55.130 雾化剂罐 标准查询与下载

ASTM D6535/D6535M-05(2010)e1 测定机械泵分配器汲取管长度的标准试验方法

This test method is to be used to determine the length of a dip tube of a mechanical pump dispenser that extends to the bottom-corner of a container. This test method is to be used to determine the length of a dip tube of a mechanical pump dispenser that extends to the bottom-center of a container.1.1 This test method covers the determination technique for a dip tube of a mechanical pump dispenser. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining the Dip Tube Length of a Mechanical Pump Dispenser

EN 14847:2005 气溶胶容器.马口铁容器.25.4 mm孔径的尺寸

This European Standard specifies the following dimensions of tinplate metal aerosol cans with 25,4 mm aperture:contact height, outside diameter, inside diameter and shoulder height. It is intended to be used with EN 14848 for clinching with valve cups.

Aerosol containers - Tinplate containers - Dimensions of the 25,4 mm aperture

EN 14849:2005 气溶胶容器.玻璃容器.气溶胶阀门金属箍尺寸

This European Standard defines the dimensions which are important for an effective fastening of valves on glass aerosol containers with a nominal diameter of 11 mm, 13 mm, 15 mm, 17 mm, 18 mm and 20 mm neck finish, as defined in EN 14854 .

Aerosol containers - Glass containers - Dimensions of aerosol valve ferrules

ASTM D6633-05(2010) 机械泵分配器的基本功能稳定性的标准试验方法

This test method is used for determining the accelerated usage of a mechanical pump dispenser for consumer usage.1.1 This test method covers the determination of the basic functional stability of a mechanical pump dispenser with a product. 1.2 This test method covers accelerated usage evaluations of mechanical pump dispensers (spray or flow types) with a product. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautions are given in Section 5.

Standard Test Method for Basic Functional Stability of a Mechanical Pump Dispenser

ASTM D4333/D4333M-05(2010)e1 机械泵分配器适应性试验方法

This test method identifies the compatibility of the mechanical pump dispenser components with consumer-type products.1.1 This test method covers testing of the components of mechanical pump dispensers (spray or flow types) for compatibility with products. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for the Compatibility of Mechanical Pump Dispenser Components

ASTM D3890-05(2010) 起动机械泵分配器插程数的标准试验方法

This test method can be used to visually compare priming characteristics of different pump dispensers and different products. This test method is suitable for establishing specifications for both the pump dispenser and the final package.1.1 This test method covers the determination of the number of actuations required to prime a pump dispenser (spray and flow types) with a consumer-type product. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Number of Strokes to Prime a Mechanical Pump Dispenser

EN 14854:2005 气溶胶容器.玻璃容器.瓶颈尺寸

This European Standard specifies the critical dimensions of the neck finish of glass aerosol containers with respecttoThe thorough and tight closing of valves with ferrules defined in EN 14849.This standard is applicable to a nominal diameter of 11 mm, 13 mm, 15 mm, 17 mm, 18 mm and 20 mm neckedaerosol containers with moulded and tubular neck finishes.

Aerosol containers - Glass containers - Dimensions of the neck finish

EN 14850:2005 气溶胶容器.25.4 mm孔径的金属容器.接触高度测量

This European Standard describes a method of measuringThe contact height of the compression closurebetweenThe valve cup andThe aperture of an aerosol container.This standard applies to aerosol containers with 25,4 mm apertures as specified in EN 14847 and prEN 15006fitted with aerosol valve cups as specified in EN 14848.

Aerosol containers - Metal containers with 25,4 mm aperture - Measurement of contact height

EN 14848:2005 气溶胶容器.25.4 mm孔径的金属容器.阀座尺寸.合并勘误表-2007年6月

This European Standard specifies the critical dimensions of valve cups suitable for clinching into 25,4 mm aperturemetal aerosol containers.This standard is intended to be used withThe metal aerosol containers specified in EN 14847 and prEN 15006.

