49.020 航空器和航天器综合 标准查询与下载

GB/T 15025-1994 飞机飞行模拟机等级要求

本标准规定了飞机飞行模拟机的等级要求和鉴定测试。 本标准适用于民用飞机的飞行模拟机，不适用于旋翼机的模拟机。

Airplane flight simulator standards

GB 15024-1994 飞机飞行模拟机鉴定程序

本标准规定了飞机飞行模拟机的鉴定程序。 本标准适用于民用飞机的飞行模拟机，不适用于旋翼机的模拟机。

Airplane flight simulator qualification procedures

GB 15026-1994 飞机飞行训练器鉴定程序

本标准规定了飞机飞行训练器的鉴定程序。 本标准适用于民用飞机的飞行训练器，不适用于旋翼机的训练器。

Airplane flight training devlice qualification procedures

GB/T 15027-1994 飞机飞行训练器等级要求

本标准规定了飞机飞行训练器的等级要求和鉴定测试。 本标准适用于民用飞机的飞行训练器，不适用于旋翼机的训练器。

Airplane flight training devlice qualification standards

GB 14648-1993 民用航空器飞行事故等级

本标准规定了民用航空器在运行过程中，发生飞行事故的等级划分准则和分类指标，是确定飞行事故严重程度的依据。 本标准适用于在中华人民共和国领域内，从事民用航空活动的所有航空器以及在中华人民共和国登记、在领域外从事民用航空活动的所有航空器。 本标准不适用于首次获得适航证之前的所有民用航空器的试飞活动。

Classification standard for flying accidents of aircraft

GB/T 14410.2-1993 飞行力学概念、量和符号 力、力矩及其系数和导数

本标准规定了描述飞机运动的力、力矩及其系数和导数的术语和符号。 本标准适用于具有固定翼的航空器，其他飞行器可参照使用。

Flight mechanics. Concepts, quantities and symbols Forces, moments, their coefficients and derivatives

GB/T 14410.1-1993 飞行力学概念、量和符号 坐标轴系和运动状态变量

本标准规定了描述飞机运动的坐标轴系和基本运动状态变量的术语和符号。 本标准适用于具有固定翼的航空器，其他飞行器可参照使用。 在本标准中将飞机视为刚体。

Flight mechanics. Concepts, quantities and symbols Axis systems and motion state variables

GB/T 14410.7-1993 飞行力学概念、量和符号 飞行点和飞行包线

本标准规定了飞行力学研究中使用的、用以确定飞机飞行状态的术语和符号。 本标准适用于具有固定翼的航空器，其他飞行器可参照使用。

Flight mechanics. Concepts, quantities and symbols Flight points and flight envelopes

GB/T 14410.6-1993 飞行力学概念、量和符号 飞机几何形状

本标准规定了与飞行力学有关的、用以描述飞机几何形状的最基本的术语和符号。 本标准适用于具有固定翼的陆基航空器，其他飞行器可参照使用。

Flight mechanics. Concepts, quantities and symbols Aircraft geometry

GB/T 14410.5-1993 飞行力学概念、量和符号 飞行测量

本标准规定了在飞行测量中使用的术语和符号。 本标准适用于具有固定翼的航空器，其他飞行器可参照使用。

Flight mechanics. Concepts, quantities and symbols Flight measurements

GB/T 14410.4-1993 飞行力学概念、量和符号 飞行性能

本标准规定了描述飞机飞行性能的术语和符号。 本标准适用于具有固定翼的陆基航空器，其他飞行器可参照使用。

Flight mechanics. Concepts, quantities and symbols Flight performance

GB/T 14410.3-1993 飞行力学概念、量和符号 飞机稳定性和操纵性

本标准规定了研究飞机稳定性和操纵性使用的术语和符号。 本标准适用于具有固定翼的航空器，其他飞行器可参照使用。 本标准中所指的机体坐标轴系的x方向接近飞机的零升力线。

Flight mechanics. Concepts, quantities and symbols Stability and control of aircraft

GB 8563-1988 奖励代码

Code of prize

ASTM F3061/F3061M-24 飞机系统和设备标准规范

Standard Specification for Systems and Equipment in Aircraft

GSO ISO 21384-4:2024 无人机系统 第4部分：词汇

This document defines terms and definitions relating to unmanned aircraft systems that are widely used in science and technology.

Unmanned aircraft systems — Part 4: Vocabulary

GSO ISO 21384-2:2024 无人机系统 第2部分：UAS 组件

This document specifies requirements for ensuring the quality and safety of the design and manufacture of unmanned aircraft systems (UAS) that include unmanned aircraft (UA), remote pilot stations (RPS), datalinks, payloads, and associated support equipment. This document includes information regarding the unmanned aircraft, any associated remote pilot station (RPS)(s), the command and control links (C2 Link), any other required data links (e.g. payload, traffic management information, vehicle identification) and any other system elements as can be required. This document does not cover passenger carrying UAS or technical requirements for the design and manufacturing for UAS components. This document does not include equipment considerations unique to compliance with UA traffic management systems. The document is applicable to the reasonable expected use of a UAS. This document is applicable: a) to UAS designed for use where a State aviation authority has determined a Certificate of Airworthiness (C of A) is not required; b) where a C of A is required, to complement technical standards published by the aviation authority for the purposes of building the certification basis; or c) as an alternative means of compliance if acceptable to the aviation authority.

Unmanned aircraft systems — Part 2: UAS components

ASTM F3180/F3180M-24a 飞机低速飞行特性标准规范

Standard Specification for Low-Speed Flight Characteristics of Aircraft

ASTM F3180/F3180M-24 飞机低速飞行特性标准规范

Standard Specification for Low-Speed Flight Characteristics of Aircraft

ASTM F3309/F3309M-24 小型飞机系统和设备简化安全评估的标准实施规程

1.1  This practice covers methods for conducting a simplified safety assessment of aircraft systems and equipment. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Level 1 and Level 2 Normal Category aeroplanes employing conventional systems. The content may be more broadly applicable. It is the responsibility of the Applicant to substantiate broader applicability as a specific means of compliance. If the criteria specified within this simplified practice is deemed not to be relevant to a particular application, the Applicant should use the safety assessment process defined in Practice F3230 . The topics covered within this practice are: Procedural Flowchart, Failure Condition Identification and Classification, Safety Objectives, Design and Installation Appraisal, Qualitative Analysis of Failure Conditions, Common Mode Analysis, Use of Similarity, and Documentation. 1.2  An applicant intended to propose this information as Means of Compliance for a design approval must seek guidance from their respective oversight authority (for example, published guidance from applicable CAA) concerning the acceptable use and application thereof. For information on which oversight authorities have accepted this standard (in whole or in part) as an acceptable Means of Compliance to their regulatory requirements (hereinafter “the Rules”), refer to the ASTM Committee F44 web page (www.astm.org/COMMITTEE/F44.htm). 1.3  Units— This practice may present information in SI units, English Engineering units, or both; the values stated in each system may not be exact equivalents. Each system shall be used independently of the other; combining values from the two systems may result in nonconformance with the standard. 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Simplified Safety Assessment of Systems and Equipment in Small Aircraft

T/SHUAJQ 0001-2023 民用中大型货运无人机用电机性能检测规范与试验方法

本文件规定了民用中大型货运无人机用电机性能检测规范与试验方法，包括检验检测流程、技术要求和试验方法等内容。 本文件适用于在中国境内使用的民用中大型货运无人机用电机系统部件（最大输出功率在60kW以下）的性能检测和认证等。

Performance testing specifications and test methods for motors used in medium and large civilian cargo unmanned aerial vehicles