19.080 电工和电子试验 标准查询与下载

CAN/CSA-C22.2 No.61010-031-2017 电气测量、调节和实验室设备的安全要求 第031部分：电气测量和测试用手持式探头的安全要求

1.1.1 Sondes équipées incluses dans le domaine d'application La présente partie de l'IEC 61010 spécifie les exigences de sécurité relatives aux sondes portatives et manipulées à la main correspondant aux types décrits ci-dessous, ainsi que leurs accessoires connexes. Ces sondes équipées sont prévues pour la connexion électrique directe entre une partie et un appareil de mesure et d'essai électrique. Elles peuvent être solidaires de l'appareil ou en être des accessoires détachables. a) Type A: sondes équipées, sans atténuation, à basse tension et à haute tension. Sondes équipées sans atténuation, ASSIGNEES pour connexion directe à des tensions supérieures à 30 V efficaces ou à 42,4 V crête ou à 60 V continus, mais ne dépassant pas 63 kV. Elles ne comportent pas de composants qui sont prévus pour assurer une fonction de diviseur de tension ou une fonction de mise en forme de signaux, mais elles peuvent contenir des composants ne provoquant pas d’atténuation tels que des fusibles (voir la Figure 1). b) Type B: sondes équipées à atténuateur ou diviseur à haute tension. Sondes équipées à atténuateur ou diviseur ASSIGNEES pour connexion directe sur des tensions secondaires supérieures à 1 kV efficaces ou 1,5 kV continus mais n'excédant pas 63 kV efficaces ou continus. La fonction de diviseur peut être réalisée dans sa totalité à l’intérieur de la sonde équipée, ou en partie dans l’appareil de mesure ou d’essai destiné à être utilisé avec la sonde équipée (voir la Figure 2). c) Type C: sondes équipées à atténuateur ou diviseur à basse tension. Sondes équipées à atténuateur ou diviseur pour connexion directe sur des tensions ne dépassant pas 1 kV efficaces ou 1,5 kV continus. La fonction de mise en forme de signaux peut être réalisée dans sa totalité à l’intérieur de la sonde équipée, ou en partie dans l’appareil de mesure ou d’essai destiné à être utilisé avec la sonde équipée (voir la Figure 3). d) Type D: sondes équipées à basse tension à atténuateurs, sans atténuation ou autres sondes de mise en forme de signaux qui ont des CARACTERISTIQUES ASSIGNEES pour connexion directe uniquement à des tensions n'excédant pas 30 V efficaces ou 42,4 V crête ou 60 V continus, et qui sont adaptées pour des courants dépassant 8 A (voir la Figure 4). 1.1.2 Sondes équipées exclues du domaine d'application La présente norme ne s'applique pas aux capteurs de courant relevant du domaine d'application de l'IEC 61010-2-032 (capteurs de courant portatifs et manipulés à la main), mais peut s'appliquer à leurs cordons d'entrée de circuit de mesure et à leurs accessoires.

Safety requirements for electrical measuring, regulating and laboratory apparatus — Part 031: Safety requirements for equipped hand-held probes for electrical measurement and testing

DIN EN 61010-031/A1:2017 测量、控制和实验室用电气设备的安全要求. 第031部分：电气试验和测量用手持式和手持式探头组件的安全要求(IEC 23J/432/CDV:2017)；德文版本EN 61010-031:2015/prA1:2017

This part of IEC 61010 specifies safety requirements for hand-held and hand-manipulated probe assemblies of the types described below, and related accessories. These probe assemblies are for use in the interface between an electrical phenomenon and electrical test and measurement equipment. They may be fixed to the equipment or be detachable accessories for the equipment.

