29.060 电线和电缆 标准查询与下载

AECMA PREN 3475-809-2007 航空航天系列.航空用电缆.测试方法.第809部分:抗非平衡性.版本P1

Aerospace series Cables, electrical, aircraft use Test methods Part 809: Resistance unbalance Edition P 1

AECMA PREN 3475-802-2007 航空航天系列.航空用电缆.测试方法.第802部分:非平衡电容.版本P2

Aerospace Series Cables, Electrical, Aircraft Use Test Methods Part 802: Capacitance Unbalance Edition P 2

DLA DSCC-DWG-04044 REV A-2007 200度600伏,铜导体镀银,聚四氟乙烯/聚酰亚胺隔热,轻重量尼龙编织复合材料电气线材

This drawing covers the performance characteristics for a composite wire using a PTFE/polyimide tape wrap insulation system, with a light weight stranded conductor. The polyimide tape should be hydrolysis resistant.

WIRE, ELECTRICAL, COMPOSITE, POLYTETRAFLUOROETHYLENE/POLYIMIDE INSULATED, NORMAL WEIGHT, NICKEL COATED, HIGH STRENGTH OR ULTRA HIGH STRENGTH COPPER ALLOY, 260癈, 600 VOLT

DLA DSCC-DWG-04043 REV A-2007 200度600伏,高强度或超高强度铜合金镀银,聚四氟乙烯/聚酰亚胺隔热,正常重量尼龙编织复合材料电气线材

This drawing covers the performance characteristics for a composite wire using a PTFE/polyimide tape wrap insulation system, with a light weight stranded conductor. The polyimide tape should be hydrolysis resistant.

WIRE, ELECTRICAL, COMPOSITE, POLYTETRAFLUOROETHYLENE/POLYIMIDE INSULATED, NORMAL WEIGHT, SILVER COATED, HIGH STRENGTH OR ULTRA HIGH STRENGTH COPPER ALLOY, 200癈, 600 VOLT

DLA DSCC-DWG-07021-2007 50欧姆,通称直径为1.625英寸低介电损耗的,半刚性波纹外导体同轴射频电缆

1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Helically corrugated inner conductor with outside diameter of .693 +.008 inch. Strip thickness of .010 inch nominal, minor diameter of .626 +.012 inch, and pitch of .400 + .004 inch. 4. The dielectric material shall be CELLFLEX® or equivalent. (CELLFLEX is a registered trade mark of Radio Frequency Systems (RFS)).

CABLES, RADIO FREQUENCY, COAXIAL, SEMIRIGID CORRUGATED OUTER CONDUCTOR, LOW LOSS DIELECTRIC, 1.625 INCH NOMINAL DIAMETER, 50 OHMS

DLA DSCC-DWG-04045 REV A-2007 200度600伏,铜导体镀银,聚四氟乙烯/聚酰亚胺隔热,轻重量尼龙编织复合材料电气线材

This drawing covers the performance characteristics for a composite wire using a PTFE/polyimide tape wrap insulation system, with a light weight stranded conductor. The polyimide tape should be hydrolysis resistant.

WIRE, ELECTRICAL, COMPOSITE, POLYTETRAFLUOROETHYLENE/POLYIMIDE INSULATED, LIGHT WEIGHT, SILVER COATED, COPPER CONDUCTOR, 200癈, 600 VOLT

DLA DSCC-DWG-04038 REV A-2007 600伏200度镀银铜导体正常体重聚四氟乙烯/聚酰亚胺隔热尼龙编织复合材料电线

This drawing covers the performance characteristics for a composite wire using a PTFE/polyimide tape wrap insulation system, with a normal weight nickel coated copper stranded conductor. The polyimide tape should be hydrolysis resistant.

WIRE, ELECTRICAL, COMPOSITE, POLYAMIDE BRAID, POLYTETRAFLUOROETHYLENE/POLYIMIDE INSULATED, NORMAL WEIGHT, NICKEL COATED, COPPER CONDUCTOR, 260癈, 600 VOLT

GSO IEC 60811-1-1:2007 电缆绝缘和护套材料的通用试验方法 第 (1) 部分：一般应用方法 第 (1) 部分：测量厚度和总体尺寸 测定机械性能的试验

The standard to be approved by GSO specifies the test methods to be used for testing polymeric insulating and sheathing materials of electric cables for power distribution and telecommunications including cables used on ships.

Common test methods for insulating and sheathing materials of electrical cabels - Part1: Methods of general application - Section 1:Measurement of thicness and overall dimensions – Tests for Determining the Mechanical Properties

NAVY MIL-DTL-24643 B VALID NOTICE 1-2007 船舷用带电低烟雾电缆和绳索总说明书

MIL-DTL-24643B, dated 22 August 2002, has been reviewed and determined to be valid for use in acquisition.

Cables and Cords, Electric, Low Smoke, for Shipboard Use, General Specification for

NAVY MIL-DTL-915 G VALID NOTICE 1-2007 舷侧用电缆总说明书

MIL-DTL-915G, dated 22 August 2002, has been reviewed and determined to be valid for use in acquisition.

