29.130.01 开关装置和控制器综合 标准查询与下载

T/CES 021-2018 气体绝缘金属封闭开关设备机械振动检测技术规范

目前，气体绝缘金属封闭开关设备（以下简称GIS）设备装备量较大，一个变电站的设备规模也越来越大，往往有十几或二十几个间隔，母线长达一两百米，这样在设备运行过程中很容易产生机械振动。振动产生的原因有很多种，如支撑件设置不合理、部件松动、合闸不到位等。因此，有必要在现场对运行GIS设备进行振动信号检测，发现各类缺陷，及时处理，避免重大事故的发生。 为规范GIS设备机械振动检测原理、检测系统及检测方法，制定本标准。 本标准规定了GIS设备机械振动检测原理、检测系统及检测分析方法等内容。 本标准适用于额定电压为126kV~1100kV的气体绝缘金属封闭开关设备机械振动检测。

Technical specifications of mechanical vibration detection for gas-insulated metal-enclosure switchgear

T/CES 010-2018 统一潮流控制器工程系统试验规范

统一潮流控制器（UPFC）技术的推广应用为解决电网潮流灵活控制的难题提供了有效手段。开展UPFC工程系统试验，全面考核UPFC主设备及系统的功能和性能，对于保证工程可靠投运及安全稳定运行至关重要。目前，国内外均没有UPFC工程系统试验相关的技术标准规范可供参考，迫切需要相应的UPFC试验标准来规范UPFC工程系统试验的项目和方法，提高调试完整性和正确性，保证UPFC安全可靠运行。 为了规范UPFC工程系统试验的项目、方法、要求及验收标准，满足UPFC系统试验和验收需要，并为设备制造、工程设计、系统运行和维护提供参考，特制定本标准。

System testing standard for UPFC project

T/XDB 010-2017 电能表外置断路器技术规范

GB/T 1804         一般公差未注公差的线性和角度尺寸的公差 GB/T 10963.1-2005 电气附件家用及类似场所用过电流保护断路器第1部分：用于交流的断路器 GB/T 17626.2-2006 电磁兼容试验和测量技术静电放电抗扰度试验 GB/T 17626.4-2008 电磁兼容试验和测量技术电快速瞬变脉冲群抗扰度试验 GB/T 17626.5-2008 电磁兼容 试验和测量技术 浪涌（冲击）抗扰度试验 GB/T 19334-2003 低压开关设备和控制设备的尺寸在成套开关设备和控制设备中作电器机械支承的标准安装轨 GB/T 20645-2006 特殊环境条件高原用低压电器技术要求 GB/T 21706-2008 模数化终端组合电器 GB/T 26572-2011 电子电气产品中限用物质的限量要求 Q/GDW 11421-2015 电能表外置断路器技术规范 Q/GDW 11008-2013 低压计量箱技术规范 CQC 1121-2016    电能表外置断路器技术规范 中国南方电网    费控电能表用外置低压断路器技术规范(2016年4月版)

Technical specifications of external circuit breaker for electric energy meter

CSA C22.2 No.178.3-2017(R2022) 转换开关设备 超过 1000 伏

1.1 These requirements cover automatic, non-automatic, and manual transfer switches, operating at voltages of greater than 1000 Vac, and intended for use in non-hazardous locations in accordance with Annex B, Item 1, the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1, Part 1, to provide for power as follows: a) Automatic transfer switches for use in emergency systems in: 1) Emergency systems in accordance with the Standard for Emergency Electrical Power Supply for Buildings, CSA C282-15; 2) Health care facilities in accordance with Rule 24-304 of the Canadian Electrical Code (CEC) Part I; 3) Articles 517, Health Care Facilities, and 700, Emergency Systems, of the National Electrical Code, ANSI/NFPA 70 (refer to Annex B, Item 1); and 4) The Health Care Facilities Code, ANSI/NFPA 99, (refer to Annex B, Item 12). Note: Transfer switches for optional standby systems are not recognized in Canada. b) Transfer switches for use in optional standby systems in accordance with Article 702 of the National Electrical Code, ANSI/NFPA 70 (refer to Annex B, Item 1). Note: Automatic transfer switches for optional standby systems are not recognized in Canada. c) In legally required standby systems in accordance with Article 701 of the National Electrical Code, ANSI/NFPA 70(refer to Annex B, Item 1). Note: Legally-required standby systems are not recognized in Canada. d) Automatic transfer switches for use in accordance with the Standard for the Installation of Stationary Pumps for Fire Protection, ANSI/NFPA 20 or the Standard for Fire Pump Controllers, CSA C22.2 No. 263, (refer to Annex B, Item 2). 1.2 These requirements cover transfer switches rated greater than 1000 V to 46 kV. 1.3 These requirements cover transfer switches together with their associated control devices including, but not limited to, voltage sensing relays, frequency sensing relays, and time delay relays. 1.4 An automatic transfer switch as covered by these requirements is a device that automatically transfers a common load from a normal supply to an alternate supply in the event of failure of the normal supply, and automatically returns the load to the normal supply when the normal supply is restored. An automatic transfer switch can be provided with a logic control circuit that inhibits automatic operation of the device from either a normal to an alternate supply, or from an alternate to a normal supply when the switch reverts to automatic operation upon loss of power to the load. 1.5 A non-automatic transfer switch as covered by these requirements is a device, operated manually by a physical action, or electrically by a remote control, for transferring a common load between a normal and alternate supply. 1.6 These requirements only cover completely enclosed transfer switches.

