共找到 1671 条与 小型船 相关的标准,共 112 页
BS ISO 23625 Small craft -Lithium-ion batteries
本文件规定了瑞安传统龙舟的分类及最大载荷、基本要求、技术要求、试验方法、检验规则、运输和贮存。
Ruian traditional dragon boat
Small craft. Electrical systems. Alternating and direct current installations
BS EN ISO 8846 Small craft - Electrical devices - Protection against ignition of surrounding flammable gases
Small craft. Automatic watertight ventilation shutdown system
BS EN ISO 10239 Small craft. Liquefied petroleum gas (LPG) systems
Small craft — Electrical systems used for electrical propulsion
Small craft — Power measurements and declarations — Part 2: Electric marine propulsion
This document specifies the items included in the maximum load of small craft, without exceeding the limits set by other ISO standards for stability, freeboard, and flotation. It further sets requirements for seating and occupancy areas of crew members. Personal watercraft are excluded from the Scope of this document.
Small craft — Maximum load capacity
This document establishes definitions of main dimensions and related data and of mass specifications and loading conditions. It applies to small craft having a length of the hull (LH) of up to 24 m.
Small craft — Principal data
This document specifies requirements for pumping or alternative means designed to remove normal accumulations of bilge water for small craft with a length of hull, LH, as defined in ISO 8666:2016, of up to 24 m. This document does not set requirements for bilge pumps or bilge-pumping systems designed for damage control.
Small craft — Bilge-pumping systems
This document specifies technical requirements and test methods for windows, portlights, hatches, deadlights and doors on small craft with a length of hull, LH, as defined in ISO 8666:2016, of up to 24 m. It takes into account the type of craft, its design category, and the location of the appliance. The appliances considered in this document are only those that are critical for the craft's watertightness. Openings and non-opening devices fitted below area I (see 3.5.2) are excluded from the scope of this document.
Small craft — Windows, portlights, hatches, deadlights and doors — Strength and watertightness requirements
This document specifies requirements for the uniform display of the information exhibited on the builder’s plate of small craft. Personal watercraft are excluded from the Scope of this document.
Small craft — Builder's plate
This document specifies requirements for the design, construction and installation of sewage treatment systems on small craft. It does not address waste retention systems, nor accidental discharge prevention of pollutants (e.g. oil, fuel) overboard. It does not address the technical discharge limits of a sewage treatment unit, subject to certain international as well as national regulations.
Small craft — Waste systems — Part 2: Sewage treatment systems
ISO 8099-1:2018 specifies requirements for the design, construction and installation of systems for temporary retention of sewage for subsequent disposal. It applies to small craft with a length of hull (LH) of up to 24 m. ISO 8099-1:2018 does not address waste water treatment systems.
Small craft — Waste systems — Part 1: Waste water retention
This document specifies the requirements for the design, installation and testing of engine-mounted and craft-mounted remote hydraulic steering systems used with single and multiple engine installations of outboard engines over 15 kW per engine, as well as with single and multiple engines of inboard, sterndrive, and water jet drives, all used on small craft. This document does not address emergency means of steering the craft.
Small craft — Remote hydraulic steering systems
This document specifies design and testing requirements for steering wheels for small craft.
Small craft — Steering wheels
This document specifies the requirements for the design, installation and testing of cable over pulley steering systems on small craft with or without a propulsion engine(s), and on small craft with outboard engine(s) up to and including 37 kW total power. It specifies the requirements for the design and testing of all components of a cable over pulley steering system, from the steering mechanism to the mechanical interface with the rudder shaft or the outboard engine. It applies to cable over pulley steering systems, whether for pedestal or bulkhead types. This document does not address emergency means of steering the craft.
Small craft — Steering gear — Cable over pulley systems
This document specifies design, construction, installation and test requirements for remote mechanical cable steering systems and the output ram interface point to rudders, jet drives, outboard and sterndrive engines for small craft. It is applicable to three distinct classes of steering systems for use on various types of craft: — standard duty steering systems, for small craft with single and twin installations of outboard engines with a total over 15 kW power, and with rudders, sterndrives and water-jet drives; — light duty steering systems, for small craft with a single outboard engine of 15 kW to 40 kW power; — mini-jet steering systems, excluding personal watercraft. NOTE Standard and light duty steering systems are mechanically interchangeable. A standard duty steering system can be used on a craft designed for a light duty system. However, a light duty steering system cannot be used on a craft that requires a standard duty steering system. Mini-jet steering systems are mechanically differentiated from the previously mentioned systems and can only be used on mini-jet craft as defined in this document. This document does not address emergency means for steering the craft.
Small craft — Remote mechanical steering systems
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号