23.020.10 固定容器和罐 标准查询与下载

SANS 53121-2:2009 地面上使用的玻璃钢容器及箱桶.第2部分:复合材料.耐化学性

Gives requirements for chemical resistance of composite materials used for GRP tanks and vessels for storage or processing of fluids, for use above ground. The tanks or vessels may be factory made or site built, with or without lining.

GRP tanks and vessels for use above ground Part 2: Composite materials - Chemical resistance

SANS 53121-3:2009 地面使用的玻璃钢容器.第3部分:设计及工艺

Gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without thermoplastics lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised up to 10 b

GRP tanks and vessels for use above ground Part 3: Design and workmanship

SANS 53121-4:2009 地面上使用的玻璃钢容器.第4部分:交货、安装及维护

Gives requirements for delivery, installation and maintenance of GRP tanks and vessels in accordance with prEN 13121-3.

GRP tanks and vessels for use above ground Part 4: Delivery, installation and maintenance

SANS 53121-1:2009 地面上使用的玻璃钢容器.第1部分:原料-规格条件及验收条件

Gives requirements for specification and acceptance conditions of raw materials for GRP tanks and vessels with or without lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised, for use above ground.

GRP tanks and vessels for use above ground Part 1: Raw materials - Specification conditions and acceptance conditions

DVS 2205-2 Beiblatt 7-2009 由热塑性塑料制成的储罐和设备的计算 立式圆形常压储罐 截环锥底

Calculation of storage tanks and equipment made of thermoplastic plastics Vertical circular atmospheric storage tanks with truncated ring cone bottoms

DVS 2205-2 Beiblatt 8-2009 由热塑性塑料制成的储罐和设备的计算 立式圆形非加压储罐 环支撑锥底示例

Calculation of tanks and equipment made of thermoplastics Vertical circular non-pressurized tank ring support cone bottom example

SANS 53280:2009 用于地上储存冷水的单件及拼装建设的玻璃纤维增强蓄水池规范

Specifies the requirements for rectangular and vertical cylindrical glass reinforced plastics (GRP) one-piece cisterns and rectangular sectional tanks for the storage of water above ground for both domestic and industrial use within the following capacit

Specification for glass fibre reinforced cisterns of one-piece and sectional construction, for the storage, above ground, of cold water

KS B 6602-2009 加油机（手动）

OILER (MANUAL)

ANSI/AWWA D120-2009 热固性玻璃纤维增强塑料罐

This standard describes the composition, performance requirements, construction practices and workmanship, design, and methods of testing thermosetting fiberglass-reinforced plastic (FRP) tanks for the storage of water or other liquids used in water supply service.

Thermosetting Fiberglass-Reinforced Plastic Tanks

ANSI/AWWA D103-2009 储水用加工涂覆螺栓连接钢罐

The purpose of this standard is to provide minimum requirements for the design, construction, inspection, and testing of new cylindrical, factory coated, bolted carbon steel tanks for the storage of water. This standard is only applicable to tanks with a base elevation substantially at ground level.

Factory-Coated Bolted Steel Tanks for Water Storage

ANSI/ASTM D4865:2009 石油燃料系统中静电的产生和耗散指南

Guide For Generation And Dissipation Of Static Electricity In Petroleum Fuel Systems

ANSI/UL 80-2009 燃油炉燃料和其他可燃液体用钢制槽罐的安全性标准(公告日期2008年12月5日)

Deletion of Exception in Stability Test

Standard for Safety for Steel Tanks for Oil-Burner Fuels and Other Combustible Liquids (Bulletin dated December 5, 2008)

DVS 2231-2008 热塑性塑料制成的地上储罐、设备和管道 质量保证指南

"Above-ground tanks, apparatus and piping made of thermoplastics - Guide to quality assurance"

ASTM F991M-04(2008) 对接/排放塞和凸台组件的标准规范[米制]

Standard Specification for Docking/Drain Plug and Boss Assemblies [Metric]

DIN EN 13121-3:2008 地上用GRP槽罐和容器.第3部分:设计和工作质量

This European Standard gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without Thermoplastics lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised up to 10 bar, for use above ground. The terms vessels and tanks as used in this European Standard include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell. In addition to the definitive requirements, this European Standard also requires the items in Clause 5 to be fully documented. This European Standard covers vessels and tanks subject to temperatures between - 40 ℃ and + 120 ℃. NOTE It is possible that future advances in resin technology would allow tanks and vessels to be considered for operating temperatures above + 120 ℃. Should such a situation arise and a manufacturer wishes to take advantage of such developments, then all other requirements of the standard shall be maintained and such tanks and vessels shall only be designed in accordance with the advanced design method given in 7.8.3. Excluded from this European Standard are: -- tanks and vessels for the transport of fluids; -- underground storage tanks; -- spherical vessels; -- vessels and tanks of irregular shape; -- tanks and vessels with double containment; -- tanks and vessels which are subject to the risk of explosion, or failure of which may cause an emission of radioactivity; -- specification for fibre reinforced cisterns of one piece and sectional construction for the storage, above ground, of cold water (see EN 13280:2001).

