29.140 电灯及有关装置 标准查询与下载

DB37/T 3568.4-2019 绿色照明LED灯具 第4部分：LED工矿灯

Green Lighting LED Luminaires Part 4: LED High Bay Lights

DB37/T 3568.6-2019 绿色照明LED灯具 第6部分：LED植物生长灯

Green Lighting LED Luminaires Part 6: LED Grow Lights

DB37/T 3569-2019 绿色照明LED灯具能效限定值及能效等级

Allowable values of energy efficiency and energy efficiency grades for green lighting LED lamps

GA 883-2018 公安单警装备 强光手电

Public security single police equipment strong light flashlight

EN 62838:2016/AC:2017-11 用于一般照明服务的 LEDsi 灯，电源电压不超过 50 V acrms 或 120 V 无纹波直流 安全规范

IEC 62977-3-9:2023 specifies standard measurement conditions and methods for determining the sparkle contrast of direct-view displays which comprise display matrix elements to render real 2D images on a flat panel and an anti-glare layer. This document excludes measurement of sparkle, which is intentionally obtained by the specular reflection from reflecting flakes in coatings and paints.

LEDsi lamps for general lighting services with supply voltages not exceeding 50 V a.c. r.m.s. or 120 V ripple free d.c. - Safety specifications

CAN/CSA-C22.2 No.250.13-2017 用于照明应用的发光二极管 (LED) 器件

1.1 Les spécifications de cette norme s’appliquent aux appareillages à diodes électroluminescentes (DEL) formant partie intégrante d’un luminaire ou d’un autre appareil d’éclairage, et qui fonctionne dans le spectre visible entre 400 et 700 nm. Ces spécifications couvrent également les composants des appareillages à DEL, comprenant appareillages d’alimentation pour DEL, contrôleurs, barrettes, modules, et boîtiers, selon les définitions de cette norme. 1.2 Ces produits d’éclairage sont destinés à l’installation sur des circuits de dérivation d’une tension nominale de 600 V ou moins, conformément au Code canadien de l’électricité, Première partie, et pour raccordement à des sources d’énergie isolées (non raccordées au réseau de distribution public) comme les génératrices, batteries d’accumulateurs, piles à combustible, piles solaires, et autres. 1.3 1.3.1 Les appareillages à DEL sont employés dans les produits d’éclairage conformes aux normes de produits finis énumérés dans cet article. Les spécifications de cette norme ont pour objet de compléter celles des autres normes sur les produits finis. 1.3.2 Les luminaires à DEL sont conformes aux normes sur les produits finis suivants : a) CSA C22.2 nº207; b) CSA C22.2 nº12; c) CSA C22.2 nº89; d) CSA C22.2 nº141; e) CSA C22.2 nº166; f) CSA C22.2 nº9; g) CSA C22.2 nº250.0; h) CSA C22.2 nº256; i) CSA C22.2 nº250.7; j) CSA C22.2 nº1993; k) CSA TIL B-31B; et l) CSA TIL B-39. 1.3.3 Les appareillages d’alimentation pour DEL sont conformes aux normes de produits finis ci-après : a) CAN/CSA-C22.2 nº223; et b) CAN/CSA-C22.2 nº60950-1. 1.4 Dans cette norme, le terme «doit» indique une exigence, c’est-à-dire une prescription que l’utilisateur doit respecter pour assurer la conformité à la norme; «devrait» indique une recommandation ou ce qu’il est conseillé mais non obligatoire de faire; et «peut» indique une possibilité ou ce qu’il est permis de faire. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes sont qualifiées de normatives (obligatoires) ou d’informatives (facultatives) pour en préciser l’application. 1.5 Les valeurs sont exprimées en unités SI aux fins de cette norme. Les valeurs entre parenthèses sont données à titre d’information et aux fins de comparaison seulement.

Light-emitting diode (LED) devices for lighting applications

QB/T 5039-2017 LED灯具性能测试方法

LED lamp performance test method

DB35/T 1617-2016 室内照明用LED 吸顶灯具技术规范

本规范规定了室内照明用LED吸顶灯具（以下简称“吸顶灯具”）的术语和定义、分类、技术要求、试验方法、检验规则以及标志、包装、运输、贮存的要求。 本规范适用于以LED为光源、电源电压不超过交流250V的室内照明用LED吸顶灯具，不包括平板灯具。

Technical specifications for LED ceiling lamps for indoor lighting

SN/T 3326.9-2016 进出口照明器具检验技术要求 第9部分：太阳能光伏照明装置

Technical Requirements for Inspection of Import and Export Lighting Appliances Part 9: Solar Photovoltaic Lighting Devices

EN 62838:2016 电源电压不超过 50 V acrms 或 120 V 无纹波直流的一般照明服务用 LEDsi 灯 安全规范

LEDsi lamps for general lighting services with supply voltages not exceeding 50 V a.c. r.m.s. or 120 V ripple free d.c. - Safety specifications

QB/T 4847-2015 LED平板灯具

本标准规定了LED平板灯具的术语和定义、分类、一般要求、一般试验要求、电性能、光输出、LED灯具寿命，色坐标、相关色温和显色性，空间色品不一致性、距高比、亮度限制、亮度均匀度、结构要求、标记、验证。 本标准适用于电源电压不超过250 V的LED平板灯具。

