25.160.30 焊接设备 标准查询与下载

KS B ISO 15615-2019 气焊设备 - 用于焊接 切割和相关工艺的乙炔歧管系统 - 高压设备的安全要求

Gas welding equipment — Acetylene manifold systems for welding, cutting and allied processes — Safety requirements in high-pressure devices

KS B ISO 15615-2019(2023) 气焊设备.焊接、切割和相关工艺用乙炔歧管系统.高压装置的安全要求

Gas welding equipment — Acetylene manifold systems for welding, cutting and allied processes — Safety requirements in high-pressure devices

KS B ISO 5183-2-2019 电阻点焊 - 电极适配器 公锥1:10 - 第2部分:平行柄固定用于末端推力电极

Resistance spot welding — Electrode adaptors, male taper 1：10 —Part 2: Parallel shank fixing for end-thrust electrodes

KS C 9001-2019 弧焊机通用规则

General rules for Arc Welder

CSA C22.2 No.60974-1-2019 弧焊设备 第1部分：焊接电源

1 Domaine d’application La présente partie de l’IEC 60974 s'applique aux sources de courant de soudage à l'arc et aux procédés connexes conçus pour un usage industriel et professionnel qui sont alimentés sous une tension ne dépassant pas 1 000 V, alimentés par batterie ou entraînés par des moyens mécaniques. Le présent document spécifie les exigences de sécurité et de fonctionnement des sources de courant de soudage et des systèmes de coupage par plasma. Le présent document ne s'applique pas aux sources de courant de soudage et de coupage à l'arc à service limité qui sont utilisées essentiellement par des non professionnels et qui sont conçues selon l’IEC 60974-6. Le présent document inclut les exigences relatives aux sources de courant de soudage alimentées par batterie et aux blocs de batteries qui sont donnés à l’Annexe O. Le présent document ne s’applique pas aux essais des sources de courant pendant l’entretien périodique ou après réparation. NOTE 1 Des procédés connexes typiques sont le coupage à l'arc électrique et la projection à l'arc électrique. NOTE 2 Des systèmes en courant alternatif possédant une tension nominale comprise entre 100 V et 1 000 V sont présentés dans le Tableau 1 de l’IEC 60038:2009. NOTE 3 Le présent document ne contient pas les exigences de compatibilité électromagnétique (CEM).

Matériel de soudage à l’arc — Partie 1 : Sources de courant de soudage

BS EN IEC 60974-7:2019 弧焊设备 焊枪

What is BS EN IEC 60974-7- Arc welding equipment about? BS EN IEC 60974 series covers arc welding equipment. BS EN IEC 60974-7 is one of the parts of a series of documents that specifies safety and construction requirements for torches used for arc welding and allied processes. BS EN IEC 60974 is applicable to manual, mechanically guided, air-cooled, liquid-cooled, motorized, spool-on, and fume extraction torches. It is also applicable to a cable hose assembly connected between a power source and ancillary equipment. Note: BS EN IEC 60974-7 is not applicable to electrode holders for manual metal arc welding or air-arc cutting/gouging. Who is BS EN IEC 60974-7- Arc welding equipment for? BS EN IEC 60974-8 on arc welding equipment is applicable to: Construction, automotive, mechanical Industries Sheet metal manufacturers Manufacturers of pressure vessels Manufacturers of aircraft & aerospace Shipbuilding industry Welding equipment manufacturers

Arc welding equipment - Torches

BS EN ISO 9090:2019 气焊及相关工艺设备的气密性

What is ISO 9090 - Gas tightness of equipment for gas welding about?   ISO 9090 is an International Standard that discusses equipment for gas welding, cutting and allied processes.    ISO 9090 specifies the maximum external gas leakage rates which are acceptable for equipment used for welding, cutting, and allied processes and provides the procedures of measurement. Compliance with ISO 9090 can help you achieve a good weld for optimal performance of the end-application.     ISO 9090 is applicable to individual components which are used in the gas supply to a blowpipe from the connecting point of ...

Gas tightness of equipment for gas welding and allied processes

EN ISO 9090:2019 气焊和相关工艺设备气密性

This document specifies the maximum external gas leakage rates which are acceptable for equipment used for welding, cutting and allied processes and provides the procedures of measurement. It applies to individual components which are used in the gas supply to a blowpipe from the connecting point of the hose (outlet of the cylinder valve or connecting point to a gas supply plant). It does not apply to gas supply plant. NOTE Specific requirements on the test method and conditions/procedure for measurement of the maximum external leakages can be given in individual standards, e.g. ISO 9012 for air-aspirated hand blowpipes. Concerning the method and the conditions to be applied, the individual standard takes precedence over this document. The maximum external leakages according to this document apply.

Gas tightness of equipment for gas welding and allied processes (ISO 9090:2019)

ISO 9090:2019 气焊和相关工艺设备气密性

This document specifies the maximum external gas leakage rates which are acceptable for equipment used for welding, cutting and allied processes and provides the procedures of measurement. It applies to individual components which are used in the gas supply to a blowpipe from the connecting point of the hose (outlet of the cylinder valve or connecting point to a gas supply plant). It does not apply to gas supply plant. NOTE Specific requirements on the test method and conditions/procedure for measurement of the maximum external leakages can be given in individual standards, e.g. ISO 9012 for air-aspirated hand blowpipes. Concerning the method and the conditions to be applied, the individual standard takes precedence over this document. The maximum external leakages according to this document apply.