Transfer switch equipment, over 1000 Volts

EN 61800-9-1:2017 可调速电力驱动系统 第 9-1 部分：电力驱动系统、电机启动器、电力电子设备及其驱动应用的生态设计 为使用电力驱动设备设置能效标准的一般要求

IEC 61800-9-1:2017 specifies the general methodology to energy efficiency standardization for any extended product by using the guidance of the extended product approach (EPA). This document specifies the methodology of determination of losses of the extended product and its sub-parts. It is applicable to motor systems operated by a motor starter or by a converter (power drive systems).

Adjustable speed electrical power drive systems - Part 9-1: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - General requirements for setting energy efficiency standards for power driven equipment using

EN 61800-9-2:2017 可调速电力驱动系统 第 9-2 部分：电力驱动系统 电机启动器 电力电子及其驱动应用的生态设计 电力驱动系统和电机启动器的能效指标

Adjustable speed electrical power drive systems - Part 9-2: Ecodesign for power drive systems@ motor starters@ power electronics and their driven applications - Energy efficiency indicators for power drive systems and motor starters

NB/T 42058-2015 智能电网用户端系统通用技术要求

本标准适用于交流不超过1000V，直流不超过1500V的电气系统及设备。本标准规定了智能电网用户端各系统(包括电能管理系统、智能配电系统、分布式发电系统、电动汽车充放电控制系统、分布式储能系统等)的主要技术要求和功能，以及相关应用系统集成、信息交互应遵循的主要技术原则。本标准适用于智能电网用户端整体及各子系统的总体规划、方案设计、系统集成和运行维护。

General requirements for smart grid user side system

CAN/CSA-C22.2 No.60730-2-5-2014(R2019) 家用和类似用途自动电气控制装置 第2-5部分：自动电气燃烧器控制系统的特殊要求（符合 ANSI Z21.20-2014 和 UL 60730-2-5 的双国标准）

1 Scope and normative references This clause of part 1 is applicable except as follows: 1.1 Replacement: This part of IEC 60730 applies to automatic electrical burner control systems for the automatic control of burners for oil, gas, coal or other combustibles for household and similar use including heating, air conditioning and similar use. This part 2-5 is applicable to a complete burner control system and to a separate programming unit. This part 2-5 is also applicable to a separate electronic high-voltage ignition source and to a separate flame detector. Separate ignition devices (electrodes, pilot burners, etc.) are not covered by this part 2-5 unless they are submitted as part of a burner control system. Requirements for separate ignition transformers are contained in IEC 60989 . 1.1DV.1 D2 Modification of 1.1 by adding the following text to the note: Separate ignition devices (electrodes, pilot burners, etc.) are covered by this part 2-5 (Refer to Annex DVKK). Requirements for separate ignition transformers are covered in Standard for Specialty Transformers, UL 506, and CSA C22.2 No. 13, Standard for Luminous Tube Signs, Oil and Gas Burner Ignition Equipment, Cold-Cathode Interior Lighting. Throughout this part 2-5, where it can be used unambiguously, the word ²system² means ²burner control system² and ²systems² means ²burner control systems². Systems utilizing thermoelectric flame supervision are not covered by this part 2-5. 1.1DV.2 D2 Modification of 1.1 by adding the following text: Devices such as thermoelectric flame supervision, pilot burners, oxygen depletion safety shut-off systems (ODS), thermoelectric safety shut-off devices, fast-acting thermocouples, and other components are covered in Annex DVKK. 1.1.1 This part 2-5 applies to the inherent safety, to the manufacturer's declared operating values, operating times and operating sequences where such are associated with burner safety and to the testing of automatic electrical burner control systems used in, on, or in association with, burners. Requirements for specific operating values, operating times and operating sequences are given in the standards for appliances and equipment. Systems for equipment not intended for normal household use, but which nevertheless may be used by the public, such as equipment intended to be used by laymen in shops, in light industry and on farms, are within the scope of this part 2-5. This part 2-5 applies to systems using NTC or PTC thermistors, additional requirements for which are contained in Annex J. This part 2-5 does not apply to systems designed exclusively for industrial applications. 1.1.1DV D2 Modification of 1.1.1 by adding the following text: This part 2-5 does apply to systems designed exclusively for industrial applications. 1.1.2 This part 2-5 applies to manual controls when such are electrically and/or mechanically integral with automatic controls. Requirements for manual switches not forming part of an automatic control are contained in IEC 61058-1. Throughout this part 2-5, the word ²equipment² means ²appliance and equipment². 1.2 Replacement: This part 2-5 applies to systems with a rated voltage not exceeding 660 V and with a rated current not exceeding 63 A. 1.2DV DR Modification of 1.2 by adding the following text: The maximum control output voltage is 600 V. The maximum current is unlimited. The primary input circuit of a system shall be a two-wire, one-side-grounded system, having a voltage rating of not more than a nominal 120 volts. A switch or protective device shall be in the circuit electrically connected to the ungrounded supply conductor. 1.3 Replacement: This part 2-5 does not take into account the response value of an automatic action of a control, if such a response value is dependent upon the method of mounting the control in the equipment. Where a response value is of significant purpose for the protection of the user, or surroundings, the value defined in the appropriate household equipment standard or as determined by the manufacturer applies. This part 2-5 includes systems responsive to flame properties. 1.4 Replacement: This part 2-5 applies also to systems incorporating electronic devices, requirements for which are contained in Annex H.

