49.040 有关航空航天制造用镀涂和有关工艺 标准查询与下载

ASTM F3440-21 飞机维修化学品对低脆锌镍板腐蚀的标准试验方法

1.1 This test method is intended as a means of determining the corrosive effects of aircraft maintenance chemicals on low-embrittling zinc-nickel plating used on aircraft highstrength steel, under conditions of total immersion by quantitative measurements of weight change. Aircraft maintenance chemicals requiring this test method shall be determined by the cognizant engineering authority. 1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6 and 4.1. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Corrosion of Low-Embrittling Zinc-Nickel Plate by Aircraft Maintenance Chemicals

OENORM EN 4868-2021 航天系列 无六价铬底漆的阳极电沉积

Aerospace series - Anodic electrodeposition of hexavalent chromium free primer

21/30436455 DC BS EN 4868 航空航天系列 六价无铬底漆阳极电沉积

BS EN 4868. Aerospace series. Anodic electrodeposition of hexavalent chromium free primer

PN-EN 4689-2021-06 E 航空航天系列 色漆和清漆 双组份室温固化聚氨酯面漆 军用高柔韧性和耐化学试剂

Aerospace series -- Paints and varnishes -- Two-components room temperature curing polyurethane finish -- High flexibility and chemical agent resistance for military application

PN-EN 4688-2021-06 E 航空航天系列 色漆和清漆 耐腐蚀铬酸盐双组份室温固化环氧底漆 军用高耐蚀

Aerospace series -- Paints and varnishes -- Corrosion resistant chromated two-components room temperature curing epoxy primer -- High corrosion resistance for military application

PN-EN 4687-2021-06 E 航空航天系列 色漆和清漆 无铬（非缓蚀）双组份常温固化底漆 军用无铬底漆

Aerospace series -- Paints and varnishes -- Chromate free (non corrosion inhibiting) two-components room temperature curing primer -- Chromate free primer for military application

PN-EN 2133-2021-06 E 航空航天系列 规定抗拉强度≤1 450 MPa的钢、铜、铜合金和镍合金的镀镉

Aerospace series -- Cadmium plating of steels with specified tensile strength ≤ 1 450 MPa, copper, copper alloys and nickel alloys

OENORM EN 4688-2021 航空航天系列 色漆和清漆 耐腐蚀铬酸盐双组份室温固化环氧底漆 军用高耐蚀

Aerospace series - Paints and varnishes - Corrosion resistant chromated two-components room temperature curing epoxy primer - High corrosion resistance for military application

OENORM EN 2133-2021 航空航天系列 规定抗拉强度<=1450MPa的钢、铜、铜合金和镍合金的镀镉

Aerospace series - Cadmium plating of steels with specified tensile strength <= 1450 MPa, copper, copper alloys and nickel alloys

OENORM EN 4687-2021 航空航天系列色漆和清漆无铬酸盐（非腐蚀抑制）双组份室温固化底漆军用无铬酸盐底漆

Aerospace series - Paints and varnishes - Chromate free (non corrosion inhibiting) two-components room temperature curing primer - Chromate free primer for military application

prEN 4868-2021 航天系列 无六价铬底漆的阳极电沉积

Aerospace series - Anodic electrodeposition of hexavalent chromium free primer

BS ISO 8081:2021 航空航天工艺 铝合金化学转化涂层 一般用途

Aerospace process. Chemical conversion coating for aluminium alloys. General purpose

BS ISO 8080:2021 航空航天钛及钛合金的阳极处理 硫酸工艺

Aerospace. Anodic treatment of titanium and titanium alloys. Sulfuric acid process

ISO 8080:2021 航空和航天；钛及钛合金的阳极处理——硫酸法

This document specifies the requirements for producing and testing an unsealed anodic coating on titanium and titanium alloys. The anodic coating is produced by the sulfuric acid process. The coating is used with solid film lubricants for protection of titanium fasteners against galling, for limited protection of less noble metals against galvanic corrosion when in contact with titanium or for other approved uses.

Aerospace — Anodic treatment of titanium and titanium alloys — Sulfuric acid process

ISO 8081:2021 航空航天工艺 - 铝合金化学转化涂层 - 通用

This document specifies the requirements for producing and testing a general purpose chemical conversion coating on aluminium alloys. The chemical conversion coating is used in the manufacture of aerospace products in order to improve paint adhesion and resistance to corrosion. This process can also be used for touch-up of anodic coatings.

Aerospace process — Chemical conversion coating for aluminium alloys — General purpose

ASTM F1864-21 光学和红外透明材料和涂料的防尘蚀性的标准测试方法

1.1 This test method covers the resistance of transparent plastics and coatings used in aerospace windscreens, canopies, and viewports to surface erosion as a result of dust impingement. This test method simulates flight through a defined particle cloud environment by means of independent control of particle size, velocity, impact angle, mass loading, and test duration. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings

SN EN 4688-2021 航空航天系列 色漆和清漆 耐腐蚀铬酸盐双组份室温固化环氧底漆 军用高耐蚀

Aerospace series - Paints and varnishes - Corrosion resistant chromated two-components room temperature curing epoxy primer - High corrosion resistance for military application

SN EN 4689-2021 航空航天系列色漆和清漆双组份室温固化聚氨酯面漆军用高柔韧性和耐化学试剂性

Aerospace series - Paints and varnishes - Two-components room temperature curing polyurethane finish - High flexibility and chemical agent resistance for military application

SN EN 2133-2021 航空航天系列 规定抗拉强度≤1450 MPa的钢、铜、铜合金和镍合金的镀镉

Aerospace series - Cadmium plating of steels with specified tensile strength ≤ 1450 MPa, copper, copper alloys and nickel alloys

SN EN 4687-2021 航空航天系列色漆和清漆无铬酸盐（非腐蚀抑制）双组份室温固化底漆军用无铬酸盐底漆

Aerospace series - Paints and varnishes - Chromate free (non corrosion inhibiting) two-components room temperature curing primer - Chromate free primer for military application