17.100 力、重力和压力的测量 标准查询与下载

ANSI/ASTM F2569:2011 体育运动用表面压力还原性能评估的试验方法

Test Method For Evaluating The Force Reduction Properties Of Surfaces For Athletic Use

GSO OIML R97:2010 大气压力测量装置

This standard specifies the metrological and technical requirements applicable to instruments for the measurement of ambient atmospheric pressure, and to the pattern evaluation. It has relevance to the following types: a) Mercury barometers having a permanent reference vacuum. b) Barometers, for example aneroid barometers, with an elastic sensing element, a permanent reference vacuum and an indication, which may be either analogue, with a pointer and a dial, or digital.

Barometers

UL 404-2010 压缩气体设备用气压计量表

UL Standard for Safety Gauges, Indicating Pressure, for Compressed Gas Service (Eighth Edition; Reprint with revisions through and including February 11, 2015)

GSO BS 7882:2010 如何校准和分类扭矩测量装置

This British Standard specifies requirements for the calibration and classification of torque measuring devices, including those used for the calibration of hand torque tools to BS EN ISO 6789. It describes the method of calibration, calculation of calibration results and the classification of the torque measuring device in a static mode. The information to be given on the certificate of calibration is also listed.

Method for calibration and classfication of torque measuring devices

SANS 1062:2010 压力和真空计

Covers circular analogue pressure gauges, vacuum gauges, and combined vacuum and pressure gauges (compound gauges) of nominal diameter in the range 40mm - 300mm and that operate in the range 100 kPa below atmospheric pressure to 250 MPa above atmospheric

Pressure and vacuum gauges

JB/T 9484-2010 深波波纹管尺寸系列

本标准规定了金属环形单层无缝深波波纹管(以下简称深波波纹管)的范围、型号标记、常用材料及尺寸基本参数。 本标准适用于仪器仪表中作为敏感元件的深波波纹管，其外径与内径之比值C(C=D/d)为1．6～2(即1.6≤D/d≤2)。

Series of dimension for deep bellows

DB36/T 574-2010 自反力平衡荷载箱

规定了自反力平衡荷载箱的要求、试验方法、检验规则及标志、运输和贮存

Reflexive Balance Load Box

GOST R 8.726-2010 国家测量一致性保证体系.传感器.计量和技术要求.试验

State system for ensuring the uniformity of measurements. Load cells. Metrological and technical requirements. Tests

ANSI/UL 404-2010 压缩气体装置用压力指示计的安全性标准

Proposal to revise the scope of the standard to include the addition of higher pressure gauge ranges

Standard for Safety for Gauges, Indicating Pressure, for Compressed Gas Service

ASME PTC 19.2-2010 压力测量

The methods for pressure measurement and the protocols used for data transmission are provided in this Supplement. Guidance is given for setting up the instrumentation and determining the uncertainty of the measurement. Information regarding the instrument type, design, applicable pressure range, accuracy, output, and relative cost is provided. Information on pressure-measuring devices that are not normally used in field environments is given in the Nonmandatory Appendices A (Piston Gauges), B (Manometers), and C [Low-Absolute-Pressure (Vacuum) Instruments].

Pressure Measurement (PTC 19.2 - 2010)

ANSI/ASME PTC19.2-2010 压力测试

Pressure Measurement

KS B 5520-2009(2019) 隔膜密封压力表

Diaphragm seal pressure gauges

KS B 5520-2009 隔膜压力表

이 표준은 지시계 내부의 봉입액과 피측정 유체를 분리하는 격막을 가진 압력계(이하, “격막

Diaphragm seal pressure gauges

KS R 2025-2009(2019) 汽车轮胎压力表

Tyre pressure gauges for automobiles

GSO EN 472:2009 压力表 词汇

This European standard defines the fundamental and general terms to be used for pressure gauges.

Pressure gauges – Vocabulary

GSO EN 12645:2009 压力表 检查车辆轮胎压力和/或充气的装置 计量要求和测试

This European standard defines requirements of pressure gauges for inflation of tyre and their testing in accordance with 86/217/EEC Directive. It establishes in the context of motor vehicles tyres, the minimum characteristics of the chain of measurement of mechanical apparatus intended to increase, inspect or adjust the pressure of tyres inflated by air or nitrogen. This apparatus classified in four different categories are hereinafter referred to by generic term, "pressure gauges". This chain of measurement consists of all the elements between the tyre valve and the display device (connector, hose, control device, measurement components, etc.). They indicate the pressure difference (Pe) between the air or the nitrogen in the tyre and the atmosphere. The field of application established above can be extended to other applications where no specific standard exists.

Pressure gauges-Apparatus for inspection of pressure and/ or inflation of tyres for motor vehicles-metrology, requirements and testing

BS 7996:2009 扭矩测量装置.使用连续扭矩应用的校准和分类.方法

This British Standard specifies a method for the calibration and classification of torque measuring devices using continuous torque application where the inertial effects are minimal. This includes torque measuring devices used for the calibration of hand torque tools conforming to BS EN ISO 6789, and torque measuring devices conforming to BS 7882. The information to be given on the certificate of calibration is also specified in this standard. Annex A provides diagrams of the continuous application of torque, and examples for the calibration of torque measuring devices. Annex B gives an example of determining uncertainty of the calibration results of the torque measuring device. Annex C shows how to calculate mechanical and electronic bandwidth.

Torque measuring devices - Calibration and classification using continual torque application - Method

JIS B 7602:2009 测力仪用校准和试验方法

This Japanese Industrial Standard was established in 1983 and to this day has gone through two revisions.

Calibration and test method for force-proving instruments

JIS B 7611-2:2009 非自动称量仪器.度量衡学和技术要求及试验.第2部分:记录或鉴定用测量仪器

Non-automatic weighing instruments -- Metrological and technical requirements and tests -- Part 2: Measuring instruments used in transaction or certification

GSO OIML D23:2009 检定设备计量控制原理

This Document deals with "verification equipment" i.e. equipment used for the verification of measuring instruments in the field of legal metrology. The technical equipment considered to be verification equipment may vary greatly in complexity, size, manner of installation, transportability, etc., hence the use of particular terms such as verification apparatus, verification station, verification installation, automated verification equipment, etc.

Principles for metrological control of equipment used for verification