共找到 460 条与 真空技术 相关的标准,共 31 页
This part of ISO 9803 specifies mounting dimensions for vacuum pipeline fittings (elbows, tees and crosses) of knife-edge flanges for nominal bores from 16 mm to 200 mm.
Vacuum technology -- Mounting dimensions of pipeline fittings -- Part 2: Knife-edge flange type
This part of ISO 9803 specifies mounting dimensions for vacuum pipeline fittings (elbows, tees and crosses) of non-bakable and non knife-edge flange for nominal bores from 10 mm to 250 mm of the R5 series.
Vacuum technology -- Mounting dimensions of pipeline fittings -- Part 1: Non knife-edge flange type
This International Standard defines dimensions of right-angle valves that are compatible with the mounting dimensions of elbows defined in ISO 9803-1 and ISO 9803-2. This International Standard covers right-angle valves with flanges defined in ISO 2861-1, ISO 1609 and ISO 3669. ISO 3669 lists two flange series: — preferred series, and — secondary series. This International Standard covers only the valves with flanges of the secondary series.
Vacuum technology -- Right-angle valve -- Dimensions and interfaces for pneumatic actuator
本标准规定了真空磁流体动密封件的型号编制、型式、尺寸、技术要求、标志、包装、贮存和运输。 本标准适用于外部压力为1×10Pa(大气压),真空室压力为1×10Pa~1×10Pa(大气压)的真空设备的动密封。
Ferrofluid vacuum rotary feedthroughs
本标准规定了磁悬浮分子泵的术语和定义,型式与基本参数,技术要求,测试方法,检验规则,标志、包装、运输和贮存。 本标准适用于具有前级泵的磁悬浮分子泵(以下简称磁浮泵)。
Vacuum technology.Magnetic levitated turbomolecular pump
本标准规定了湿式罗茨真空泵的术语和定义、型式与基本参数、技术要求、抽样及判定方法、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于湿式罗茨真空泵(以下简称泵)。
Vacuum technology.Wet roots vacuum pump
本标准规定了往复真空泵的术语和定义、型式与基本参数、技术要求、抽样及判定方法、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于抽除不含颗粒的气体的往复式真空泵(以下简称泵)。
Piston vacuum pump
Vacuum technology. Standard methods for measuring vacuum pump performance. Part 1. General description
Vacuum technology. Turbomolecular pumps. Measurement of rapid shutdown torque
Scope is not provided for this standard
Vacuum technology -- Turbomolecular pumps -- Measurement of performance characteristics
Scope is not provided for this standard
Vacuum technology -- Flange dimensions
Scope is not provided for this standard
Vacuum technology -- Bakable flanges -- Part 2: Dimensions of knife-edge flanges
Scope is not provided for this standard
Vacuum gauges -- Definitions and specifications for quadrupole mass spectrometers
Scope is not provided for this standard
Vacuum technology -- Dimensions of clamped-type quick-release couplings
Vacuum technology -- Standard methods for measuring vacuum-pump performance -- Part 2: Positive displacement vacuum pumps
Vacuum technology -- Standard methods for measuring vacuum-pump performance -- Part 1: General description
本标准规定了夹套圆筒刮板干燥机的型号与标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于对悬浮液浆状、糊状物料进行干燥的夹套圆筒刮板干燥机(以下简称干燥机)。
Scraper drum dryer
本标准规定了旋流式制粒包衣干燥机的型号与标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于对粉状、微粒状等物料进行制粒包衣干燥的旋流式制粒包衣干燥机(以下简称包衣干燥机)。
Turbojet fluid-bed granulator coater and dryer
本标准规定了气流干燥机的型式与标记、技术要求、试验方法、检验规则及标志、使用说明书、包装、运输和贮存。 本标准适用于对粉状、微粒状物料进行干燥的气流干燥机(以下简称干燥机)。
Flash dryers
JB/T 8105的本部分规定了金属密封真空规管接头的型式与结构尺寸及技术要求。 本部分适用于可烘烤真空系统中真空测量用金属密封的规管接头。
Vacuum technology.Connector of vacuum gauges.Part 2: Metal seal
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号