LED flat panel luminaires

IEC 62838:2015 适用于供电电压不超过50伏的普通照明用LEDi灯均方根或120伏无纹波直流电 - 安全规格

"This International Standard specifies the safety and interchangeability requirements@ together with the test methods and conditions@ required to show compliance of LED lamps with integrated means for stable operation@ intended for domestic and similar general lighting purposes@ having: ?C a rated power up to 60 W ?C a rated voltage equal to or less than 50 V a.c. r.m.s. or equal or less 120 V ripple free d.c.@ ?C caps according to Table 1. NOTE 1 The value of 60 W rated power is under consideration. Heat management may require lower power. This standard shall be used for products in conjunction with ELV lighting installations. With reference to IEC 60364-7-715@ in ELV lighting installations only SELV sources are applied. Where bare conductors are used@ the maximum lamp voltage shall be 25 V a.c. or 60 V d.c. The requirements of this standard relate only to type testing. For lamps > 25 V a.c. or 60 V d.c.@ recommendations for whole production testing or batch testing are given in IEC 60598-1 Table Q.1@ column class III luminaire@ column 4 or 5. NOTE 2 Where in this standard the term ""lamp(s)"" is used@ it is understood to stand for semi-integrated LED lamp(s) with supply voltages as in the scope above@ except where it is obviously assigned to other types of lamps. An overview of systems composed of LED modules@ lamps and controlgear is given in IEC 62504. Supply voltage does not mean necessarily mains voltage@ e.g. 230 V / 50 Hz. A semi-integrated LED lamp can also be driven on a supply voltage with 12 V a.c. or d.c. The control unit in the controlgear in a semi-integrated LED lamp then provides the conversion of 12 V a.c. or d.c. to a special current and voltage to power the LED inside the semi-integrated LED lamp. Schematically@ the types of LEDni and LEDsi lamps are shown in Figure 1."

LEDsi lamps for general lighting services with supply voltages not exceeding 50 V a.c. r.m.s. or 120 V ripple free d.c. - Safety specifications

EN 62471-5:2015 灯和灯系统的光生物安全性 第5部分：图像投影仪

Photobiological safety of lamps and lamp systems - Part 5: Image projectors

GSO IEC/TR 62732:2015 用于指定显色性和相关色温的三位代码

This Technical Report describes how to construct a three-digit code, representing a shorthand string combining the nominal general colour rendering index and the nominal correlated colour temperature. NOTE The code is established in industry and commerce.

Three-digit code for designation of colour rendering and correlated colour temperature

GSO IEC 62471:2015 灯和灯系统的光生物安全

This International Standard gives guidance for evaluating the photobiological safety of lamps and lamp systems including luminaires. Specifically it specifies the exposure limits, reference measurement technique and classification scheme for the evaluation and control of photobiological hazards from all electrically powered incoherent broadband sources of optical radiation, including LEDs but excluding lasers, in the wavelength range from 200 nm through 3000 nm.

Photobiological safety of lamps and lamp systems

GSO IEC 62386-102:2015 用于照明控制的可寻址数字接口 第102部分：一般要求 控制设备

This Part of IEC 62386 is applicable to control gear in a bus system for control by digital signals of electronic lighting equipment. This electronic lighting equipment should be in line with the requirments of IEC 61347, with the addition of d.c. supplies. NOTE Tests in this standard are type tests. Requirements for testing individual control gear during production are not included.

Digital addressable lighting interface - Part 102: General requirements - Control gear

GSO IEC/TR 62750:2015 荧光灯调光的统一标准计算

This Technical Report applies to fluorescent lamp dimming systems. It deals with the interface of fluorescent lamps and dimming electronic controlgear. A unified framework for standardization of fluorescent lamp dimming systems and the associated parameter calculation method are described in this Technical Report. Dimming of fluorescent lamps is becoming increasingly important as a strategy for conserving global energy resources. This report is the result of many years of effort by global experts to understand and test fluorescent dimming systems with the objective of standardizing these systems to grow confidence and reliability in the marketplace. Two theoretical frameworks have been merged to create this unified dimming standardization method: the SoS (sum of squares of lead-in-wire currents) and CV (cathode voltage) models. The application of dimming to actual fluorescent lamp and electronic controlgear (ECG) systems is the primary concern for reliability in the application and end-user confidence. Characteristics of the dimming parameter limits described in this report and observed in real system applications such as in situ field diagnostics are offered as informative. The practical need to use substitution resistors for ECG qualification is described in this report and also given as normative parameters in the lamp and ECG standards. No attempt to treat the informative real lamp-ECG system parameters as normative will be made in either the lamp or the controlgear standards.

Unified fluorescent lamp dimming standard calculations

DB44/T 1620-2015 地铁场所用LED照明设计标准

本标准规定了地铁场所用LED照明的照明方式、照明质量、节能评价等。 本标准适用于广东省新建、改建和扩建的地铁场所用LED照明（地铁车辆照明除外）设计。

LED lighting design standards for subway places

DB44/T 1622-2015 地铁场所照明用LED灯应用技术规范

本技术规范规定了地铁场所照明用LED灯的技术要求、试验方法，其中包括产品的规格分类、环境适应性要求、安全和电磁兼容性要求、光电性能要求等。 本技术规范适用于地铁场照明用LED灯。 本技术规范不适用于车辆照明产品和信号指示类照明产品。 注：在本标准中出现的“灯”即代表“地铁场所照明用LED灯”，除非有特别指明灯的类型。

Application technical specification for LED lamps for lighting in subway places

DB44/T 1621-2015 非自镇流LED管形灯

本标准规定了室内一般照明用非自镇流LED管形灯的术语和定义、分类、尺寸规格、一般要求、试验方法、检验规则、标志、产品使用说明书、包装、运输和贮存的要求。 适用范围如下： ——额定功率不大于60 W，额定电流不大于5 A； ——仅由安全特低电压（SELV）电源供电，且额定电压小于或等于60 V直流值； ——灯头符合表1要求。 注：在本标准中出现的“灯”代表“非自镇流LED管形灯”，除非有特别指明是其他类型的灯。

Non-self-ballasted LED tube lamps