19.080 电工和电子试验 标准查询与下载

IEC 61010-2-032:2012 测量、控制和试验室用电气设备的安全性要求.第2-032部分:电气测量和试验用手持和用手控制电流感应器的详细要求

Scope and object This clause of Part 1 is applicable except as follows: Equipment included in scope Replacement: Replace the existing text with the following: This part of IEC 61010 specifies safety requirements for HAND-HELD and hand-manipulated current sensors described below. These current sensors are for measuring@ detecting or injecting current@ or indicating current waveforms on circuits without physically opening the current path of the circuit being measured. They may be stand-alone current sensors or accessories to other equipment or parts of combined equipment (see Figure 101). These include measurement circuits which are part of electrical test and measurement equipment@ laboratory equipment@ or process control equipment. The existence of these current sensors and circuits in equipment requires additional protective means between the current sensor@ the circuit and an OPERATOR. NOTE 1 This part includes also the requirements of Part 2-030. Testing and measuring circuits that are not within the scope of this part are considered to be covered by the requirements of Part 1 or other parts 2s of IEC 61010@ and then will also need to meet the requirements of these other parts with the exception of Part 2-030. Current clamp meters and similar currents sensors that have a primary purpose of measuring voltage on a live MAINS CIRCUIT are also within the scope of Part 2-033. NOTE 2 Some current sensors are also known as current clamps and current probes. Current sensors require hand manipulation before or after a test or measurement@ but do not necessarily need to be HAND-HELD during the test or measurement. NOTE 3 Some current sensors designed for portable use can also be used for fixed installations. The following types of current sensors are covered: a) Type A: a current sensor designed to be applied around or removed from UNINSULATED HAZARDOUS LIVE conductors. Type A current sensors have defined HAND-HELD or handmanipulated parts providing protection against electric shock from the conductor being measured@ and also have protection against short-circuits between wires and busbars during clamping. b) Type B: a current sensor which has protection against short-circuits between wires or busbars during clamping but without defined HAND-HELD or hand-manipulated parts which provide protection against electric shock during clamping. Additional protective means are necessary to avoid electric shock from HAZARDOUS LIVE conductors which cannot be deenergised during application or removal of the current sensor. EXAMPLE 1 Flexible current sensors. c) Type C: a current sensor without protection against short-circuits between wires or busbars during clamping. Type C current sensors are intended to be applied to or removed from UNINSULATED HAZARDOUS LIVE conductors or from non-limited-energy circuit conductors only when they are de-energised. EXAMPLE 2 Split-core transducers. d) Type D: a current sensor designed to be applied around or removed from insulated conductors or from limited-energy circuit conductors. A Type D current sensor does not need protection against short-circuits during clamping and has no defined HAND-HELD or hand-manipulated parts providing protection against electric shock from the conductor being measured. EXAMPLE 3 Current probes for oscilloscopes and earth leakage current detectors. NOTE 4 All current sensors can also be used around insulated conductors. In this case@ HAZARDS are limited to acceptable levels by the insulation of the conductors.

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement

EN 61010-2-091:2012 测量、控制和实验室用电气设备的安全要求 第 2-091 部分：柜式 X 射线系统的特殊要求

IEC 61010-2-091:2012 specifies particular safety requirements for CABINET X-RAY SYSTEMS. A CABINET X-RAY SYSTEM is a system that contains an X-ray tube installed in a cabinet which, independently of existing architectural structures except the floor on which it may be placed, is intended to contain at least that portion of a material being irradiated, provide radiation attenuation, and exclude personnel from the interior during generation of X-radiation. These CABINET X-RAY SYSTEMS are used in industrial, commercial, and public environments, for example, to inspect materials, to analyze materials, and to screen baggage.

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-091: Particular requirements for cabinet X-ray systems

CAN/CSA-C393-2012(R2017) 测量商业和工业设备低功耗和闲置功耗模式下功耗的测试方法

Scope 1.1 This Standard specifies methods for measuring electrical power consumption of equipment intended for use in commercial and industrial application when in low power mode(s) (i.e., standby mode, off mode, and network mode) and idle mode. This Standard is applicable to electrical products with a rated input voltage or voltage range that lies wholly or partly in the range 100 V a.c. to 347 V a.c. for single phase input and 130 V a.c. to 7200 V a.c. for other inputs. Notes: (1) The measurement of energy consumption and performance of products during intended use are generally specified in the relevant product standards and are not covered by this Standard. (2) Where this Standard is referenced by performance standards or procedures, these should define and name the relevant low power modes (see Clause 3) to which this Standard is applied. (3) The inclusion of d.c. powered products within the scope of this Standard is under consideration. 1.2 This Standard does not specify safety requirements. It does not specify minimum performance requirements nor does it set maximum limits on power or energy consumption. The methods described in this Standard are not intended to be used to measure power consumption of products during in-service mode, as these are generally covered by other product standards (see Bibliography for some examples), although the measuring techniques, measurement uncertainty determination, and test equipment specifications may be adapted for such measurements with careful review. 1.3 In CSA standards, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.

