17.100 力、重力和压力的测量 标准查询与下载

KS R 2025-2019 汽车轮胎压力表

Tyre pressure gauges for automobiles

BS 7996:2018 扭矩测量装置 使用连续扭矩应用进行校准和分类 方法

What is BS 7996- Torque measuring devices about?   BS 7996 is a safety standard on torque measuring devices .   BS 7996 specifies a method for the calibration and classification of torque measuring devices using continuous torque application where the inertial effects are minimal. BS 7996 includes torque measuring devices used for the calibration of torque tools.   BS 7996 provides diagrams of the continuous application of torque and examples for the calibration of torque measuring devices. BS 7996 also gives an example of determining the uncertainty of the calibration results of the torque measuring device. BS 7996 shows how to calculate mechanical and electronic bandwidth.   Who is BS 7996-

Torque measuring devices. Calibration and classification using continual torque application. Method

KS B 5305-2018(2023) 波登管压力表

Bourdon tube pressure gauges

KS B 5305-2018 波登管压力表

Bourdon tube pressure gauges

T/SJZJLXH 0002-2018 现场压力检测系统校准规范

本规范规定了术语及定义、功能概述、计量性能要求、现场压力测量系统技术要求、计量器具控制

Calibration specification for on-site pressure detection system

T/JHY 01-2018 压力变送器

1、变送器准确度等级的规定； 2、差压变送器额定工作压力对量程范围要求； 3、与准确度等级有关的要求。

pressure transmitter

DIN 8119-6:2018 台秤.第6部分:铁路称量台和铁路及道路结合称量台的设计载荷

This standard describes the calculation of rail weighbridges and combined rail/road weighbridges using load assumptions. For compiling the analysis of structural safety and for detailed consruction of supporting parts, please use "DIN-Fachbericht 101". According to the latter, the calculation of supporting structures in tracks with standard track width does not use the real loads but rather load model UIC 71 (Union Internationale des Chemins de fer - International Railway Organization) see "DIN-Fachberichtes 101, figure 6.2."

Platform scales - Part 6: Design loads for rail weighbridges and combined rail and road weighbridges

T/ZZB 0362-2018 耐震精密压力表

本标准规定了耐震精密压力表的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装与贮存及质量承诺等要求。 本标准适用于测量元件为弹簧管（C形管、螺旋管），并采用灌充液和阻尼器进行防震处理的机械指针式精密压力表和精密真空表（以下简称仪表）。

Shock-resistant accurate pressure gauge

T/CSEB 0003-2018 岩石材料冲剪试样动态剪切强度测试方法

本标准规定了岩石材料冲剪试样动态剪切强度测试的方法。 本标准适用于常温常压条件下测定岩石材料的动态剪切强度参数。

Testing method for determining dynamic shear strength of rock materials by the punch shear specimen

T/CSEB 0002-2018 岩石材料半圆盘弯曲试样动态弯曲强度测试方法

本标准规定了岩石材料半圆盘弯曲试样动态弯曲强度测试的方法。 本标准适用于常温常压条件下测定岩石材料的动态弯曲拉伸强度参数。

Testing method for determining dynamic bending strength of rock materials by the Semi-circular Bending specimen

T/CSEB 0004-2018 岩石材料动态单轴压缩强度测试方法

本标准规定了岩石材料动态单轴压缩强度测试的方法。 本标准适用于常温常压条件下测定岩石材料的动态单轴压缩强度参数。

Testing method for determining the dynamic unaxial compression strength of rock materials

T/CSEB 0006-2018 岩石材料直切槽半圆盘弯曲试样动态起裂韧度测试方法

本标准规定了岩石材料直切槽半圆盘弯曲试样动态起裂韧度测试的方法。 本标准适用于常温常压条件下测定中粗晶粒岩石材料的I型动态起裂韧度。

Testing method for determining dynamic fracture toughness of rock materials by the Notched Semi-circular Bending specimen

T/CSEB 0005-2018 岩石材料人字型切槽半圆盘弯曲试样动态起裂韧度测试方法

本标准规定了岩石材料人字型切槽半圆盘弯曲试样动态起裂韧度测试的方法。 本标准适用于常温常压条件下测定细晶粒岩石材料的动态I型起裂韧度。

Testing method for determining dynamic fracture toughness of rock materials by the Chevron Notched Semi-circular Bending specimen

T/CSEB 0001-2018 岩石材料巴西圆盘试样动态拉伸强度测试方法

本标准规定了岩石材料巴西圆盘试样动态拉伸强度测试的方法。 本标准适用于常温常压条件下测定岩石材料的动态拉伸强度参数。

Testing method for determining dynamic tensile strength of rock materials by the Brazilian disc specimen

ASTM F721-18 标准管道组件的标准规范

Standard Specification for Gage Piping Assemblies

ASTM E1719-12(2018) 用沸点计法测定液体蒸气压的标准试验方法

1.1 This test method describes procedures for determination of the vapor pressure of liquids by ebulliometry (boiling point measurements). It is applicable to pure liquids and azeotropes that have an atmospheric boiling point between 285 and 575 K and that can be condensed completely and returned to the ebulliometer boiler, that is, all materials must be condensable at total reflux. Liquid mixtures may be studied if they do not contain non-condensable components. Liquid mixtures that contain trace amounts of volatile but completely condensable components may also be studied, but they will produce vapor pressure data of greater uncertainty. Boiling point temperatures are measured at applied pressures of 1.0 to 100 kPa (7.5 to 760 torr). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 There is no ISO equivalent to this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Vapor Pressure of Liquids by Ebulliometry

T/ZZB 0340-2018 Ⅲ级电子吊秤

本标准规定了 级的电子吊秤（以下简称“吊秤”）的术语和定义、型号及规格的命名、基本要求、计量要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于对处于自由悬吊状态下的被称物品进行称量且准确度等级为 级的无线数传式、秤体直视式电子吊秤。

Medium accuracy electronic crane and hanging scale

ASTM E74-18 测力仪器校准和验证的标准实施规程

Standard Practices for Calibration and Verification for Force-Measuring Instruments

ASTM E74-18e1 测力仪器校准和验证的标准实施规程

1.1 The purpose of these practices is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform scales. NOTE 1—Verification by deadweight loading is also an acceptable method of verifying the force indication of a testing machine. Tolerances for weights for this purpose are given in Practices E4; methods for calibration of the weights are given in NIST Technical Note 577(1)2 , Methods of Calibrating Weights for Piston Gages. 1.2 The values stated in SI units are to be regarded as the standard. Other metric and inch-pound values are regarded as equivalent when required. 1.3 These practices are intended for the calibration of static force-measuring instruments. It is not applicable for dynamic or high speed force calibrations, nor can the results of calibrations performed in accordance with these practices be assumed valid for dynamic or high speed force measurements. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practices for Calibration and Verification for Force-Measuring Instruments

DIN 16003:2018 机械压力表和温度表. 差压表. 尺寸计量要求和试验

This standard specifies requirements for differential pressure gauges.

Mechanical pressure and temperature gauges - Differential pressure gauges - Dimensions, metrology, requirements and testing