29.130.20 低压开关装置和控制器 标准查询与下载

GOST IEC 61095-2015 家用和类似用途的机电式接触器

Electromechanical contactors for household and similar purposes

GOST IEC 61439-4-2015 低压开关设备和控制设备组合装置. 第4部分. 建筑工地用成套设备的特殊要求

Low-voltage switchgear and controlgear assemblies. Part 4. Particular requirements for assemblies for construction sites

GOST IEC 60947-7-4-2015 低压开关设备和控制设备. 第7-4部分. 辅助设备. 铜导体的PCB接线端子

Low-voltage switchgear and controlgear. Part 7-4. Ancillary equipment. PCB terminal blocks for copper conductors

GOST IEC 61439-3-2015 低压开关设备和控制设备组合装置. 第3部分. 拟由普通人操作用的配电板

Low-voltage switchgear and controlgear assemblies. Part 3. Distribution boards intended to be operated by ordinary persons

GSO IEC 60947-8:2014 低压切割、连接和控制设备 第8部分：旋转电机的内部集成热保护控制器 (PTC)

This part of IEC 60947 specifies rules for control units, which perform the switching functions in response to the thermal detectors incorporated in rotating electrical machines according to IEC 60034-11, and the industrial application. It specifies rules for that type of system comprising a positive temperature coefficient (PTC) thermistor detector having particular characteristics, and its associated control unit. The PT100 detectors are covered by IEC 60751, where the resistor values are given according to the temperatures of the detector. The present rules lay down the characteristics of association of this particular positive temperature coefficient thermistor detector and its associated control unit (designated “Mark A detector” and “Mark A control unit”), when they are used in thermal protection systems. NOTE It is not possible to specify all the requirements for the operating characteristics of a control unit, as they are dependent on some aspects of the thermal detectors. Some aspects of the requirements of the thermal protector system can only be specified when account is taken of the characteristics of the rotating machine to be protected and the method of installation of the detector within the machine. For these reasons, for each characteristic it is necessary to specify who is responsible for stating the required values and who is responsible for compliance with the requirement and for carrying out any confirmatory test.

Low-voltage switchgear and controlgear - Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines

GSO IEC/TR 60890:2014 一种低压开关设备和控制设备温升计算验证方法

This Technical Report specifies a method of temperature-rise verification of low-voltage switchgear and controlgear ASSEMBLIES by calculation. The method is applicable to enclosed ASSEMBLIES or partitioned sections of ASSEMBLIES without forced ventilation. It is not applicable where temperature rise verification to the relevant product standard of the IEC 61439 series has been established NOTE 1 The influence of the materials and wall thicknesses usually used for enclosures can have some effect on the steady state temperatures. However, the generalised approach used in this technical report ensures it is applicable to enclosures made of sheet steel, sheet aluminium, cast iron, insulating material and the like. The proposed method is intended to determine the temperature rise of the air inside the enclosure. NOTE 2 The air temperature within the enclosure is equal to the ambient air temperature outside the enclosure plus the temperature rise of the air inside the enclosure caused by the power losses of the installed equipment. Unless otherwise specified, the ambient air temperature outside the ASSEMBLY is the air temperature indicated for the installation (average value over 24 h) of 35 °C. If the ambient air temperature outside the ASSEMBLY at the place of use exceeds 35 °C, this higher temperature is deemed to be the ambient air temperature.

A method of temperature-rise verification of low-voltage switchgear and controlgear assemblies by calculation

GSO IEC 62026-3:2014 低压开关设备和控制设备 控制器设备接口 (CDI) 第3部分：DeviceNet

This part of IEC 62026 specifies an interface system between single or multiple controllers, and control circuit devices or switching elements. The interface system uses two conductor pairs within one cable – one of these pairs provides a differential communication medium and the other pair provides power to the devices. This part establishes requirements for the interoperability of components with such interfaces. This part of IEC 62026 specifies the following particular requirements for DeviceNet: − requirements for interfaces between controllers and switching elements; − normal service conditions for devices; − constructional and performance requirements; − tests to verify conformance to requirements. These particular requirements apply in addition to the general requirements of IEC 62026-1.

Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 3: DeviceNet

GSO IEC 61915-2:2014 低压分离和控制设备 联网工业设备的设备形式 第2部分：起动器和类似设备的基本设备形式

This part of IEC 61915 specifies root device profiles as defined by IEC 61915-1 for starters and similar equipment covered by the following product standards: – electromechanical contactors and motor-starters (IEC 60947-4-1), – AC semiconductor motor controllers and starters (IEC 60947-4-2), – AC semiconductor controllers and contactors for non-motor loads (IEC 60947-4-3), – control and protective switching devices (or equipment) (CPS) (IEC 60947-6-2), – control units for built-in thermal protection (PTC) for rotating electrical machines (IEC 60947-8).

Low-voltage switchgear and controlgear - Device profiles for networked industrial devices - Part 2: Root device profiles for starters and similar equipment

GSO IEC/TR 61641:2014 封闭式低压切割、连接和控制设备组件内部故障电弧条件下的试验手册

This technical report gives guidance on the method of testing of ASSEMBLIES under conditions of arcing in air due to an internal fault. The purpose of this test is to assess the ability of the ASSEMBLY to limit the risk of personal injury, damage of ASSEMBLIES and its suitability for further service as a result of an internal arcing fault. The test procedure given in this technical report applies only: – to enclosed, floor-standing or wall-mounted low-voltage switchgear and controlgear assemblies according to IEC 61439-2 (power switchgear and controlgear assemblies – PSC ASSEMBLIES); NOTE This technical report can be used as a reference for arc fault tests of other products, but adaptations of the test procedures and acceptance criteria can apply taking into account the specifics of such other ASSEMBLIES or products. – to situations when doors and covers of the ASSEMBLY are closed and correctly secured. When tests under different or more severe conditions are agreed between the user and the manufacturer, this technical report can be used as a guide. The test procedure given in this technical report takes into consideration: – the effects of the internal overpressure acting on covers, doors, etc.; – the thermal effects of the arc or its roots on the enclosures and of ejected hot gases and glowing particles. The test procedure given in this technical report does not cover: – other effects which can constitute a risk, such as toxic gases and loud noises; – conditions during maintenance work, open doors or similar; – access to the top and bottom of the ASSEMBLY. This is a voluntary test made at the discretion of the manufacturer.

Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault

GSO IEC 61915-1:2014 低压开关设备和控制设备 联网工业设备的设备配置文件 第1部分：设备配置文件开发的一般规则

The IEC 61915 series is intended to improve interoperability of devices, network tools and application software. This part of IEC 61915 defines a framework for common representation of networked industrial devices and provides a template for documenting such a representation, independent of the network used. This framework follows the principles given in IEC/TR 62390, the “Common automation device – Profile guideline”, and refers to ISO 15745, “Industrial automation systems and integration – Open systems application integration framework”. NOTE 1 The device profile format specified in this part of IEC 61915 is compatible with devices connected to both bit- and byte-oriented networks. This part of IEC 61915 applies to root device profiles, generic device profiles, and specific device profiles. The root device profiles will be published in subsequent parts of the IEC 61915 series. NOTE 2 This International Standard is specifically intended for products covered by the IEC 60947 series. NOTE 3 Organisations such as consortia are encouraged to use the rules defined in this part of IEC 61915 to develop generic device profiles for use within their own organisations. Users (product manufacturers and other organizations) should use the root device profiles together with the rules defined in this part of IEC 61915. This part of IEC 61915 allows users to make extensions to the root device profiles and/or generic device profiles. Where no suitable root device profile exists, the user may develop generic or specific device profiles using the rules defined in this part of IEC 61915. This part of IEC 61915 recommends the use of a profile exchange language for representation of the device profile information in order to facilitate the profile’s use by network tools and application software. NOTE 4 The types of devices may vary from simple devices, such as pilot lights, push-buttons and limit switches, to more complex devices with many bytes of information, such as motor controllers, semiconductor motor starters, etc.

Low-voltage switchgear and controlgear - Device profiles for networked industrial devices - Part 1: General rules for the development of device profiles

GSO IEC 60715:2014 低压切断、连接和控制装置的尺寸 标准安装在导轨上 为切割、连接和控制设备安装中的电气设备提供机械支撑

This standard specifies dimensional and functional requirements for the compatible mounting of varied electrical devices on some types of rails in switchgear and controlgear assemblies. Appendices deal with specific steel mounting rails satisfying the requirements of this standard, and give additional dimensional data and loading requirements applicable to such rails.