Aerosol containers - Metal containers with 25,4 mm aperture - Dimensions of valve cups

ASTM D4041/D4041M-05(2010)e1 测定人力操纵泵分送器的喷射模式的标准试验方法

This practice can be used to compare spray patterns of different pump dispensers and of different products. Spray patterns from pump dispensers will vary greatly with the design of the actuator and the nature of the liquid. Liquids with differing physical properties will not necessarily yield the same spray pattern when sprayed from the same actuator. Likewise, actuators of different designs will yield spray patterns distinct from each other when the same liquid is used.1.1 This practice covers the determination of spray patterns from pump dispensers. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determining Spray Patterns of Mechanical Pump Dispensers

ASTM D6534-05(2010) 测定机械泵分配器启动力峰值的标准试验方法

1.1 This test method covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 5.

Standard Test Method for Determining the Peak Force-to-Actuate a Mechanical Pump Dispenser

ASTM D4336-05(2010) 机械泵分配器每行程输出功率标准试验方法

This test method can be used to compare the output per stroke of different pump dispensers for the purpose of establishing dosage and use instructions for products of consumer usage. This test method is suitable for establishing specifications for both the pump dispenser and the final package.1.1 These test methods cover the measurement of the mean quantity-by-weight of liquids dispensed from a mechanical pump dispenser (spray or flow type) with a consumer-type product on each actuation. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Determination of the Output Per Stroke of a Mechanical Pump Dispenser

KS D ISO 10154-2004(2014) 轻型金属容器三件套马口铁气雾罐顶端尺寸

Light gauge metal containers－Three-piece necked-in tinplate aerosol cans－Dimensions of the top end

KS D ISO 10154:2004 薄金属容器.三件向内卷曲颈气溶剂罐.顶端尺寸

이 규격은 목(neck)이 있는 3부분으로 구성된 것(three-piece)으로, 주석 도

Light gauge metal containers－Three-piece necked-in tinplate aerosol cans－Dimensions of the top end

KS D ISO 90-3-2004(2009) 轻型金属容器尺寸和容量的定义和测定第3部分:气雾罐

Light gauge metal containers－Definitions and determination of dimensions and capacities－Part 3：Aerosol cans

LST EN ISO 90-3:2002 轻型金属容器 尺寸和容量的定义和测定 第3部分：气雾罐（ISO 90-3:2000）

Light gauge metal containers - Definitions and determination of dimensions and capacities - Part 3: Aerosol cans (ISO 90-3:2000)

DIN 6111:2002 包装.高压包装件.带不可拆卸分配装置的可重复使用的高压包装件

The document applies to pressurised dispensers which are filled with a product and charged with a propellant at the manufacturer's plant. The dispensing valve is clinched to the container and is intended to remain permanently secured to the container.

Packaging - High-pressure packages - Reusable, with non-removable dispensing facility

DS/EN ISO 90-3:2002 轻型金属容器 尺寸和容量的定义和测定 第3部分：气雾罐

This part of the standard defines the diameters, apertures, constructions, shapes and capacities of round, aerosol cans. It specifies methods for determining diameters, gross lidded and brimful capacities. It also gives tolerances on capacity and recommends an international designation.

Light gauge metal containers - Definitions and determination of dimensions and capacities - Part 3: Aerosol cans

ASTM D6633-01 机械泵分配器的基本功能稳定性的标准测试方法

1.1 This test method covers the determination of the basic functional stability of a mechanical pump dispenser with a consumer-type product.1.2 This test method covers accelerated usage evaluations of mechanical pump dispensers (spray or flow types) with a consumer-type product.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautions are given in Section 5.

Standard Test Method for Basic Functional Stability of a Mechanical Pump Dispenser

AS 2278:2000 容量为50 mL-1000 mL（含）的金属气溶胶喷罐

Specifies requirements for materials, construction, filling, performance testing and marking for non-refillable metal dispensers from 50 mL to 1000 mL, maximum net capacity. Each dispenser being pressurized by a liquefied gas propellant, a dissolved prop

Metal aerosol dispensers of capacity 50 mL to 1000 mL inclusive