45.080 钢轨和线路构件 标准查询与下载

TB/T 2344-2012 43 kg/m~75 kg/m钢轨订货技术条件

本标准规定了43 kg/m~75 kg/m钢轨的术语和定义、订货所需信息、型式尺寸及极限偏差、技术要求、试验方法、检验规则、标志和质量证明书、质量保证等内容。 本标准适用于最高运行速度为160 km/h铁路用43 kg/m~75 kg/m热轧和在线热处理钢轨。高速铁路用热处理钢轨可参照执行。

Technical specifications for the procurement of 43 kg/m~75 kg/m rails

DS/EN 13231-3:2012 铁路应用 轨道 工程验收 第3部分：轨道改造钢轨的验收

This European Standard specifies the technical requirements and the measurements to be made for the acceptance of work to reprofile longitudinally and/or transversely the heads of railway rails. For acceptance purposes, two classes of longitudinal profile and three classes of transverse profile tolerance are defined.Annexes describe procedures to verify reference instruments to be used for these measurements as well as methods to approve non-reference instruments to be used for measurements.This European Standard applies to reprofiled vignole railway rails 46 kg/m and above.It does not apply for acoustic rail reprofiling.A form of acceptance documentation t

Railway applications - Track - Acceptance of works - Part 3: Acceptance of reprofiling rails in track

DS/EN 13848-4:2012 铁路应用 轨道 轨道几何质量 第4部分：测量系统 手动和轻型设备

This part of this European Standard specifies the minimum requirements that shall be met by measuring systems fitted on track geometry measuring trolleys and manually operated devices to give an evaluation of track geometry quality when using one or more of the parameters described in EN 13848-1. It sets out the acceptable differences from EN 13848-1 when using track geometry measuring trolleys and manually operated devices to measure track geometry.It applies to all track geometry measuring systems fitted to track geometry measuring trolleys and manually operated devices after the date of implementation of this standard.

Railway applications - Track - Track geometry quality - Part 4: Measuring systems - Manual and lightweight devices

JIS E 1102 AMD 2:2012 铁路轨道用鱼尾板(修改件2)

Fish plates for rails (Amendment 2)

JIS E 1126 AMD 1:2012 膨胀节(修改件1)

Expansion joints (Amendment 1)

JIS E 1101 AMD 2:2012 未处理钢制道岔和交叉用平底铁轨和特殊轨道(修改件2)

Flat bottom railway rails and special rails for switches and crossings of non-treated steel (Amendment 2)

JIS E 1202 AMD 1:2012 预应力混凝土轨枕.后拉伸型(修改件1)

Prestressed concrete sleepers -- Post-tensioning type (Amendment 1)

JIS E 1122 AMD 1:2012 过渡钢轨(修改件1)

Compromise rails (Amendment 1)

JIS E 1110 AMD 1:2012 碳钢垫板(修改件1)

Carbon steel tie-plates (Amendment 1)

JIS E 1125 AMD 1:2012 胶接绝缘钢轨(修改件1)

Glued insulated rails (Amendment 1)

JIS E 1201 AMD 1:2012 预应力混凝土轨枕.预拉伸型(修改件1)

Prestressed concrete sleepers -- Pretensioning type (Amendment 1)

JIS E 1117 AMD 1:2012 减震用弹性轨道垫板(修改件1)

Resilient sleeper pads for shock-absorbing (Amendment 1)

JIS E 1118 AMD 1:2012 预应力混凝土轨枕.铁轨紧固件(修改件1)

Prestressed concrete sleepers -- Rail fastenings (Amendment 1)

DS/EN 13232-6+A1:2012 铁路应用 轨道 道岔和交叉路口 第6部分：固定的普通交叉路口和钝角交叉路口

The scope of this European Standard is to:- establish a working terminology for fixed crossings and their constituent parts, and identify the main types;- specify the different and varying ways by which crossings can be described using the following parameters:- geometry of the crossing;- types of construction;- design criteria;- manufacturing processes;- tolerances and inspection.

Railway applications - Track - Switches and crossings - Part 6: Fixed common and obtuse crossings

DS/EN 13232-7+A1:2012 铁路应用 轨道 道岔和交叉路口 第7部分：带有可移动部件的交叉路口

The scope of this part is:- to establish a working terminology for crossings with moveable parts, which means crossings with moveable parts to close the gap of the running edge, and their constituent parts, and identify the main types;- to list the minimum informative requirements for the manufacture of crossings with moveable parts and/or their constituent parts;- to formulate codes of practice for inspection and tolerances for crossings with moveable parts and/or their constituent parts;- to establish the limits and extent of supply;- to list the method by which crossings with moveable parts and their constructional parts should be identified and traced;-

Railway applications - Track - Switches and crossings - Part 7: Crossings with moveable parts

GOST R 54747-2011 铁路用1520 mm轨距铁路钢筋混凝土枕木.通用规范

Ferro-concrete cross ties for railways for 1520 mm gauge railways. General specifications

GOST R 55184-2012 铁路机车车辆用液压式夹轨器. 通用规范

Hydraulic clampers for railway rolling stock. General specifications

DS/EN 13232-5+A1:2011 铁路应用 轨道 道岔和道口 第5部分：道岔

The scope of this European Standard is:- establish a working definition for switches and their constituent parts and identify the main types;- specify the minimum requirements for the manufacture of the switches and/or constituent parts;- specify codes of practice for inspection and tolerances of both full and half sets of switches and their constituent parts;- establish the limits and scope of supply;- list the methods by which switches and their parts should be identified and traced;- list the different and varying ways by which switches can be described using the following parameters:- geometry of the switches;- types of construction;- performance requir

Railway applications - Track - Switches and crossings - Part 5: Switches

DS/EN 13232-9+A1:2011 铁路应用 轨道 道岔和交叉路口 第9部分：布局

The scope of this part is:- to describe the design process of switches and crossings, and the use of the other parts of this standard;- to define the main criteria to be taken into account during the design of the layout, including the safety and functional dimensions as well as geometrical and material aspects;- to define the main criteria to be verified during the design approval;- to define the geometrical and non-geometrical acceptance criteria for inspection of layouts assembled both in the fabrication plant and at track site in case of layouts that are delivered non or partially assembled or in a """"kit"""" form;- to determine the limits of supply;-

Railway applications - Track - Switches and crossings - Part 9: Layouts

DS/EN 13232-2+A1:2011 铁路应用 轨道 道岔和道口 第2部分：几何设计要求

This part of this European Standard covers the following subjects:- geometric design principles for wheel guidance;- definition of basic limits of supply;- applied forces and their adequate support;- tolerance levels.These are illustrated herein by application to a turnout. The main switch and crossing components are represented in turnouts and the principles used in turnouts apply equally to more complex layouts.

Railway applications - Track - Switches and crossings - Part 2: Requirements for geometric design