Test methods for measuring power consumption in low and idle power modes of commercial and industrial equipment

CAN/CSA-C393-2012(C2017) 测量商业和工业设备在空闲和低功耗模式下的功耗的方法

1.1 Cette norme stipule des méthodes de mesure de la consommation électrique dans des modes faible puissance (c.-à-d., mode veille, mode arrêt et mode réseau) et le mode repos d’équipements destinés à des applications industrielles et commerciales. Cette norme s’applique aux produits électriques dont la plage de tension ou la tension d’entrée nominale est comprise totalement ou en partie entre 100 V c.a. à 347 V c.a. pour l’entrée monophasée et 130 V c.a. à 7200 V c.a. pour les autres entrées. Notes : 1) La mesure de la consommation d’énergie et le rendement des produits durant l’utilisation prévue sont généralement précisées dans les normes pertinentes sur les produits et ne sont pas traitées dans cette norme. 2) Lorsque cette norme est citée dans des procédures ou des normes fonctionnelles, celles-ci devraient définir et nommer les modes faible puissance concernés (voir le chapitre 3) auxquels elle s’applique. 3) L’inclusion dans le domaine d’application de cette norme de produits alimentés en courant continu est à l’étude. 1.2 Cette norme ne spécifie pas des exigences de sécurité. Elle ne précise aucune exigence minimale de rendement ni ne définit aucune limite maximale de consommation d’énergie ou de puissance. Les méthodes décrites dans cette norme n’ont pas pour but la mesure de la consommation de produits en mode service, car cette question est généralement traitée dans d’autres normes (voir la bibliographie pour quelques exemples), bien que les techniques de mesure, la détermination des incertitudes de mesure et les spécifications des équipements d’essai puissent être adaptées pour de telles mesures, à la suite d’une révision attentive. 1.3 Dans cette norme, le terme «doit» indique une exigence, c’est-à-dire une prescription que l’utilisateur doit respecter pour assurer la conformité à la norme ; «devrait» indique une recommandation ou ce qu’il est conseillé mais non obligatoire de faire ; et «peut» indique une possibilité ou ce qu’il est permis de faire. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes sont qualifiées de normatives (obligatoires) ou d’informatives (facultatives) pour en préciser l’application.

Methods for measuring the consumption of commercial and industrial equipment in idle and low power modes

GOST R 55193-2012 电压为3 kV及以上的电气设备及装置. 高压试验期间的测量方法

Electric equipment and installations for 3 kV and higher. Measuring methodsduring high - voltage tests

IEC 60060:2024 SER 高压测试技术-所有零件

High-voltage test techniques - ALL PARTS

GSO IEC 61010-1:2011 测量、控制和实验室用电气设备的安全要求 第1部分：一般要求

IEC 61010-1:2010 specifies general safety requirements for the following types of electrical equipment and their accessories, wherever they are intended to be used. a) Electrical test and measurement equipment b) Electrical industrial process-control equipment c) Electrical laboratory equipment This third edition cancels and replaces the second edition published in 2001. It constitutes a technical revision. This edition includes the following significant changes from the second edition, as well as numerous other changes. - The scope of the standard has been expanded to include all locations where these products may be used, so that both professional and non-professional versions of these products are within the scope. - The requirements for testing and measuring circuits (in various subclauses and the entirety of Clause 16) have been removed and included in a particular standard IEC 61010-2-030. - Insulation requirements (6.7) have been completely rewritten. - Additional requirements for protection against mechanical HAZARDS (Clause 7) have been included. - Surface temperature limits (Clause 10) have been modified to conform to the limits of EN 563. - Radiation requirements (Clause 12) have been modified, and take into account a distinction between intended emission and unintended emission. - Requirements for reasonably foreseeable misuse and ergonomic aspects have been added (Clause 16).