GRP tanks and vessels for use above ground - Part 3: Design and workmanship; German version EN 13121-3:2008

BS EN 13121-3:2008+A1:2010 地面用玻璃钢槽罐和容器.第3部分:设计和工艺

This European Standard gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without Thermoplastics lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised up to 10 bar, for use above ground. The terms vessels and tanks as used in this European Standard include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell. In addition to the definitive requirements, this European Standard also requires the items in Clause 5 to be fully documented. This European Standard covers vessels and tanks subject to temperatures between – 40 °C and + 120 °C. NOTE It is possible that future advances in resin technology would allow tanks and vessels to be considered for operating temperatures above + 120 °C. Should such a situation arise and a manufacturer wishes to take advantage of such developments, then all other requirements of the standard shall be maintained and such tanks and vessels shall only be designed in accordance with the advanced design method given in 7.8.3. Excluded from this European Standard are: ? tanks and vessels for the transport of fluids; ? underground storage tanks; ? spherical vessels; ? vessels and tanks of irregular shape; ? tanks and vessels with double containment; ? tanks and vessels which are subject to the risk of explosion, or failure of which may cause an emission of radioactivity; ? specification for fibre reinforced cisterns of one piece and sectional construction for the storage, above ground, of cold water (see EN 13280-2001).

GRP tanks and vessels for use above ground. Part 3:Design and workmanship

BS EN 13121-3:2008 地面用GRP槽罐和容器.设计和工艺

This European Standard gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without Thermoplastics lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised up to 10 bar, for use above ground. The terms vessels and tanks as used in this European Standard include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell. In addition to the definitive requirements, this European Standard also requires the items in Clause 5 to be fully documented. This European Standard covers vessels and tanks subject to temperatures between – 40 °C and + 120 °C. NOTE It is possible that future advances in resin technology would allow tanks and vessels to be considered for operating temperatures above + 120 °C. Should such a situation arise and a manufacturer wishes to take advantage of such developments, then all other requirements of the standard shall be maintained and such tanks and vessels shall only be designed in accordance with the advanced design method given in 7.8.3. Excluded from this European Standard are: ? tanks and vessels for the transport of fluids; ? underground storage tanks; ? spherical vessels; ? vessels and tanks of irregular shape; ? tanks and vessels with double containment; ? tanks and vessels which are subject to the risk of explosion, or failure of which may cause an emission of radioactivity; ? specification for fibre reinforced cisterns of one piece and sectional construction for the storage, above ground, of cold water (see EN 13280:2001).

GRP tanks and vessels for use above ground - Part 3: Design and workmanship

NF M88-557-3:2008 地上用玻璃纤维增强塑料(GPR)罐和容器.第3部分:设计和工艺

GRP tanks and vessels for use above ground - Part 3 : design and workmanship.

EN 13121-3:2008 地面气体贮罐(GRP)和容器.第3部分:设计及制造

This European Standard gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without Thermoplastics lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised up to 10 bar, for use above ground. The terms vessels and tanks as used in this European Standard include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell. In addition to the definitive requirements, this European Standard also requires the items in Clause 5 to be fully documented. This European Standard covers vessels and tanks subject to temperatures between – 40 °C and + 120 °C. NOTE It is possible that future advances in resin technology would allow tanks and vessels to be considered for operating temperatures above + 120 °C. Should such a situation arise and a manufacturer wishes to take advantage of such developments, then all other requirements of the standard shall be maintained and such tanks and vessels shall only be designed in accordance with the advanced design method given in 7.8.3. Excluded from this European Standard are:  tanks and vessels for the transport of fluids;  underground storage tanks;  spherical vessels;  vessels and tanks of irregular shape;  tanks and vessels with double containment;  tanks and vessels which are subject to the risk of explosion, or failure of which may cause an emission of radioactivity;  specification for fibre reinforced cisterns of one piece and sectional construction for the storage, above ground, of cold water (see EN 13280:2001).

GRP tanks and vessels for use above ground - Part 3: Design and workmanship Incorporates Amendment A1: 2010

CAN/ULC-S652-2008 用于收集、储存和清除废油的储罐组件标准

1.1 This Standard sets forth the minimum requirements for the adaptation of tank assemblies constructed in accordance with the requirements described in Clause 3.1 for the collection, storage and removal of used oil. 1.2 Used oil tank assemblies covered by this Standard are intended for stationary installation and use in accordance with, but not limited to the following: A National Fire Code of Canada; B CSA-B139, Installation Code for Oil-Burning Equipment; C CCME PN 1326, Environmental Code of Practice for Aboveground and Underground Storage Tank Systems Containing Petroleum and Allied Petroleum Products; and B Regulations of the appropriate authority having jurisdiction.

Standard forTank Assemblies for the Collection, Storage and Removal of Used Oil