CABLE, ELECTRICAL, FOR SHIPBOARD USE, GENERAL SPECIFICATION FOR

NAVY QPL-AS81044-17-2007 交联聚烯烃及交联烷烃酰亚胺聚合物的铜或铜合金电线

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense. All products listed herein have been qualified under the requirements for the product as specified in the latest adopted issue of the applicable non-Government standard. This list is subject to change without notice; revision or amendment of this list will be issued as necessary. The listing of a product does not release the manufacturer from compliance with the non-Government standard requirements.

WIRE, ELECTRICAL, CROSSLINKED POLYALKENE, CROSSLINKED ALKANE-IMIDE POLYMER, OR POLYARLYENE INSULATED, COPPER OR COPPER ALLOY [Superseded: NAVY QPL-81044 -17 CANC NOTICE 1, NAVY QPL-81044-17, NAVY QPL-81044-16, NAVY QPL-81044-15, NAVY QPL-81044-14, NAVY

DLA MS90561 REV G-2007 轴向溢放口编织电缆夹

Dimensions are in inches, unless otherwise specified, tolerance is ± .010 (.25 mm).

GRIP, CABLE, WOVEN, STRAIN RELIEF, AXIAL

DLA A-A-59725 A-2007 高电流 自动电缆保护器 一半要求

This commercial item description (CID) covers the general requirements for high current, automotive cable protectors. Protectors covered by this CID are intended for commercial/industrialapplications.

PROTECTOR, AUTOMOTIVE CABLE, HIGH CURRENT, GENERAL REQUIREMENTS FOR

DLA QPL-28830-13-2007 波纹外导体半刚性无线射频同轴电缆一般规格

The activity responsible for this QPL is the Defense Supply Center Columbus (DSCC-VQ), Columbus, OH 43218-3990.

CABLE, RADIO FREQUENCY, COAXIAL, SEMIRIGID, CORRUGATED OUTER CONDUCTOR, GENERAL SPECIFICATION FOR

JB/T 10696.5-2007 电线电缆机械和理化性能试验方法 第5部分:腐蚀扩展试验

JB/T 10696的本部分规定了腐蚀扩展试验的试验设备、试样制备、试验程序和试验结果的评定。 本部分适用于试验电缆铝套上高聚物防蚀外套覆盖的紧密程度，以及当此防蚀外套受局部损坏后，铝套的腐蚀是否局限于规定的区域。 本部分应与JB/T 10696.1一起使用。

Test methods for determining mechanical, physical and chemical properties of electric cables and wires Part 5: Corrosion spread test

JB/T 10696.8-2007 电线电缆机械和理化性能试验方法 第8部分:氧化诱导期试验

JB/T 10696的本部分规定了氧化诱导期的试验设备、试样制备、试验程序和试验结果及计算。 本部分是通过测定试祥在高温氧气条件下，开始发生自动催化氧化反应的时间，来判断试样的热稳定性能，适用于电线电缆用聚烯烃绝缘和护套材料，同时适用于通信电缆用填充膏。 本部分应与JB/T 10696.1一起使用。

Test methods for determining mechanical, physical and chemical properties of electric cables and wires Part 8: Test for oxidative inductive time

JB/T 10696.7-2007 电线电缆机械和理化性能试验方法 第7部分:抗撕试验

JB/T 10696的本部分规定了抗撕试验的试验设备、试样制备、试验程序和试验结果及计算。 本部分适用于测定重型橡套软电缆及矿用橡套软电缆的橡皮护套抗撕裂性能。 本部分应与JB/T 10696.1一起使用。

Test methods for determining mechanical, physical and chemical properties of electric cables and wires Part 7: Tear test

JB/T 10696.6-2007 电线电缆机械和理化性能试验方法 第6部分:挤出外套刮磨试验

JB/T 10696的本部分规定了挤出外套刮磨试验的试验设备、试样制备、试验程序和试验结果的评定。 本部分适用于试验电缆外径30Mmm及以上的塑料外套的耐刮磨性能。 本部分应与JB/T 10696.1一起使用。

Test methods for determining mechanical, physical and chemical properties of electric cables and wires Part 6: Test for abrasion of oversheaths

JB/T 10696.4-2007 电线电缆机械和理化性能试验方法 第4部分:外护层环烷酸铜含量试验

JB/T 10696的本部分规定了外护层环烷酸铜含量试验的试验设备、试样制备、试验程序和试验结果及计算。 本部分适用于测定电缆外护层上采用环烷酸铜防腐剂预浸渍的天然纤维材料中所含环烷酸铜的含量。 本部分应与JB/T 10696.1一起使用。

Test methods for determining mechanical, physical and chemical properties of electric cables and wires Part 4: Test for copper naphthenate content of protective coverings

JB/T 10696.3-2007 电线电缆机械和理化性能试验方法 第3部分：弯曲试验

JB/T 10696的本部分规定了弯曲试验的试验设备、试样制备、试验程序和试验结果的评定。 本部分适用于固定敷设用电缆的弯曲试验。 本部分应与JB/T 10696.1一起使用。

Test methods for determining mechanical, physical and chemical properties of electric cables and wires Part 3: Bending test