Safety Requirements for Electrical Equipment for Measurement, control, and laboratory use – Part 1: General Requirements

DIN EN 60060-2:2011 高压试验技术.第2部分:测量系统(IEC 60060-2-2010);德文版本EN 60060-2-2011

High-voltage test techniques - Part 2: Measuring systems (IEC 60060-2:2010); German version EN 60060-2:2011

DIN EN 60060-1:2011 高压试验技术.第1部分:通用定义和试验要求(IEC 60060-1-2010);德文版本EN 60060-1-2010

High-voltage test techniques - Part 1: General definitions and test requirements (IEC 60060-1:2010); German version EN 60060-1:2010

LST EN 62475-2011 大电流测试技术 测试电流和测量系统的定义和要求（IEC 62475:2010）

High-current test techniques - Definitions and requirements for test currents and measuring systems (IEC 62475:2010)

BS EN 60060-2:2011 高压试验技术.测量系统

High-voltage test techniques. Measuring systems

DS/EN 62475:2011 大电流测试技术 测试电流和测量系统的定义和要求

IEC 62475:2010 is applicable to high-current testing and measurements on both high-voltage and low-voltage equipment. It deals with steady-state and short-time direct current (as e.g. encountered in high-power d.c. testing), steady-state and short-time alternating current (as e.g. encountered in high-power a.c. testing), and impulse-current. In general, currents above 100 A are considered in this International Standard, although currents less than this can occur in tests. This standard also covers fault detection during, for example, lightning impulse testing.

High-current test techniques - Definitions and requirements for test currents and measuring systems

JIS C 1010-31:2011 测量,控制和实验室用电气设备的安全性要求.第31部分:电气测量和试验用手持探测器装置安全性要求

Safety requirements for electrical equipment for measurement, control and laboratory use -- Part 31: Safety requirements for hand-held probe assemblies for electrical measurement and test

DS/EN 60060-1:2011 高压测试技术 第1部分：一般定义和测试要求

IEC 60060-1:2010 applies to dielectric tests with alternating voltage; dielectric tests with direct voltage; dielectric tests with impulse voltage and dielectric tests with combinations of the above. This document is applicable to tests on equipment having its highest voltage for equipment Um above 1 kV. The third edition cancels and replaces the second edition, published in 1989, and constitutes a technical revision. The major technical changes with respect to the previous edition are as follows: - artifical pollution test procedures were removed as they are now described in IEC 60507, - measurement of impulse current has been transferred to a new standard

High-voltage test techniques – Part 1: General definitions and test requirements

DS/EN 60060-2:2011 高压测试技术 第2部分：测量系统

IEC 60060-2:2010 is applicable to complete measuring systems, and to their components, used for the measurement of high voltages during laboratory and factory tests with direct voltage, alternating voltage and lightning and switching impulse voltages as specified in IEC 60060-1. For measurements during on-site tests see IEC 60060-3. The limits on uncertainties of measurements stated in this standard apply to test levels stated in IEC 60071-1:2006. The principles of this standard apply also to higher levels but the uncertainty may be greater. This standard also defines the terms used, methods to estimate the uncertainties of high-voltage measurements, states

High-voltage test techniques - Part 2: Measuring systems

BS EN 60060-1:2011 高压试验技术 一般定义和试验要求

High-voltage test techniques. General definitions and test requirements

BS EN 60060-1:2010 高压试验技术.一般定义和试验要求

High-voltage test techniques. General definitions and test requirements

DS/EN 61010-2-030:2011 测量、控制和实验室用电气设备的安全要求 第 2-030 部分：测试和测量电路的特殊要求

IEC 61010-2-030:2010 specifies safety requirements for testing and measuring circuits which are connected for test or measurement purposes to devices or circuits outside the measurement equipment itself. These include measurement circuits which are part of electrical test and measurement equipment, laboratory equipment, or process control equipment. The existence of these circuits in equipment requires additional protective means between the circuit and an OPERATOR. This Part 2-030 is to be used in conjunction with the latest edition of IEC 61010-1. It was established on the basis of the third edition (2010) of IEC 61010-1. Consideration may be given to fut

Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for testing and measuring circuits

DS/EN 50191:2011 电气测试设备的安装和操作

1.1 This European Standard is applicable to the erection and operation of fixed and temporary electrical test installations.1.2 Compliance with this European Standard is not necessary, if contact with live parts presents no danger. This is the case when one of the following conditions is satisfied at live exposed points:a) the voltage at frequencies above 500 Hz does not exceed 25 V a.c. or 60 V d.c. and complies with the requirements for SELV or for PELV in accordance with HD 60364-4-41;b) in case of voltages at frequencies up to 500 Hz exceeding 25 V a.c. or 60 V d.c., the resultant current through a non-inductive resi¬stance of 2 k¿ does not exceed 3 mA

Erection and operation of electrical test equipment

GOST IEC 61010-2-032-2011 测量、控制和实验室用电气设备的安全性要求.第2-032部分:电气测量和试验用手持式电流夹钳的详细要求

Safety requirements for electrical equipment for measurement, control and laboratory use. Part 2-032. Particular requirements for hand-held current clamps for electrical measurement and test