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and measurement (IEC 66/632/CDV:2017); German version EN 61010

BS EN 61010-2-012:2016 测量, 控制和实验室使用电气设备的安全要求. 气候和环境试验设备及其他温度调节设备的详细要求

Safety requirements for electrical equipment for measurement, control and laboratory use. Particular requirements for climatic and environmental testing and other temperature conditioning equipment

BS EN 61180:2016 低压设备的高压试验技术.定义、试验和方法要求、试验设备

High-voltage test techniques for low-voltage equipment. Definitions, test and procedure requirements, test equipment

DB23/T 1802-2016 可燃气体和有毒气体报警系统检测技术规范

Technical specification for detection of combustible gas and toxic gas alarm system

EN 61010-2-012:2016 测量控制和实验室用电气设备的安全要求 第 2-012 部分：气候和环境测试及其他温度调节设备的特殊要求

Safety requirements for electrical equipment for measurement@ control and laboratory use - Part 2-012: Particular requirements for climatic and environmental testing and other temperature conditioning equipment

EN 61180:2016 低压设备的高压测试技术 定义、测试和程序要求、测试设备

IEC 61180:2016 is applicable to dielectric tests with direct voltage; dielectric tests with alternating voltage; dielectric tests with impulse voltage and test equipment used for dielectric tests on low-voltage equipment. This standard is applicable only to tests on equipment having a rated voltage of not more than 1 kV a.c. or 1,5 kV d.c. This standard is applicable to type and routine tests for objects which are subjected to high voltage tests as specified by the technical committee. The test equipment comprises a voltage generator and a measuring system. This standard covers test equipment in which the measuring system is protected against external interference and coupling by appropriate screening, for example a continuous conducting shield. Therefore, simple comparison tests are sufficient to ensure valid results. This standard is not intended to be used for electromagnetic compatibility tests on electric or electronic equipment. Tests with the combination of impulse voltages and currents are covered by IEC 61000-4-5. This standard provides the relevant technical committees as far as possible with: - defined terms of both general and specific applicability; - general requirements regarding test objects and test procedures; - methods for generation and measurement of test voltages; - test procedures; - methods for the evaluation of test results and to indicate criteria for acceptance; - requirements concerning approved measuring devices and checking methods and measurement uncertainty. Alternative test procedures may be required and these should be specified by the relevant technical committees. Care should be taken if the test object has voltage limiting devices, as they may influence the results of the test. The relevant technical committees should provide guidance for testing objects equipped with voltage limiting devices. This 1st edition of IEC 61180 cancels and replaces the 1st edition of IEC 61180-1, issued in 1992, and the 1st edition of IEC 61180-2, issued in 1994. Key words: High Voltage Test Techniques, Dielectric Tests, Disruptive Discharge, Withstand Voltage.

High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment

IEC 61010-2-012:2016 测量 控制和实验室用电气设备的安全要求 - 第2-012部分:气候和环境试验及其他温度调节设备的特殊要求

Equipment included in scope This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope@ but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard@ in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51. This Part 2 of IEC 61010 specifies safety requirements for electrical equipment and their accessories within the categories a) through c)@ wherever they are intended to be used@ whenever that equipment incorporates one or more of the following characteristics: ?C A REFRIGERATING SYSTEM that is acted on or impacted by an integral heating function such that the combined heating and cooling system generates additional and/or more severe HAZARDS than those for the two systems if treated separately. ?C The materials being treated in the intended application introduce significant heat into the REFRIGERATING SYSTEM that the cooling system in the application yield additional and/or more severe HAZARDS than those for the cooling system if operated at the maximum RATED ambient alone. ?C An irradiation function for the materials being treated presenting additional HAZARDS. ?C A function to expose the materials being treated to excessive humidity@ carbon dioxide@ salt mist@ or other substances which may result in additional HAZARDS. ?C A function of MECHANICAL MOVEMENT presenting additional HAZARDS. ?C Provision for an OPERATOR to walk-in to the operating area to load or unload the materials being treated If all or part of the equipment falls within the scope of one or more other Part 2 standards of IEC 61010 as well as within the scope of this standard@ it should also meet the requirements of those other Part 2 standards. However@ when the equipment incorporates only a REFRIGERATING SYSTEM or only a heating function or a combination of the two without introducing additional HAZARDS described in the above dashed paragraphs then the application of IEC 61010-2-011 or IEC 61010-2-010 or both@ as applicable@ shall be considered instead of this Part 2. See further information in the flow chart for selection process and guidance in the INTRODUCTION. NOTE 102 Subclause 3.1.107 and Annex BB provides definition and requirements for protection of people who are inside WALK-IN EQUIPMENT.

Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-012: Particular requirements for climatic and environmental testing and other temperature conditionin

DIN EN 61010-031:2016 测量、控制和实验室用电气设备的安全要求.第031部分:电气测量和试验用手持探头组件的安全要求(IEC 61010-031-2015).德文版本EN 61010-031-2015

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test (IEC 61010-031:2015); German version EN 61010-031:2015

IEC 61180:2016 低压设备的高压测试技术 - 定义 测试和程序要求 测试设备

High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment

DB44/T 1779-2015 纯电动汽车驱动系统能量传递效率测试方法

本标准规定了纯电动汽车驱动系统能量传递效率的测试方法。 本标准适用于M1类、N1类纯电动汽车。

Test method for energy transfer efficiency of pure electric vehicle drive system

DB44/T 1780-2015 电动汽车充电器效率试验方法

本标准规定了电动汽车充电器效率试验方法。 本标准适用于电动汽车充电器，其它电动车辆的充电器可参照执行。

Efficiency Test Method for Electric Vehicle Charger

LST EN 61010-031-2015 测量, 控制和实验室用电气设备的安全要求. 第031部分: 电工测量和试验用手持探头组件的安全要求(IEC 61010-031-2015)

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test (IEC 61010-031:2015)

GSO IEC/TR 62434:2015 困难介质中的 pH 测量 定义、规范和程序

This Technical Report concerns analyzers, sensor units and electronic units used for the determination of pH in non-aqueous solvents and aqueous organic solvent mixtures using glass electrodes. IEC 60746-1 includes further definition of the scope and provides for the general aspects of all electrochemical analyzers, including pH. It is worthwhile to remind that IEC 60746-2 contains specifications for simulators used for testing pH electronic units. This technical report specifies the terminology, definitions, methodology, requirements for statements by manufacturers and performance tests for analyzers, sensor units and electronic units used for the determination of pH value in non-aqueous and aqueous-organic solvent mixtures.

pH measurements in difficult media - Definitions, standards and procedures

GSO IEC 61010-2-020:2015 测量、控制和实验室用电气设备的安全要求 第2-020部分：实验室离心机的具体要求

Replacement: This Part 2 is applicable to electrically powered LABORATORY CENTRIFUGES. NOTE If all or part of the equipment falls within the scope of one or more other Part 2 standards of IEC 61010 as well as within the scope of this standard, it will also need to meet the requirements of those other Part 2 standards. 1.1.2 Equipment excluded from scope Addition: Add the following new item: aa) IEC 60034 (Rotating electrical machinery);

Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-020: Particular requirements for laboratory centrifuges

GSO IEC 61340-4-4:2015 静电 第4-4部分：特定应用的标准测试方法 柔性介质包装容器的静电分类

This part of IEC 61340 describes procedures for evaluating the ignition risk presented by electrostatic discharges from FIBC to flammable or explosive environments. The requirements of this standard are applicable to all types of FIBC, tested as manufactured, prior to usage, intended for use without liners in flammable or explosive environments with minimum ignition energy of more than 0,14 mJ, and where the charging currents do not exceed 3,0 μA. NOTE 0,14 mJ is the minimum ignition energy normally quoted for methanol. Although more sensitive materials exist, methanol has the lowest minimum ignition energy of any material that is likely to be present when FIBC are emptied. 3,0 μA is the highest charging current likely to be found in common industrial processes. This combination of minimum ignition energy and charging current represents the most severe conditions that might be expected in practice. Compliance with the requirements of this standard does not mitigate the need for full risk assessment. The test methods included in this standard may be used in association with other performance requirements, for example when a risk assessment has shown the minimum ignition energy of concern is less than 0,14 mJ or charging currents greater than 3,0 μA are present.

Electrostatics -- Part 4-4: Standard test methods for specific applications - Electrostatic classification of flexible intermediate bulk containers (FIBC)

EN 61010-031:2015 测量,控制和实验室用电气设备的安全要求.第031部分:电气测量和试验用手持式测试装置的安全要求

Safety requirements for electrical equipment for measurement@ control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test

