43.180 检查、维修和试验设备 标准查询与下载

SAE J2254-1995 流体动力管道清洗工艺

The procedures and guidelines detailed in this SAE information Report provide various techniques and processes to properly clean fluid power piping prior to assembly and operation. There are two recommended processes, pickling and flushing. Each procedure will remove particulate contaminates if properly applied.

Fluid Power Piping Cleaning Process

SAE J2264-1995 采用减退技术的道路负荷底盘测功机模拟

This procedure covers two-wheel drive vehicle operation and single-axle electric dynamometer load coefficient adjustment to simulate track road load within the speed range of track testing and the dynamometer inertia and road load simulation capabilities. The purpose is to provide a uniform procedure for adjusting an electric chassis roll dynamometer to provide accurate simulation of the resistance which must be overcome by the vehicle powertrain to maintain steady speed on a flat road, as determined by track coastdown tests on that vehicle.

Chassis Dynamometer Simulation of Road Load Using Coastdown Techniques

AS/NZS 2538:1995 汽车支架

Specifies requirements for the design, construction, performance and labelling of vehicle support stands.

Vehicle support stands

JIS D 8101:1994 汽车用便携式液压千斤顶

この規格は，自動車に用いる油圧式携行ジャッキ(以下，ジャッキという。)について規定する。

Portable hydraulic jacks for automobiles

JIS D 8102:1994 汽车用液压千斤顶

この規格は，自動車に用いる移動装置をもっ油圧式ガレージジャッキ(以下，ジャッキという。)について規定する。

Hydraulic garage jacks for automobiles

JIS D 8103:1994 汽车用便携式螺旋千斤顶

この規格は，自動車に用いるねじ式携行ジャッキ(以下，ジャッキという。)について規定する。

Portable screw jacks for automobiles

AS/NZS 2640:1994 汽车用可移动式楔块

Specifies safety and performance requirements for portable ramps used in the maintenance and display of motor vehicles. Design requirements and testing methods are included covering strength, structural integrity, roll-off and ease of mounting (drive on test).

Portable ramps for vehicles

ISO 9141-2:1994 道路车辆 诊断系统 第2部分:交换数字信息的 CARB 要求

Is limited to vehicles with nominal 12 V supply voltage. Describes a subset of ISO 9141:1989. Specifies the requirements for setting-up the interchange of digital information between on-board emission-related electronic control units of road vehicles and the SAE OBD II scan tool as specified in SAE J1978. This communication is established to facilitate compliance with California Code of Regulation, Title 13, 1968.1.

Road vehicles; diagnostic systems; part 2: CARB requirements for interchange of digital information

AS/NZS 2693:1993 汽车千斤顶

Specifies design and performance requirements for jacks, other than trolley jacks, which are intended for use with cars, trucks, trailers and other road vehicles. Covers jacks supplied with new vehicles as well as those supplied as accessories or replace

Vehicle jacks

ANSI/SAE J726-1993 空气滤清器试验规程

Air Cleaner Test Code

ISO 11530:1993 道路车辆 液压千斤顶 规范

Specifies design and safety requirements, and test methods under normal operation conditions and modified operating conditions for hydraulic jacks, used for changing wheels and putting on chains.

Road vehicles; hydraulic jacks; specifications

SAE J600-1993 前照灯对光试验机

This SAE Recommended Practice provides laboratory test procedures for testing headlamp aim test machines to determine their ability to aim or to check the aim of headlamps, fog lamps, and auxiliary driving and lower beam lamps. This report does not apply to aiming devices of the kind covered by SAE J602.

Headlamp Aim Testing Machines

ISO 10604:1993 道路车辆 前照灯光束定位测量设备

Specifies the dimensional, mechanical and optical quality criteria for equipment to measure or to verify the orientation of the luminous beams emitted by the headlamps installed on road motor vehicles excluding mopeds and motorcycles. The equipment also allows evaluation of the quality of the luminous beams by visual means. Lays down the requirements for the floor on which the vehicles are placed, the vehicle preparation, equipment using a distant screen, optical equipment with installation and operating instructions, photometric devices.

Road vehicles; measurement equipment for orientation of headlamp luminous beams

DIN ISO 9141:1992 道路车辆.诊断系统.数字信息互换要求

This standard specifies the requirements for setting up the interchange of digital information between on-board electronic control units (ECUs) of road vehicles and suitable diagnostic testers. This communication is established in oder to facilitate inspection, test diagnosis and adjustment of vehicles, systems and ECUs. This standard does not apply when system-specific diagnostic test equipment is used.

Road vehicle; diagnostic systems; requirements for interchange of digital information; identical with ISO 9141:1989

ISO 8720:1991 乘用车 机械式千斤顶规范

Specifies requirements to ensure the safety in use of original equipment mechanical jacks supplied with passenger cars (as defined in ISO 3833) in changing wheels and putting on chains.

Passengers cars; specifications for mechanical jacks

YB 4056-1991 金属板材矫正机工作辊技术条件

Specifications for working rolls of sheet metal leveling machines

ISO 9141:1989 道路车辆 诊断系统 对数字信息交换的要求

Specifies the requirements for setting up the interchange of digital information between on-board Electronic Control Units (ECUs) of road vehicles and suitable diagnostic testers. This communication is established in order to facilitate inspection, test diagnosis and adjustment of vehicles, systems and ECUs. Does not apply when system-specific diagnostic test equipment is used.

Road vehicles - Diagnostic systems - Requirements for interchange of digital information

ISO/TR 9790-1:1989 道路车辆.拟人侧面碰撞假人.第1部分:评估假人生物逼真度的侧面头部碰撞响应要求

Road vehicles — Anthropomorphic side impact dummy — Part 1: Lateral head impact response requirements to assess biofidelity of dummy

GOST 4.112-1989 停车场装置.指标名称

Настоящий стандарт распространяется на гаражное оборудование и устанавливает номенклатуру показателей для включения их в технические з

Product-quality index system. Garage equipment. Nomenclature of indices

DVS 2510-1988 商用车辆的补焊；范围和一般原则

Repair welding of commercial vehicles; scope and general principles