Automatic electrical controls for household and similar use - Part 2-5: Particular requirements for automatic electrical burner control systems (Bi-national standard with ANSI Z21.20-2014 and UL 60730-2-5)

CAN/CSA-C22.2 No.60730-2-5-2014(C2019) 家用和类似用途自动电气控制装置 第2-5部分：燃烧器自动电气控制系统的特殊要求（ANSI Z21.20-2014 和 UL 60730-2-5 两国标准）

Domaine d'application et références normatives L'article de la partie 1 s'applique avec les exceptions suivantes: 1.1 Remplacement: La présente partie de la CEI 60730 s'applique aux systèmes de commande électrique automatiques de brûleurs pour la commande automatique de brûleurs pour fioul, gaz, charbon ou autres combustibles à usage domestique et analogue, y compris le chauffage, la climatisation et usages analogues. La présente partie 2-5 est applicable à un système complet et à une unité de programmation séparée. Cette partie 2-5 est également applicable à une source électronique d'allumage haute tension séparée et à un détecteur de flamme séparé. Des dispositifs d'allumage séparés (électrodes, veilleuses de brûleur, etc.) ne sont pas couverts par la présente partie 2-5 à moins d'y être soumis en tant que partie d'un système. Les prescriptions pour les transformateurs séparés d'allumage sont traités dans la CEI 60989. Partout où il est utilisé dans la présente partie 2-5, le terme «système» signifie «système de commande de brûleur» et systèmes» signifie «systèmes de commande de brûleur» quand ils peuvent être utilisés sans ambiguïté. Les systèmes utilisant le contrôle thermoélectrique de flamme ne sont pas couverts par la présente partie 2-5. 1.1.1 La présente partie 2-5 s'applique à la sécurité intrinsèque, aux valeurs de fonctionnement, aux temps de fonctionnement et aux séquences de fonctionnement déclarés par le fabricant, dans la mesure où ils interviennent dans la sécurité du brûleur, ainsi qu'aux essais des systèmes de commande électrique automatiques de brûleurs utilisés dans, sur, ou avec des brûleurs. Les prescriptions relatives aux valeurs de fonctionnement, temps de fonctionnement et séquences de fonctionnement spécifiques sont données dans les normes relatives aux appareils et matériels. Les dispositifs de commande électrique automatiques des matériels non destinés à l'usage domestique normal mais qui peuvent cependant être utilisés par le public, tels que les matériels destinés à être utilisés par des personnes sans qualification particulière dans des magasins, dans l'industrie légère et dans les fermes, relèvent du domaine d'application de la présente partie 2-5. La présente partie 2-5 s'applique aux dispositifs de commande électrique automatiques utilisant des thermistors NTC ou PTC, dont les prescriptions complémentaires sont contenues à l'annexe J. La présente partie 2-5 ne s'applique pas aux systèmes conçus exclusivement pour des applications industrielles. 1.1.2 La présente partie 2-5 s'applique aux dispositifs de commande manuelle dans le cas où ces derniers sont solidaires électriquement et/ou mécaniquement des dispositifs de commande automatiques. Les prescriptions relatives aux interrupteurs manuels ne faisant pas partie d'un dispositif de commande automatique sont contenues dans la CEI 61058-1. Partout où il est utilisé dans la présente partie 2-5, le terme «matériel» signifie «matériel et appareil». 1.2 Remplacement: La présente partie 2-5 s'applique aux systèmes dont la tension nominale ne dépasse pas 660 V et dont le courant nominal ne dépasse pas 63 A. 1.3 Remplacement: La présente partie 2-5 ne prend pas en considération la valeur de réponse d'une action automatique d'un dispositif de commande lorsqu'elle est influencée par la méthode de montage du dispositif de commande dans le matériel. Dans les cas où une telle valeur de réponse est importante du point de vue de la protection de l'utilisateur ou de l'environnement, la valeur spécifiée dans la norme particulière du matériel domestique appropriée ou prescrite par le fabricant s'applique. Les dispositifs de commande sensibles aux propriétés des flammes sont inclus dans la présente partie 2-5. 1.4 Remplacement: La présente partie 2-5 s'applique aussi aux dispositifs de commande incorporant des dispositifs électroniques dont les prescriptions sont contenues à l'annexe H.

