23.080 泵 标准查询与下载

T/CASME 844-2023 离心泵用智能机械密封系统应用技术规程

本文件规定了离心泵用智能机械密封系统的术语和定义、总体结构、一般要求、电器安全性能、机械性能、智能密封系统和能耗管理等要求。

Intelligent mechanical sealing system for centrifugal pumps Application Technical Regulations

ISO/CD 15783:2023 无密封旋转动力泵 II 级 规范

Seal-less rotodynamic pumps — Class II — Specification

IEC 60335-2-51:2023 PRV

T/ZZB 3126-2023 暖通空调用管道离心泵

本文件规定了暖通空调用管道离心泵的型式、型号与基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于输送介质温度为0℃～90℃的清水，吸入压力不大于1.0 MPa，工作压力不大于1.6 MPa的暖通空调用管道离心泵（以下简称“泵”）。

Inline centrifugal pump for heating ventilation air conditioning

T/FMTI 0002-2023 核电厂用永磁直驱离心泵

本标准规定了核电厂用永磁直驱离心泵的型式、型号、基本参数、技术要求、试验方法、检验规则和标志、包装、贮存和运输。 其中，基本参数、技术要求、试验方法为本标准的主要内容。

Permanent magnet direct driven centrifugal pump for nuclear power plant

T/CIPR 114-2023 注采井口防冻取样器

本文件规定了注采井口防冻取样器的标记、基本参数、要求、试验方法、检验规则及标志、包装、贮存。 本文件适用于陆地井口配套使用的防冻取样器。

Injection and production wellhead antifreeze sampler

T/ZZB 3063-2023 固液两相流液压式隔膜泵

本文件规定了固液两相流液压式隔膜泵的术语和定义、型式、型号与基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本文件适用于输送温度为-30℃～150℃、黏度为0.3 mm2/s～2000 mm2/s、粒度≤10 mm，干固体含量的质量比≤87％的固液两相流介质的平板隔膜和筒状隔膜的液压式隔膜泵（以下简称“泵”）。

Solid-liquid two-phase flow hydraulic diaphragm pump

T/CASME 476-2023 离心式陶瓷渣浆泵

本文件规定了离心式陶瓷渣浆泵的型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存、成套范围。

Centrifugal ceramic slurry pump

T/HTX 2001-2023 并联自平衡多级离心泵

1　范围 2　规范性引用文件 3　术语和定义 4　型式与基本参数 5　技术要求 6　试验方法 7　检验规则 8　标志、包装、运输与贮存 9　成套范围

Parallel self-balancing multi-stage centrifugal pump

ASTM D5337-23 个人取样泵流量设置和验证的标准实施规程

1.1 This practice describes the setting and verification of flow rate for sampling pumps commonly used for monitoring personal airborne exposures in the workplace. 1.2 This practice includes procedures for using working standard flow meters that are traceable to national or international standards, as well as those that are not. Traceable standards are preferred. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Setting and Verifying the Flow Rate of Personal Sampling Pumps

T/CI 040-2023 单螺杆泵

5　一般要求 5.1　基本要求 泵应符合本标准的要求，并按经规定程序批准的产品图样及技术文件制造。如用户有特殊要求，在考虑本标准规定的同时，应在订单中注明，按供需双方确认的合同制造。 5.2　输送介质条件 泵在下列输送介质条件下应能连续正常运行： ——温度小于或等于80?℃，特种定子可达-20?℃～150?℃（由供需双方另订协议）； ——介质中固体物最大含量按体积计不超过40%（如为粉状微料可达70%），最大粒径不超过转子的偏心距，最大纤维长度不超过40%的转子螺距。

Single screw pumps

T/QGCML 685-2023 大流量便携式潜水泵

本标准规定了大流量便携式潜水泵的术语定义、技术要求、试验方法、检验规则、铭牌、标志、包装、运输及贮存。 本标准适用于大流量便携式潜水泵的生产和检验。

High Flow Portable Submersible Pump

GSO EN 17038-1:2023 泵 转子动力泵装置能效指数的鉴定和验证方法 第1部分：能效指数 (EEI) 测试和计算的一般要求和程序

This document describes a methodology to evaluate energy efficiency performance of pump units based on a non-dimensional numerical value called Energy Efficiency Index (EEI). This document covers pump units consisting of: - one single or several rotodynamic water pump(s), including where integrated in other products, and driven by a motor system, consisting of an electrical motor, and either: - a terminal box which only enables to operate the pump unit at constant motor stator frequency and thereby (nearly) constant rotational speed, or - a CDM (Complete Drive Module) which enables to operate the pump unit at variable rotational speed depending on a varying demand of flow rate and/or discharge or differential pressure. NOTE A CDM is also often called VSD (Variable Speed Drive). Pump units as defined above are treated as extended products in respect to their energy efficiency.