IEC 61010-031:2015 测量、控制和实验室用电气设备的安全要求.第031部分:电气测量和试验用手持式探头组件的安全要求

Probe assemblies included in scope This part of IEC 61010 specifies safety requirements for hand-held and hand-manipulated probe assemblies of the types described below@ and their related accessories. These probe assemblies are for direct electrical connection between a part and electrical test and measurement equipment. They may be fixed to the equipment or be detachable accessories for the equipment. a) Type A: low-voltage and high-voltage@ non-attenuating probe assemblies. Non-attenuating probe assemblies that are RATED for direct connection to voltages exceeding 30 V r.m.s.@ 42@4 V peak@ or 60 V d.c.@ but not exceeding 63 kV. They do not incorporate components which are intended to provide a voltage divider function or a signal conditioning function@ but they may contain non-attenuating components such as fuses (see Figure 1.) b) Type B: high-voltage attenuating or divider probe assemblies. Attenuating or divider probe assemblies that are RATED for direct connection to secondary voltages exceeding 1 kV r.m.s. or 1@5 kV d.c. but not exceeding 63 kV r.m.s. or d.c. The divider function may be carried out wholly within the probe assembly@ or partly within the test or measurement equipment to be used with the probe assembly (see Figure 2). c) Type C: low-voltage attenuating or divider probe assemblies. Attenuating or divider probe assemblies for direct connection to voltages not exceeding 1 kV r.m.s. or 1@5 kV d.c. The signal conditioning function may be carried out wholly within the probe assembly@ or partly within the test or measurement equipment intended to be used with the probe assembly (see Figure 3). d) Type D: low-voltage attenuating@ non-attenuating or other signal conditioning probe assemblies@ that are RATED for direct connection only to voltages not exceeding 30 V r.m.s.@ or 42@4 V peak@ or 60 V d.c.@ and are suitable for currents exceeding 8 A (see Figure 4). Probe assemblies excluded from scope This standard does not apply to current sensors within the scope of IEC 61010-2-032 (Handheld and hand-manipulated current sensors)@ but may apply to their input measuring circuit leads and accessories. Object Aspects included in scope The purpose of the requirements of this standard is to ensure that HAZARDS to the OPERATOR and the surrounding area are reduced to a tolerable level. Requirements for protection against particular types of HAZARDS are given in Clauses 6 to 13@ as follows: a) electric shock or burn (see Clauses 6@ 10 and 11); b) mechanical HAZARDS (see Clauses 7@ 8 and 11); c) excessive temperature (see Clause 9); d) spread of fire from the probe assembly (see Clause 9); e) arc flash (see Clause 13). Additional requirements for probe assemblies which are designed to be powered from a lowvoltage mains supply@ or include other features not specifically addressed in this standard are in other parts of IEC 61010. NOTE Attention is drawn to the possible existence of additional requirements regarding the health and safety of labour forces. Aspects excluded from scope This standard does not cover: a) reliable function@ performance@ or other properties of the probe assembly; b) effectiveness of transport packaging.

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test

EN 61010-2-051:2015 测量,控制和实验室用电气设备的安全要求.第2-051部分:机械混合和搅拌用实验室设备的特殊要求

IEC 61010-2-051:2015 is applicable to electrically operated laboratory equipment and its accessories for mechanical mixing and stirring, where mechanical energy influences the shape or size or homogeneity of materials and their accessories. Such devices may contain heating elements. It has the status of a group safety publication in accordance with IEC Guide 104. This third edition cancels and replaces the second edition published in 2003. It constitutes a technical revision and includes the following change from the second edition: - exclusion of equipment, whose size and weight make unintentional movement unlikely, from the drop test in Clause 8, - added requirement for interlock systems containing electric/electronic or programmable components to Clause 15, - notes have been re-phrased according to ISO/IEC Directives.

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-051: Particular requirements for laboratory equipment for mixing and stirring

EN 61010-2-061:2015 测量,控制和实验室用电气设备的安全要求.第2-061部分. 实验室原子光谱测量计对热原子化和热电离测量的特殊要求

IEC 61010-2-061:2015 applies to electrically powered laboratory atomic spectrometers with thermal atomization. It has the status of a group safety publication in accordance with IEC Guide 104. This third edition cancels and replaces the second edition published in 2003. It constitutes a technical revision and includes the following change from the second edition: - exclusion of equipment, whose size and weight make unintentional movement unlikely, from the drop test in Clause 8. - notes have been re-phrased according to ISO/IEC Directives.

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomization and ionization