Dimensions of low-voltage switchgear and controlgear. Standardized mounting on rails for mechanical support of electrical devices in switchgear and controlgear installations

GSO IEC 62026-2:2014 低压开关设备和控制设备 控制器设备接口 (CDI) 第2部分：执行器传感器接口 (AS-i)

This part of IEC 62026 specifies a method for communication between a single control device and switching elements, and establishes a system for the interoperability of components with the specified communication interfaces. The complete system is called “Actuator Sensor interface (AS-i)”. This standard describes a method for connecting switching elements, such as low-voltage switchgear and controlgear, standardized within IEC 60947, and controlling devices. The method may also be applied for connecting other devices and elements. Where inputs and outputs I/O are described in this standard, their meaning is regarding the master, the meaning regarding the application is the opposite.

Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i)

KS C IEC 60947-2:2014 低压开关柜和控制装置 第2部分：断路器

Low-voltage switchgear and controlgear — Part 2: Circuit-breakers

DIN EN 61439-1 Bb.1 Berichtigung 1:2014 低压开关设备和控制设备组件. 第1部分: 总则; 补充件1: 指定装配用指南 (IEC/TR 61439-0-2013), DIN EN 61439-1 附页1 (VDE 0660-600-1 附页1)-2014-06勘误表

Low-voltage switchgear and controlgear assemblies - Part 1: General rules; Supplement 1: Guidance to specifying assemblies (IEC/TR 61439-0:2013), Corrigendum to DIN EN 61439-1 Beiblatt 1 (VDE 0660-600-1 Beiblatt 1):2014-06

DIN EN 62026-7:2014 低压开关设备和控制设备组件. 控制器设备接口 (CDI). 第7部分: CompoNet (IEC 62026-7-2010, 修订版); 德文版本EN 62026-7-2013

Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 7: CompoNet (IEC 62026-7:2010, modified); German version EN 62026-7:2013

DIN EN 60947-5-3:2014 低压开关装置和控制器.第5-3部分:控制电路设备和开关元件.故障状态下确定运行状况的设备接近性用要求.(PDDB) (IEC 60947-5-3-2013).德文版本EN 60947-5-3-2013

Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB) (IEC 60947-5-3:2013); German version EN 60947-5-3:2013

DIN EN 62626-1:2014 低压开关设备和控制设备的封闭式设备. 第1部分: 修理和维护工作期间提供隔离的IEC 60947-3范围之外的封闭式隔离开关 (IEC 62626-1-2014); 德文版本EN 62626-1-2014

Low-voltage switchgear and controlgear enclosed equipment - Part 1: Enclosed switch-disconnectors outside the scope of IEC 60947-3 to provide isolation during repair and maintenance work (IEC 62626-1:2014); German version EN 62626-1:2014

BS 6423:2014 低压开关设备和控制设备维护的实施规程

This British Standard gives recommendations and guidance for the maintenance of low-voltage switchgear and controlgear having a rated voltage up to and including 1 000 V a.c. or 1 500 V d.c. This standard is applicable to stationary and movable switchgear and controlgear with or without an enclosure. It is also applicable to switchgear and controlgear for use under special service conditions,possibly with additional recommendations,for example in ships and rail vehicles. This standard also gives recommendations on safety precautions for personnel carrying out maintenance. Guidance on the levels of maintenance necessary for and also procedures for the maintenance of the principal components within equipment is included. Guidance is also given on the assessment of the on-going suitability of equipment.

Code of practice for maintenance of low-voltage switchgear and controlgear

KS C IEC 60947-5-9-2014(2019) 低压开关柜和控制装置 - 第5-9部分:控制电路设备和开关元件 - 流量开关

Low-voltage switchgear and controlgear — Part 5-9: Control circuit devices and switching elements — Flow rate switches

KS C IEC 60947-7-1-2014(2019) 低压开关柜和控制装置 - 第7-1部分:辅助设备 - 铜导体接线端子

Low-voltage switchgear and controlgear — Part 7-1: Ancillary equipment — Terminal blocks for copper conductors