55.130 雾化剂罐 标准查询与下载

EN 15007:2017 雾化剂容器-马口铁容器-两件或三件套容器尺寸

This European Standard specifies the dimensions of two and three-piece tinplate aerosol containers with nominal brimful capacities.

Aerosol containers - Tinplate containers - Dimensions of two and three-piece cans

GSO ISO 90-3:2016 轻型金属容器 尺寸和容量的定义和测定 第3部分：气雾罐

This part of ISO 90 defines the diameters, apertures, constructions, shapes and capacities of round, aerosol cans. It specifies methods for determining diameters, gross lidded and brimful capacities. It also gives tolerances on capacity and recommends an international designation. NOTE A list of standards dealing with materials used for aerosol cans is given in the Bibliography.

Light gauge metal containers -- Definitions and determination of dimensions and capacities -- Part 3: Aerosol cans

ASTM D3090-72(2016) 气溶胶产品储存测试标准实践

1.1 This practice covers the storage testing of aerosol products. 1.2 There are two major types of storage tests that may be performed on aerosol products: 1.2.1 Live Storage Tests, where the valves are actuated and the determinations are made at relatively frequent intervals (the purpose being to simulate consumer use of aerosol dispensers), and 1.2.2 Dead Storage Tests, performed to simulate warehouse storage conditions when shelf-life information is sought. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 4.

Standard Practice for Storage Testing of Aerosol Products

ASTM D3091-72(2016) 低压加压产品安全灌装标准实践

1.1 This practice covers the filling of low-pressure pressurized products, either in the laboratory or in production. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 2.

Standard Practice for Safe Filling of Low-Pressure Pressurized Products

GSO ISO 10154:2015 轻型金属容器 三片内颈马口铁罐 顶端尺寸

  Scope is not provided for this standard

Light gauge metal containers -- Three-piece necked-in tinplate aerosol cans -- Dimensions of the top end

BB/T 0006-2014 包装容器 20mm口径铝气雾罐

本标准规定了20mm口径铝气雾罐(以下简称气雾罐)的要求，试验方法，检验规则及其标志、包装、运输、储存。本标准适用于口径为20mm、容量不大于250mL的气雾罐。

Packaging containers.20 mm aperture aluminum monobloc aerosol cans

KS D ISO 90-3:2013 轻型金属容器 定义和尺寸、容量的测定 第3部分：气溶胶罐

Light gauge metal containers－Definitions and determination of dimensions and capacities－Part 3：Aerosol cans

ABNT NBR 14721-2012 气雾罐 - 计算膨胀室的要求

This Standard specifies the requirements for calculation of the expansion chamber in metal packaging for aerosols, using as propellant liquefi ed gases and not liquefi ed gases.

Aerosol canister - Requirements for calculating the expansion chamber

BB/T 0005-2010 气雾剂产品的标示、分类及术语

本标准规定了气雾剂产品的标示要求、分类、术语及其定义。本标准适用于在气雾罐上直接印刷或粘贴的气雾剂产品的标示以及在科研、生产、流通和使用领域的气雾剂产品的分类及术语。

Label, Classification and Terms of Aerosol Products

ANSI/ASABE S572.1-2009 使用滴液光谱进行喷雾嘴分类

Spray Nozzle Classification by Droplet Spectra

ANSI/ASAE S572.1-2009 用滴谱对喷雾嘴分类

Defines droplet spectrum categories for the classification of spray nozzles, relative to specified reference fan nozzles discharging spray into static air or so that no stream of air enhances atomization. The purpose of classification is to provide the nozzle user with droplet size information primarily to indicate off-site spray drift potential and secondarily for application efficacy.

Spray Nozzle Classification by Droplet Spectra

ANSI/UL 147A-2009 不可再填充型(一次性)燃气瓶组件安全标准(提案日期 10/24/08)

Topics include the following: (1) Revision to sample and testing requirements and (2) Clarification of reference to UL 157.

Standard for Safety for Nonrefillable (Disposable) Type Fuel Gas Cylinder Assemblies (Proposals dated 10/24/08)

ANSI/UL 147Aa-2009 非再填充(一次性)型燃料储气瓶组件的安全性标准

Standard for Safety for Nonrefilla ble (Disposable) Type Fuel Gas Cylinder Assemblies

ANSI/UL 147B-2008 不可再充装(一次性)型金属容器组件安全标准

Proposal covers revision to testing requirements.

Standard for Safety for Nonrefillable (Disposable) Type Metal Container Assemblies

DS/EN 14848/AC:2007 气雾剂容器 孔径为 25.4 毫米的金属容器 阀杯的尺寸

This European Standard specifies the critical dimensions of valve cups suitable for clinching into 25,4 mm aperture metal aerosol containers.This standard is intended to be used with the metal aerosol containers specified in EN 14847 and prEN 15006.

Aerosol containers - Metal containers with 25,4 mm aperture - Dimensions of valve cups

LST EN 14848-2006/AC-2007 气雾剂容器 孔径为 25.4 毫米的金属容器 阀杯的尺寸

Aerosol containers - Metal containers with 25,4 mm aperture - Dimensions of valve cups

DIN EN 14848 Berichtigung 1:2007 气溶胶容器.25.4mm孔径的金属容器.阀座尺寸

Aerosol containers - Metal containers with 25,4 mm aperture - Dimensions of valve cups, Corrigenda to DIN EN 14848:2006-02; German version EN 14848:2005/AC:2007

DS/EN 15007:2007 金属气雾剂容器 马口铁容器 两片罐和三片罐的尺寸

This European Standard specifies the dimensions of two and three-piece tinplate aerosol containers with nominal brimful capacities in accordance with European Directive 80/232/EEC [2].

Metal aerosol containers - Tinplate containers - Dimensions of two and three-piece cans

DS/EN 15010:2007 气雾剂容器 铝制容器 与连接件相关的基本尺寸公差

This European Standard defines the critical dimensions of the location of the 25,4 mm aperture relative to the base of aerosol cans for clinching with valve cups.The specification of the fundamental dimensions in this standard, relates to all 25,4 mm aperture aluminium and aluminium alloy cans, irrespective of size, shape and mode of manufacture; whose dimensions and tolerances fall within the dimensional scope of EN 15008.

Aerosol containers - Aluminium containers - Tolerances of the fundamental dimensions in connection with the clinch

DS/EN 15006:2007 金属气溶胶容器 铝制容器 25.4 mm 孔径的尺寸

This European Standard specifies the following dimensions of aluminium metal aerosol cans with 25,4 mmaperture: contact height, outside diameter, inside diameter and shoulder height. It is intended to be used with EN 14848 for clinching with valve cups.

Metal aerosol containers - Aluminium containers - Dimensions of the 25,4 mm aperture