23.080 泵 标准查询与下载

T/ZZB 3485-2023 单级双吸离心泵

本文件规定了单级双吸离心泵的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于公称尺寸DN≤1400mm，输送液体温度不大于80 ℃，固体量不大于80 mg/L的清水或物理化学性质类似于水的其它液体的单级双吸离心泵（以下简称泵）。

Single stage double suction centrifugal pump

T/CASME 900-2023 多用途液压泵站技术要求

本文件规定了多用途液压泵站的术语和定义、基本要求、主要部件要求、技术要求、试验方法、检验规则及标志、包装、运输和贮存。

Technical requirements of multi-purpose hydraulic pump station

T/ZXJY 013-2023 输送沥青用齿轮泵

本文件规定了输送沥青用齿轮泵的术语和定义、分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存等。

Gear pump for conveying asphalt

T/ZXJY 014-2023 输送沥青用螺杆泵

本文件规定了输送沥青用螺杆泵的术语和定义、分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

Screw pump for conveying asphalt

T/CASME 844-2023 离心泵用智能机械密封系统应用技术规程

本文件规定了离心泵用智能机械密封系统的术语和定义、总体结构、一般要求、电器安全性能、机械性能、智能密封系统和能耗管理等要求。

Intelligent mechanical sealing system for centrifugal pumps Application Technical Regulations

ISO/CD 15783:2023 无密封旋转动力泵 II 级 规范

Seal-less rotodynamic pumps — Class II — Specification

IEC 60335-2-51:2023 PRV

T/ZZB 3126-2023 暖通空调用管道离心泵

本文件规定了暖通空调用管道离心泵的型式、型号与基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于输送介质温度为0℃～90℃的清水，吸入压力不大于1.0 MPa，工作压力不大于1.6 MPa的暖通空调用管道离心泵（以下简称“泵”）。

Inline centrifugal pump for heating ventilation air conditioning

T/FMTI 0002-2023 核电厂用永磁直驱离心泵

本标准规定了核电厂用永磁直驱离心泵的型式、型号、基本参数、技术要求、试验方法、检验规则和标志、包装、贮存和运输。 其中，基本参数、技术要求、试验方法为本标准的主要内容。

Permanent magnet direct driven centrifugal pump for nuclear power plant

T/CIPR 114-2023 注采井口防冻取样器

本文件规定了注采井口防冻取样器的标记、基本参数、要求、试验方法、检验规则及标志、包装、贮存。 本文件适用于陆地井口配套使用的防冻取样器。

Injection and production wellhead antifreeze sampler

T/ZZB 3063-2023 固液两相流液压式隔膜泵

本文件规定了固液两相流液压式隔膜泵的术语和定义、型式、型号与基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本文件适用于输送温度为-30℃～150℃、黏度为0.3 mm2/s～2000 mm2/s、粒度≤10 mm，干固体含量的质量比≤87％的固液两相流介质的平板隔膜和筒状隔膜的液压式隔膜泵（以下简称“泵”）。

Solid-liquid two-phase flow hydraulic diaphragm pump

T/CASME 476-2023 离心式陶瓷渣浆泵

本文件规定了离心式陶瓷渣浆泵的型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存、成套范围。

Centrifugal ceramic slurry pump

T/HTX 2001-2023 并联自平衡多级离心泵

1　范围 2　规范性引用文件 3　术语和定义 4　型式与基本参数 5　技术要求 6　试验方法 7　检验规则 8　标志、包装、运输与贮存 9　成套范围

Parallel self-balancing multi-stage centrifugal pump

ASTM D5337-23 个人取样泵流量设置和验证的标准实施规程

1.1 This practice describes the setting and verification of flow rate for sampling pumps commonly used for monitoring personal airborne exposures in the workplace. 1.2 This practice includes procedures for using working standard flow meters that are traceable to national or international standards, as well as those that are not. Traceable standards are preferred. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Setting and Verifying the Flow Rate of Personal Sampling Pumps