Pumps - Methods of qualification and verification of the Energy Efficiency Index for rotodynamic pump units - Part 1: General requirements and procedures for testing and calculation of Energy Efficiency Index (EEI)

GSO CEN/TR 13932:2023 转子动力泵 管道上入口和出口安装的建议

This CEN Technical Report lays down stipulations relating to installation conditions for sudden change in section or direction (elbows, tee fittings, junctions) and the most widely used accessories at the inlet and outlet of pumps (valves and fittings) in order to minimise the effect of disturbances in the flow of liquid thereby created upstream and downstream from the pump and on the operation of the pump. NOTE 1 The recommendations given in this document permit to solve a majority of the most current cases. These recommendations relate to three aspects of installation: the fitting of the pump to pipework by convergent and divergent pipes; in the case of elbows, tees and branching, their direction with respect to the axis of the pump; the minimum clearances to be adhered to between a disturbing (elbow, valve, etc.) and the mounting flange of the pump. This document applies to the installation of rot dynamic pumps (centrifugal, mixed flow and axial flow) fitted in piping. It applies to pumps having intake diameters equal to or less than 500 mm. The recommendations may be adapted in agreement with the pump manufacturer for intakes having dimensions exceeding 500 mm or for special applications. This document is not applicable to pumps of which the inlet is located in reservoirs, sumps or tanks and which will be dealt with in a subsequent standard. The recommendations in this document are only valid under the following conditions: Newtonian fluids having a maximum viscosity of 2.10-4 m2/s; occluded gas content at pumping temperature and inlet pressure not exceeding 2 % by volume for water and 4 % for other fluids; solids content (small particle size, such as sand) not exceeding 1 % by volume, nor 1 % by weight; in piping with diameters D1 and D2 (see Figure 11), flow rate velocity, should be in the following ranges: 3 m/s to 5 m/s at inlet; 4 m/s to 10 m/s at outlet.

Rotodynamic pumps - Recommendations for fitting of inlet and outlet on piping

T/QGCML 645-2023 自处理阻塞单速泳池水泵技术规范

本标准规定了自处理阻塞单速泳池水泵技术规范的术语定义、产品结构示意图、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于自处理阻塞单速泳池水泵的设计和生产。

Specification for self-clogging single-speed swimming pool pumps

DB31/T 616-2023 泵系统节能改造技术规范

Technical specifications for energy-saving renovation of pump systems

T/CAS ES230134001-2022 工业品质量分级评价规则 卧式自吸离心泵

1　范围 本文件规定了卧式自吸离心泵组质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于工业装置用卧式自吸离心泵组质量分级评价活动。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 3216  回转动力泵  水力性能验收试验  1级、2级和3级 GB/T 29529  泵的噪声测量与评价方法 GB/T 29531  泵的振动测量与评价方法 GB 32284—2015  石油化工离心泵能效限定值及能效等级 JB/T 6664—2017  自吸泵 SH/T 3140—2011  石油化工中、轻载荷离心泵工程技术规范 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则  通则 

Rules for quality grading and evaluating of industrial products—The horizontal type self-priming centrifugal pump

T/CAS ES230902001-2022 工业品质量分级评价规则 机动往复泵

1　范围 本文件规定了机动往复泵质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于机动往复泵质量分级评价活动。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 7784  机动往复泵试验方法 GB/T 7785  往复泵分类和名词术语 GB/T 9069  往复泵噪声声功率级的测定 GB/T 9234  机动往复泵 GB/T 13363  化工用往复泵技术条件 GB/T 13364  往复泵机械振动测试方法 JB/T 6538  往复式增压泵 JB/T 8697  隔膜泵 JB/T 9087  油田用往复式油泵、注水泵 JB/T 9088  往复式杂质泵 JB/T 9089  试压泵 SH/T 3141  石油化工往复泵工程技术规范 SY/T 5138  三缸单作用钻井泵 SY/T 6462  油田用注聚合物泵 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则  通则  API 674  Positive Displacement Pumps- Reciprocating

Rules for quality grading and evaluating of industrial products—Power reciprocating pump

T/CAS ES230910001-2022 工业品质量分级评价规则 泵 计量泵

1　范围 本文件规定了计量泵质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于计量泵质量分级评价活动。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 7782  计量泵 GB/T 7784  机动往复泵试验方法 GB/T 7785  往复泵分类和名词术语 GB/T 9234  机动往复泵 JB/T 6910  微量计量泵 SH/T 3142  石油化工计量泵工程技术规范 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则  通则  API STD 675  Positive Displacement Pumps- Controlled Volume

Rules for quality grading and evaluating of industrial products—Pump—Metering pump

T/ZZB 2819-2022 离心式高压液氨泵

本文件规定了离心式高压液氨泵的型式、型号与基本参数、基本要求、技术要求、试验方法、检验规则以及标志、包装、运输、贮存和质量承诺。 本文件适用于输送液氨介质温度在-30 ℃～132 ℃，提升压力在10 MPa以上的离心式液氨泵（以下简称泵）。其他输送类似介质的离心泵可参照使用。

High pressure ammonia centrifugal pump