23.100 流体动力系统 标准查询与下载
共找到 84 条与 流体动力系统 相关的标准，共 6 页
本标准规定了泵受压铸钢件的X、γ射线检测方法和铸钢件的缺陷等级分类。 本标准适用于厚度5 mm~300 mm泵受压铸钢件采用胶片记录被检工件的射线检测；配套的管件和法兰等受压铸钢件的射线检测也可参照本标准执行。
Nondestructive testing method for pump parts.Radiographic testing method compression steel casting for pump
- ICS
- 23.100
- CCS
- J71
- 发布
- 2015-10-10
- 实施
- 2016-03-01
本标准规定了微量计量泵的型式与基本参数、技术要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于输送温度为-30℃~60℃、黏度为0.3 mm/s~100 mm/s、流量≤5 000 mL/h，不含固体颗粒的腐蚀与非腐蚀液体的微量柱塞计量泵、微量隔膜计量泵、微量平流计量泵和微量电磁计量泵。
Small flow metering pump
- ICS
- 23.100
- CCS
- J71
- 发布
- 2015-10-10
- 实施
- 2016-03-01
本标准规定了电站空冷机组清洗装置的术语和定义、构成、型号、形式、基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于额定排出压力为8 MPa~15 MPa，工作介质为常温除盐水的电站空冷机组清洗装置(以下简称清洗装置)。
Cleaning devices for power plant air cooling condenser units
- ICS
- 23.100
- CCS
- J70
- 发布
- 2015-07-14
- 实施
- 2016-01-01
本标准规定了喷射设备常用的名词术语。本标准适用于喷射设备的设计、制造、贸易，制定其他相关标准，编写有关技术文件与报告，编写或翻译书籍文献、教材、样本以及进行技术交流。
Terminology for jet equipment
- ICS
- 23.100
- CCS
- J70
- 发布
- 2015-07-14
- 实施
- 2016-01-01
Power station air cooling unit cleaning device
- ICS
- 23.100
- CCS
- J70
- 发布
- 2015-07-14
- 实施
- 2016-01-01
The purpose of this guide is to establish, in a general way, suitable procedures for commissioning a) non-reversible hydraulic machines without movable wicket-gates, i.e. storage pumps; b) reversible hydraulic machines with fixed blade impellers and without movable wicket-gates, operating as pumps; c) reversible hydraulic machines with fixed blade impellers and with movable wicket-gates, operating as pumps; d) reversible hydraulic machines with adjustable impeller blades and movable wicket-gates, operating as pumps. and associated equipment. This guide also indicates how such machines and equipment should be operated and maintained. This guide applies to storage pumps and reversible pump-turbines of all types, especially to large units coupled to electrical motor-generators. The guide excludes matters of purely commercial interest, except those inextricably bound up with the conduct of commissioning, operation and maintenance. It is understood that a document of this type will be binding only if, and to the extent that, both contract parties have agreed upon it. Wherever the guide specifies that documents, drawings or information are to be supplied by a manufacturer (or by manufacturers), each individual manufacturer shall be required to furnish the appropriate information for his own supply only. The guide is not concerned with water conduits, gates, valves, drainage pumps, cooling water equipment, generators, etc., except where they cannot be separated from the machine and its equipment. It is assumed that the turbine of the set or the pump-turbine operating as turbine has been commissioned beforehand in accordance with IEC Publication 545: Guide for Commissioning, Operation and Maintenance of Hydraulic Turbines, where applicable. Where this is not possible, an individual commissioning procedure shall be established at an early stage of plan design.