Gas tightness of equipment for gas welding and allied processes

EN ISO 3821:2019 气焊设备.焊接,切割和相关工艺用橡胶软管

This document specifies requirements for rubber hoses (including twin hoses) for welding, cutting and allied processes. This document specifies requirements for rubber hoses for normal duty of 2 MPa (20 bar) and light duty [limited to hoses for maximum working pressure of 1 MPa (10 bar) and with bore up to and including 6,3 mm]. This document applies to hoses operated at temperatures −20 °C to +60 °C and used in: — gas welding and cutting; — arc welding under the protection of an inert or active gas; — processes allied to welding and cutting, in particular, heating, brazing, and metallization. This document does not specify requirements for hose assemblies; these are detailed in ISO 8207. This document applies neither to thermoplastics hoses nor to hoses used for high pressure [>0,15 MPa (>1,5 bar)] acetylene.

Gas welding equipment - Rubber hoses for welding, cutting and allied processes (ISO 3821:2019, Corrected version 2021-05)

T/ZZB 1163-2019 智能型气体保护焊机

本标准规定了智能型气体保护焊机的术语和定义、型号与参数、基本要求、技术要求、试验方法、检验规则、标志、随机文件、包装、运输、贮存和质量承诺。 本标准适用于额定最大焊接电流为200A及以下，熔化极的智能型气体保护焊机（以下简称焊机）。

Intelligent gas shielded welding machine

BS EN IEC 60974-2:2019 弧焊设备 液体冷却系统

What is BS EN IEC 60974-2- Liquid cooling systems in arc welding about?    IEC 60974 series discusses arc welding equipment. The main aim of the IEC 60974 series is to provide manufacturers with best industry welding practices to achieve a good weld.     BS EN IEC 60974-2 is the second part in the series that specifies safety and construction requirements for industrial and professional liquid cooling systems used in arc welding and allied processes (electric arc cutting and arc spraying) to cool torches.   BS EN IEC 60974-2 a pplicable to liquid cooling systems which are separated from the welding equipment or built-in housed in a single enclosure with other welding equipment.   Note : BS EN IEC 60974-2 does not include electromagnetic compatibility (EMC) requirements that are given in IEC 60974-10 and is not applicable to refrigerate...

Arc welding equipment. Liquid cooling systems

ISO 5171:2019 气体焊接设备 - 用于焊接 切割和相关工艺的压力表

This document specifies requirements for Bourdon-tube pressure gauges normally used with compressed gas systems at pressures up to 30 MPa (300 bar) in welding, cutting and allied processes. It also covers use for dissolved acetylene and for liquefied gases under pressure. It does not cover gauges for acetylene in acetylene-manufacturing plants.

Gas welding equipment — Pressure gauges used in welding, cutting and allied processes

IEC 60974-3:2019 电弧焊接设备 - 第3部分:弧形和稳定设备

Arc welding equipment - Part 3: Arc striking and stabilizing devices

IEC 60974-7:2019 电弧焊接设备 - 第7部分:手电筒

Arc welding equipment - Part 7: Torches

IEC 60974-1:2017+AMD1:2019 CSV 弧焊设备第1部分:焊接电源

Arc welding equipment - Part 1: Welding power sources

IEC 60974-1:2017/AMD1:2019 弧焊设备第1部分:焊接电源

Arc welding equipment - Part 1: Welding power sources

IEC 60974-1:2019 弧焊设备第13部分:焊接回流夹

This part of IEC 60974 is applicable to power sources for arc welding and allied processes designed for industrial and professional use@ and supplied by a voltage not exceeding 1000 V@ battery supplied or driven by mechanical means. This document specifies safety and performance requirements of welding power sources and plasma cutting systems. This document is not applicable to limited duty arc welding and cutting power sources which are designed mainly for use by laymen and designed in accordance with IEC 60974-6. This document includes requirements for battery-powered welding power sources and battery packs@ which are given in Annex O. This document is not applicable to testing of power sources during periodic maintenance or after repair. NOTE 1 Typical allied processes are electric arc cutting and arc spraying. NOTE 2 AC systems having a nominal voltage between 100 V and 1000 V are given in Table 1 of IEC 60038:2009. NOTE 3 This document does not include electromagnetic compatibility (EMC) requirements.

Arc welding equipment - Part 13: Welding current return clamp

ISO 7289:2018 气焊设备.切割和相关工艺焊接用带截止阀的快接管接头

This document defines the specifications and the type tests for quick-action couplings with shut-off valves. It applies to quick-action couplings used between the regulator and the torch in equipment for gas welding, cutting and allied processes. This document applies to cases where these couplings are used with hoses in accordance with ISO 3821 or threaded unions in accordance with ISO/TR 28821.

Gas welding equipment — Quick-action couplings with shut-off valves for welding, cutting and allied processes

KS B ISO 15616-2-2018 用于高品质焊接和切割的二氧化碳激光束机的接受测试 - 第二部分:静态和动态精度的测量

Acceptance tests for CO 2 - laser beam machines for high quality welding and cutting — Part 2: Measurement of static and dynamic accuracy