共找到 1675 条与 小型船 相关的标准,共 112 页
This document specifies requirements for through-hull fittings, seacocks, hose connections, their fittings and their installation in small craft with a length of hull, LH, as defined in ISO 8666:2020, of up to 24 m. This document is not applicable to engine and heater exhaust fittings, and sail drive through-hull fittings.
Small craft — Seacocks and through-hull fittings
This document specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol or petrol blended with ethanol, and diesel fuel or diesel fuel blended with FAME, designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm, and 0,25 MPa for hoses up to 63 mm inner diameter in small craft. . It applies to hoses for small craft with permanently installed fuel systems. Specifications for fire-resistant hoses are given in ISO 7840:2021. Specifications for permanently installed fuel systems are given in ISO 10088:2013.
Small craft — Non-fire-resistant fuel hoses
This document establishes a coding system to achieve identification of any small craft in terms of: a) identification code of the country of the manufacturer of the craft; b) identification code of the manufacturer; c) serial number; d) month and year of manufacture; e) model year. This document is applicable to small craft of all types and materials, of hull length, LH, up to 24 m.
Small craft — Craft identification — Coding system
This document specifies requirements for electrically operated bilge pumps intended for use in removing bilge water. It applies to: — direct current (DC) bilge pumps which operate at a nominal voltage not exceeding 50 V; and — single phase alternating current (AC) bilge pumps which operate at a nominal voltage not exceeding 250 V. It does not cover pumps intended for damage control.
Small craft — Electrically operated bilge pumps
BS ISO 23625 Small craft -Lithium-ion batteries
本文件规定了瑞安传统龙舟的分类及最大载荷、基本要求、技术要求、试验方法、检验规则、运输和贮存。
Ruian traditional dragon boat
Small craft. Electrical systems. Alternating and direct current installations
BS EN ISO 8846 Small craft - Electrical devices - Protection against ignition of surrounding flammable gases
Small craft. Automatic watertight ventilation shutdown system
BS EN ISO 10239 Small craft. Liquefied petroleum gas (LPG) systems
Small craft — Electrical systems used for electrical propulsion
Small craft — Power measurements and declarations — Part 2: Electric marine propulsion
This document specifies the items included in the maximum load of small craft, without exceeding the limits set by other ISO standards for stability, freeboard, and flotation. It further sets requirements for seating and occupancy areas of crew members. Personal watercraft are excluded from the Scope of this document.
Small craft — Maximum load capacity
This document establishes definitions of main dimensions and related data and of mass specifications and loading conditions. It applies to small craft having a length of the hull (LH) of up to 24 m.
Small craft — Principal data
This document specifies requirements for pumping or alternative means designed to remove normal accumulations of bilge water for small craft with a length of hull, LH, as defined in ISO 8666:2016, of up to 24 m. This document does not set requirements for bilge pumps or bilge-pumping systems designed for damage control.
Small craft — Bilge-pumping systems
This document specifies technical requirements and test methods for windows, portlights, hatches, deadlights and doors on small craft with a length of hull, LH, as defined in ISO 8666:2016, of up to 24 m. It takes into account the type of craft, its design category, and the location of the appliance. The appliances considered in this document are only those that are critical for the craft's watertightness. Openings and non-opening devices fitted below area I (see 3.5.2) are excluded from the scope of this document.
Small craft — Windows, portlights, hatches, deadlights and doors — Strength and watertightness requirements
This document specifies requirements for the uniform display of the information exhibited on the builder’s plate of small craft. Personal watercraft are excluded from the Scope of this document.
Small craft — Builder's plate
This document specifies requirements for the design, construction and installation of sewage treatment systems on small craft. It does not address waste retention systems, nor accidental discharge prevention of pollutants (e.g. oil, fuel) overboard. It does not address the technical discharge limits of a sewage treatment unit, subject to certain international as well as national regulations.
Small craft — Waste systems — Part 2: Sewage treatment systems
ISO 8099-1:2018 specifies requirements for the design, construction and installation of systems for temporary retention of sewage for subsequent disposal. It applies to small craft with a length of hull (LH) of up to 24 m. ISO 8099-1:2018 does not address waste water treatment systems.
Small craft — Waste systems — Part 1: Waste water retention
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号