Guide for commissioning, operation and maintenance of storage pumps and of pump-turbines operating as pumps
- ICS
- 23.100
- CCS
- 发布
- 2014-12-25
- 实施
本标准规定了超高压泵的型式与基本参数、技术要求、试验方法、检验规则、标志、包装和贮存。本标准适用于额定排出压力为100 MPa~1 000 MPa的机动往复泵和液动超高压增压器(以下简称泵),输送介质为常温清水或油品,工作环境温度为常温、相对湿度不大于85%的场合。
Ultra-high pressure pump
- ICS
- 23.100
- CCS
- J71
- 发布
- 2014-07-09
- 实施
- 2014-11-01
本标准规定了自控试压机的型式与基本参数、技术要求、试验方法、检验规则、标志、包装、贮存和运输。本标准适用于额定工作压力≤400 MPa,工作介质为5℃~60℃的清水、乳化液或运动粘度不超过45 mm/s的油品,主机为试压泵或超高压泵的自控试压机。
Automatic control pressure test system
- ICS
- 23.100
- CCS
- J71
- 发布
- 2014-07-09
- 实施
- 2014-11-01
本标准规定了电动、手动试压泵的基本参数,技术条件,试验方法,检验规则,标志、包装和贮存。本标准适用于额定排出压力至200 MPa,工作介质为温度5℃~60℃的清水、乳化液或运动粘度不超过45 mm/s的油品的电动、手动试压泵(以下简称泵)。
Pressure testing pump
- ICS
- 23.100
- CCS
- J71
- 发布
- 2014-07-09
- 实施
- 2014-11-01
Performance test methods for industrial oil cleaner
- ICS
- 23.100
- CCS
- 发布
- 2013-12-30
- 实施
本标准规定了液体喷砂机的术语和定义、技术要求、试验与检测、检验规则和标志、包装、运输和贮存，以及喷砂质量和判定依据。本标准适用于系统工作压力不大于0.8 MPa，以磨液为介质，以表面处理为目的的液体喷砂机(以下简称喷砂机)。
Wet blasting equipment
- ICS
- 23.100
- CCS
- J61;J70
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了机场跑道除胶设备的型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于额定排除压力为100 MPa~250 MPa，主机泵额定功率为110 kW~275 kW，工作介质为常温清水，集主泵机组、平面清洗器和专用车为一体的各种型式的车载式机场跑道除胶设备(以下简称“除胶车”)。
Airport runway rubber-removal cleaning vehicle
- ICS
- 23.100
- CCS
- V56
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了高温、热水清洗机型式、基本参数、技术要求、试验方法、标志、包装和贮存。本标准适用于额定排出压力不高于35 MPa、额定流量不大于25 L/min、工作温度不高于150°C、工作介质为不含颗粒常温清水或清洗剂与清水的混合液的汽油机、柴油机及电动机为动力的高温和热水清洗机(以下简称“清洗机”)。
High temperature、 hot water cleaning machine
- ICS
- 23.100
- CCS
- J70
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了用机动往复泵作动力的微、小型清洗机的基本参数、技术要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于泵额定排出压力为3MPa～40MPa、额定流量为2.5L/min～90L/min、工作介质为常温清水或运动粘度不大于45mm²/s、不含颗粒、无腐蚀性的清洗剂混合液的微、小型水射流清洗机（以下简称清洗机）。
Mini and small type cleaning machine
- ICS
- 23.100
- CCS
- J70
- 发布
- 2012-05-24
- 实施
- 2012-11-01
本规范规定了石油化工粉体工程的工艺系统设计和机械设备、自动控制的基本原则，以及粉体工程安全、环保、节能等方面的基本要求。 本规范适用于石油化工新建或扩建粉体工程的设计。
Design specification of material handling in petrochemical engineering
- ICS
- 23.100
- CCS
- P72
- 发布
- 2011-05-18
- 实施
- 2011-06-01
This document prescribes mandatory requirements for the design and installation of electrical power systems. This document is intended to assist engineers and designers in those areas not specifically referenced in other company’s’ standards or material specification , etc. This document may not be attached to nor made a part of purchase orders.
Power System Design – Basic Power System Design Criteria
- ICS
- 23.100
- CCS
- 发布
- 2011-04-12
- 实施
本规定规定了石油化工搅拌器的设计、制造、检验和试验等方面的基本要求。 本规定适用于石油化工用搅拌器的工程设计及设备采购。
Engineering specification of agitators in petrochemical industry
- ICS
- 23.100
- CCS
- P72;G93
- 发布
- 2007-01-25
- 实施
- 2007-07-01
Guide for commissioning, operation and maintenance of storage pumps and of pump-turbines operating as pumps
- ICS
- 23.100
- CCS
- 发布
- 2006-05-10
- 实施
