature while the threshold-temperature part would indicate the exposure to higher temperatures.1.1 This guide covers information on the selection of commercially available time-temperature indicators (TTIs) for noninvasive external package use on perishable products, such as food and pharmaceuticals. When attached to the package of a perishable product, TTIs are used to measure the combined time and temperature history of the product in order to predict the remaining shelf life of the product or to signal the end of its usable shelf life. It is the responsibility of the processor of the perishable product to determine the shelf life of a product at the appropriate temperatures and to consult with the indicator manufacturer to select the available indicator which most closely matches the quality of the product as a function of time and temperature. Note 18212;Besides time-temperature indicator, TTI is also an abbreviation for time-temperature monitor and time-temperature integrator. 1.2 Time-temperature indicators may be integrated into a Hazard Analysis and Critical Control Point (HACCP) plan. Appropriate instructions should be established for handling products for which either the indicator has signaled the end of usable shelf life or the shelf life of the product at its normal storage temperature has been reached. 1.3 This standard does not purport to address all of the safety concerns,......

Standard Guide for Selection of Time-Temperature Indicators

GOST R 50856-1996 车速雷达仪.基本技术要求.测试方法

Настоящий стандарт устанавливает общие технические требования к радиолокационным измерителям скорости движения транспортных средств (д

Rodar meters of the speed of vehicles. Basic technical requirements. Methods of tests

JB/T 7814-1995 频率信号输出型转速传感器性能评定方法

本标准规定了频率信号输出型转速传感器性能评定用的试验方法和评定报告的内容。 本标准适用于以频率信号输出的用于在一般工作条件下使用的测量转速的转速传感器。 本标准所规定的某些试验可能不适用于某些型式的传感器，而某些型式的传感器可能需要其它的附加试验。可根据传感器的型式选择所适用的试验和补充所需的附加试验。

Performance evaluation method for frequency signal output revolution speed transducer

STAS SR ISO 3159:1994 计时仪器．腕计时器与弹簧平衡振荡器

Prezentul Standard Interna?ional stabile?te defini?ia termenului ?cronometru" descriind categoriile, programul ?ncerc?rilor ?i condi?iile minime admise pentru cronometrele br??ar?. NOT? — Ceasurile br??ar? echipate cu un oscilator cu diapazon sunt supuse acelora?i tncerc?ri at?t timp c?t nu exist? standarde specifice..

Timekeeping instruments. Wrist-chronometers with spring balance oscillator

STAS SR ISO 3157:1994 时间测量的辐射发光仪器．说明书

Radioluminescence for time measurement instruments - Specifications

CNS 2736-1994 汽车滑行试验法

本标准规定汽车之滑行试验方法。备考：本标准｛｝内之单位及数值，系国际单位制（SI）。

Method of Coastdown Test for Automobiles

AIR FORCE MS27573 REV A VALID NOTICE 2-1994 航空器凸缘架集油槽2 3/4英寸刻度盘仪器药筒

MS27573, dated 19 November 1968, has been reviewed and determined to be valid for use in acquisition.

CASE, INSTRUMENT, 2 3/4 INCH DIAL, WITH SUMP, FLANGE MOUNTED, AIRCRAFT