55.040 包装材料和辅助物 标准查询与下载

ASTM D4577-05(2018) 恒定负载下容器抗压性的标准试验方法

Standard Test Method for Compression Resistance of a Container Under Constant Load

ASTM D2063/D2063M-10(2018) 使用非自动（手动）扭矩测试设备测量带连续螺纹封闭件的扭矩保持的标准测试方法

1.1 These test methods evaluate the torque retention of continuous thread closures on containers, with matching finishes, for predetermined environmental conditions over time. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. NOTE 1—The SI unit system is the recommended system. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Measurement of Torque Retention for Packages with Continuous Thread Closures Using Non-Automated (Manual) Torque Testing Equipment

ASTM E1975-18 设备S-280/G电气防护罩标准规范

Standard Specification for Shelter, Electrical, Equipment S-280/G

ASTM F2638-18 使用气溶胶过滤测量多孔包装材料作为代理微生物屏障的性能的标准测试方法

Standard Test Method for Using Aerosol Filtration for Measuring the Performance of Porous Packaging Materials as a Surrogate Microbial Barrier

ASTM F34-13(2018) 柔性阻隔材料液体提取试验细胞结构标准实践

1.1 This practice covers the construction of test cells which may be used for the extraction of components from flexible barrier materials by suitable extracting liquids, including foods and food simulating solvents. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Construction of Test Cell for Liquid Extraction of Flexible Barrier Materials

ASTM D5814-18 使用斑块试验测定回收聚对苯二甲酸乙二醇酯（PET）片和芯片中的污染的标准操作

1.1 This practice covers an indication of the quality of recycled transparent poly(ethylene terephthalate) by examination of a wafer or plaque formed by melting a representative sample and quenching it to prevent crystallization. 1.2 Specific contaminants and impurities such as aluminum particles, dirt particles, paper, and fibers are identified in the transparent wafer. 1.3 The overall color of the plaque is indicative of oxidizable contaminants such as ethylene-vinyl acetate (EVA) glue residue and the number of bubbles present in the plaque gives an indication of the moisture content of the sample. 1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8. NOTE 1—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determination of Contamination in Recycled Poly(Ethylene Terephthalate) (PET) Flakes and Chips Using a Plaque Test

ASTM D7660-10(2018) 对联合国（UN）包装进行内部压力测试的标准指南

Standard Guide for Conducting Internal Pressure Tests on United Nations (UN) Packagings

ASTM D2860/D2860M-18 压敏胶带与纤维板在90°附着力的标准测试方法

1.1 This test method covers the determination of the property of adhesion of pressure-sensitive tape to a fiber-board surface. The user of this test method has the option of choosing the paper surface for the test. The test surface may be the standard linerboard, another linerboard (or paper) of individual interest, or a specific fiberboard. 1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Adhesion of Pressure-Sensitive Tape to Fiberboard at 90° Angle and Constant Stress

ASTM F2825-18 包裹系统用于单包裹递送的气候压力的标准实施规程

1.1 This practice provides a uniform basis for evaluating, in a laboratory, the ability of a packaging system to withstand a range of climatic stresses that a packaging system may be exposed to during distribution throughout the world and still provide the product protection from damage or alteration. 1.2 This practice is designed as conditioning prior to testing for overnight or two-day delivery systems of a single parcel packaging system or as a standalone test for climatic stressing of packaging systems. NOTE 1—Practice F2825 climatic stressing or conditioning is short term in duration. Fiberboard containers are not expected to approach equilibrium moisture content at the climatic conditions used in Practice F2825. Therefore, Practice F2825 conditioning should not be used for distribution environments other than oneto two-day single parcel delivery as it may provide inaccurate or misleading test results for the fiberboard containers. 1.3 This practice does not cover refrigerated, frozen food storage, or cryogenic storage conditions. Only the climatic environments encountered in various regions of the world are covered by this practice. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Climatic Stressing of Packaging Systems for Single Parcel Delivery