Automatic electrical control devices for domestic and similar use - Part 2-5: Particular requirements for automatic electrical control systems for burners (bi-national standard with ANSI Z21.20-2014 and UL 60730-2-5)

JB/T 9613-2013 船用低压开关设备和控制设备型号编制方法

本标准规定了船用低压开关设备和控制设备型号的编制方法。本标准适用于电压为交流1 000 V及以下或直流1 500 V及以下的船用低压开关设备和控制设备。

Compilation of type for low-voltage switchgear and controlgear assemblies in ships

IEEE Std C37.59/COR-2011 电源开关装置和设备的转换用要求;勘误

Errata to Requirements for Conversion of Power Switchgear Equipment

ANSI/IEEE 1613a:2011 安装于电力变电站的通讯网络设备的标准环境和测试要求.修改件:增加一个定义,直流电源要求(5.1)和附件E.历史记录

This document specifies standard service conditions, standard ratings, environmental performance requirements,and testing requirements for communications networking devices and communications ports in protective relays installed in electric power substations. It does not cover such equipment designed for operation in other environments, such as office locations.

Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Electric Power Substations Amendment: Adding of One Definition, DC Power Supply Requirements (5.1), and Annex E- History

UL 347-2009 中压交流接触器控制器和控制中心

Medium-voltage AC contactors, controllers, and control centers

JIS C 8480 AMD 1:2009 低压配电用盒式开关装置附件(修改件1)

Box-type switchgear assemblies for low-voltage distribution purpose (Amendment 1)

ANSI/IEEE 1613:2009 安装在电力变电站的通信网络设备用环境标准及测试要求

This document specifies standard service conditions, standard ratings, environmental performance requirements, and testing requirements for communications networking devices and communications ports in protective relays installed in electric power substations.

Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Electric Power Substations

DS/CLC/TR 61800-6:2007 可调速电力驱动系统 第6部分：确定负载类型和相应额定电流的指南

This technical report provides alternative methods for specifying ratings for adjustable speed electrical power drive systems (PDS) and in particular their basic drive modules (BDM).It is not intended to cover adjustable speed drives for traction purposes. General rules for rating specification for low voltage adjustable speed d.c. power drive systems are contained in 61800-1, and for low voltage adjustable frequency a.c. power drive systems in 61800-2.

Adjustable speed electrical power drive systems - Part 6: Guide for determination of types of load duty and corresponding current ratings

SANS 61117:2006 部分类型测试组件(PTTA)的短路承受力评估方法

Describes an extrapolation method for assessing the short-circuit withstand strength of partially type-tested assemblies(PTTA)

A method for assessing the short-circuit withstand strength of partially type-tested assemblies (PTTA)

ANSI/IEEE C37.66:2005 交流电系统(1 to 38 kV)用电容器开关的标准要求

Required definitions, ratings, and procedures for performing design tests, production tests, and construction requirements for Capacitor Switches for Alternating-Current Systems from 1000 V to 38 kV.

Standard Requirements for Capacitor Switches for Alternating-Current Systems (1 to 38 kV)

LST EN 50152-3-1-2004 铁路应用 固定装置 交流开关设备的特殊要求 第 3-1 部分：牵引系统中特定用途的测量、控制和保护装置 申请指南

Railway applications. Fixed installations. Particular requirements for a.c. switchgear. Part 3-1: Measurement, control and protection devices for specific use in a.c. traction systems. Application guide

IEEE Std C37.24-2003 太阳辐射对室外金属外壳的开关设备的影响的评定指南

Intended to assist in evaluating the effect of solar radiation on outdoor metal-enclosed switchgear and is applicable to outdoor metal-enclosed power switchgear, control switchboards and metal-enclosed bus.

Guide for evaluating the effect of solar radiation on outdoor metal-enclosed switchgear