T/CI 040-2023 单螺杆泵

5　一般要求 5.1　基本要求 泵应符合本标准的要求，并按经规定程序批准的产品图样及技术文件制造。如用户有特殊要求，在考虑本标准规定的同时，应在订单中注明，按供需双方确认的合同制造。 5.2　输送介质条件 泵在下列输送介质条件下应能连续正常运行： ——温度小于或等于80?℃，特种定子可达-20?℃～150?℃（由供需双方另订协议）； ——介质中固体物最大含量按体积计不超过40%（如为粉状微料可达70%），最大粒径不超过转子的偏心距，最大纤维长度不超过40%的转子螺距。

Single screw pumps

T/QGCML 685-2023 大流量便携式潜水泵

本标准规定了大流量便携式潜水泵的术语定义、技术要求、试验方法、检验规则、铭牌、标志、包装、运输及贮存。 本标准适用于大流量便携式潜水泵的生产和检验。

High Flow Portable Submersible Pump

GSO CEN/TR 13932:2023 转子动力泵 管道上入口和出口安装的建议

This CEN Technical Report lays down stipulations relating to installation conditions for sudden change in section or direction (elbows, tee fittings, junctions) and the most widely used accessories at the inlet and outlet of pumps (valves and fittings) in order to minimise the effect of disturbances in the flow of liquid thereby created upstream and downstream from the pump and on the operation of the pump. NOTE 1 The recommendations given in this document permit to solve a majority of the most current cases. These recommendations relate to three aspects of installation: the fitting of the pump to pipework by convergent and divergent pipes; in the case of elbows, tees and branching, their direction with respect to the axis of the pump; the minimum clearances to be adhered to between a disturbing (elbow, valve, etc.) and the mounting flange of the pump. This document applies to the installation of rot dynamic pumps (centrifugal, mixed flow and axial flow) fitted in piping. It applies to pumps having intake diameters equal to or less than 500 mm. The recommendations may be adapted in agreement with the pump manufacturer for intakes having dimensions exceeding 500 mm or for special applications. This document is not applicable to pumps of which the inlet is located in reservoirs, sumps or tanks and which will be dealt with in a subsequent standard. The recommendations in this document are only valid under the following conditions: Newtonian fluids having a maximum viscosity of 2.10-4 m2/s; occluded gas content at pumping temperature and inlet pressure not exceeding 2 % by volume for water and 4 % for other fluids; solids content (small particle size, such as sand) not exceeding 1 % by volume, nor 1 % by weight; in piping with diameters D1 and D2 (see Figure 11), flow rate velocity, should be in the following ranges: 3 m/s to 5 m/s at inlet; 4 m/s to 10 m/s at outlet.

Rotodynamic pumps - Recommendations for fitting of inlet and outlet on piping

GSO EN 17038-1:2023 泵 转子动力泵装置能效指数的鉴定和验证方法 第1部分：能效指数 (EEI) 测试和计算的一般要求和程序

This document describes a methodology to evaluate energy efficiency performance of pump units based on a non-dimensional numerical value called Energy Efficiency Index (EEI). This document covers pump units consisting of: - one single or several rotodynamic water pump(s), including where integrated in other products, and driven by a motor system, consisting of an electrical motor, and either: - a terminal box which only enables to operate the pump unit at constant motor stator frequency and thereby (nearly) constant rotational speed, or - a CDM (Complete Drive Module) which enables to operate the pump unit at variable rotational speed depending on a varying demand of flow rate and/or discharge or differential pressure. NOTE A CDM is also often called VSD (Variable Speed Drive). Pump units as defined above are treated as extended products in respect to their energy efficiency.

Pumps - Methods of qualification and verification of the Energy Efficiency Index for rotodynamic pump units - Part 1: General requirements and procedures for testing and calculation of Energy Efficiency Index (EEI)

T/QGCML 645-2023 自处理阻塞单速泳池水泵技术规范

本标准规定了自处理阻塞单速泳池水泵技术规范的术语定义、产品结构示意图、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于自处理阻塞单速泳池水泵的设计和生产。

Specification for self-clogging single-speed swimming pool pumps

DB31/T 616-2023 泵系统节能改造技术规范

Technical specifications for energy-saving renovation of pump systems