ASTM D4504-94(2018) 非危险品工业航运用模制聚乙烯开口头桶的标准规范

1.1 This specification covers molded polyethylene, openhead, self-supporting, nonreusable pails intended for the packaging and transportation of nonhazardous goods. Pails are to have volume capacities between 1 and 7 gal (3.8 to 26.5 L). 1.2 Pails intended to contain hazardous goods (materials) shall be in accordance with and tested to United States Department of Transportation Code of Federal Regulations (CFR) Title 49, Parts (100–199). 1.3 The purpose of this specification is to establish performance requirements and test methods for molded open-head polyethylene pails. 1.4 Additives for the resin used and design of the pails are left to the discretion of the supplier, within the allowable limits of regulatory and performance requirements. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following safety hazards caveat pertains to the test method portions, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Molded Polyethylene Open-Head-Pails for Industrial Shipping of Nonhazardous Goods

ASTM F1884-04(2018) 测定包装材料中残留溶剂的标准试验方法

1.1 This test method covers determination of the amount of residual solvents released from within a packaging material contained in a sealed vial under a given set of time and temperature conditions and is a recommended alternative for Test Method F151. 1.2 This test method covers a procedure for quantitating volatile compounds whose identity has been established and which are retained in packaging materials. 1.3 The analyst should determine the sensitivity and reproducibility of the method by carrying out appropriate studies on the solvents of interest. The analyst is referred to Practice E260 for guidance. 1.4 For purposes of verifying the identity of or identifying unknown volatile compounds the analyst is encouraged to incorporate techniques such as gas chromatography/mass spectroscopy, gas chromatography/infrared spectroscopy or other suitable techniques in conjunction with this test method. 1.5 Sensitivity of this test method in the determination of the concentration of a given retained solvent must be determined on a case by case basis due to the variation in the substrate/solvent interaction between different types of samples. 1.6 This test method does not address the determination of total retained solvents in a packaging material. Techniques such as multiple headspace extraction can be employed to this end. The analyst is referred to the manual supplied with the GC-Autosampling system for guidance. 1.7 The values stated in SI units are to be regarded as the standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Determining Residual Solvents in Packaging Materials

ASTM F3300-18 用往复加权测针测试软包装薄膜耐磨性的标准试验方法

1.1 This test method covers the determination of the abrasion resistance of flexible non-conductive films and packaging materials using a weighted stylus that wears completely through a film by oscillating or reciprocating back and forth along a linear path until an electrical circuit is completed shutting down the test. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Abrasion Resistance of Flexible Packaging Films Using a Reciprocating Weighted Stylus

EN 14932:2018 塑料.包装袋用伸缩热塑性薄膜.要求和试验方法

Plastics - Thermoplastic stretch films for wrapping silage bales

GOST R 58061-2018 改性合成薄膜. 类型和基本参数

Modificated synthetic films. Types and basic parameters

GOST 16295-2018 防腐纸 技术条件

Anticorrosive paper. Specifications

ASTM F2251-13(2018) 柔性包装材料厚度测量的标准测试方法

1.1 This test method covers the measurement of thickness of flexible packaging materials using contact micrometers. 1.2 The Precision and Bias statement for this test method was developed using both handheld and bench top micrometers with foot sizes ranging from 4.8 to 15.9 mm (3⁄16 to 5⁄8 in.). 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thickness Measurement of Flexible Packaging Material

KS T 1018-2017 用于消费容器的微槽波纹纤维板

Microflute corrugated fibreboards for consumer containers

T/NJFW 0009-2017 电子商务包装回收共用服务规范

本标准规定了电子商务包装回收共用服务的术语和定义、 回收网点基本要求、 包装回收要求、 包装共用要求和服务质量控制、 本标准适用于电子商务包装回收、 共用服务的开展

E-commerce packaging recycling shared service specification

KS T 1322-2017 包装用加工纸耐压敏胶粘性测试方法

Testing method for pressure sensitive adhesive resistance of processed papers for packaging

KS T 1067-2017 铝箔复合包装纸

Aluminium foil laminated package paper