55.140 粗腰桶、桶、筒等 标准查询与下载

KS T ISO 15750-2-2020 包装 钢桶 第2部分：不可拆卸头（紧头）桶 最小总容量为 212 L、216.5 L 和 230 L

Packaging — Steel drums — Part 2: Non-removable head(tight head)drums with a minimum total capacity of 212 L, 216.5 L and 230 L

KS T ISO 15750-1-2020 包装 钢桶 第1部分：最小总容量为 208 L、210 L 和 216.5 L 的可拆卸头（敞口）桶

Packaging — Steel drums — Part 1: Removable head(open head) drums with a minimum total capacity of 208 L, 210 L and 216.5 L

ASTM F2874-20 标准规范一次性使用便携式应急燃料容器（PEFC）供消费者使用

1.1 This specification establishes nationally recognized construction, performance, and marking standards for portable emergency fuel containers intended for attended transport of fuel and for one time use by consumers. This specification is not for containers intended for unattended storage of fuel. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for One Time Use Portable Emergency Fuel Containers (PEFC) for Use by Consumers

ASTM F3429/F3429M-20 安装在一次性和预填充易燃液体容器中的火焰缓解装置性能的标准规范

1.1 This specification establishes performance requirements for the performance of flame mitigation devices (FMDs) installed in disposable and pre-filled liquid containers, intended for consumer use where the liquid flashpoint is below 60 ºC [140 ºF]. 1.1.1 Uses of disposable and pre-filled flammable liquid containers include but are not limited to fuels, fire starters, and additives for internal combustion engines. 1.1.2 An FMD that complies with this specification minimizes the potential of flame jetting or container rupture from occurring. 1.1.3 Containers without a significant area reduction at the container opening are not covered because there is no hazard of a flame jet or container rupture because an internal pressure rise does not result from an internal ignition. (See Appendix X1.) 1.2 This specification does not apply to the following containers: 1.2.1 Containers greater than 20 L [5.3 gal] or smaller than 100 mL [3.4 oz] in volume. 1.2.2 Containers intended for beverages. 1.2.3 Portable fuel containers as defined in Specification F852/F852M. 1.2.4 One-time use portable emergency fuel containers for use by consumers as defined in Specification F2874. 1.2.5 Containers not intended to be open to ambient conditions such as those for liquefied petroleum gas. 1.3 This specification does not address hazards caused by fire and explosion nor hazards from vapors external to the container when the fuel in the container does not ignite. Further, this specification does not consider scenarios where confinement, obstructions, or preheating cause flame acceleration prior to the flame front reaching the interior of the container. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Information on specific hazards associated with the test methods in this specification is shown in Section 4.4. 1.6 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions. 1.7 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Performance of Flame Mitigation Devices Installed in Disposable and Pre-Filled Flammable Liquid Containers

ASTM F852/F852M-20 消费者用便携式汽油、煤油和柴油容器的标准规范

Standard Specification for Portable Gasoline, Kerosene, and Diesel Containers for Consumer Use

T/ZZB 1366-2019 包装容器 钢质手提油罐

本标准规定了钢质手提油罐（以下简称罐）的结构型式、基本要求、技术要求、检验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于公称容量不超过35 L的盛装汽油、柴油、煤油和润滑油液体的钢质手提油罐。

Packing containers—Steel jerry oil can

KS T 1081-2019 塑料回收容器

Plastic returnable containers

ASTM F852/F852M-19 消费者用便携式汽油、煤油和柴油容器的标准规范

Standard Specification for Portable Gasoline, Kerosene, and Diesel Containers for Consumer Use

CAN/CGSB-43.126-2019 危险品运输用桶的翻新、再制造和修理

1.1 Organization and content This standard specifies the requirements for the reconditioning, remanufacturing and repair of steel and plastic drums for the transportation of dangerous goods. This standard consists of three parts and an annex. Part I specifies the general requirements for drum eligibility, and a registered facility’s quality management system. Part II specifies the requirements for the reconditioning, remanufacturing and repair of steel drums. Part III specifies the requirements for the reconditioning and remanufacturing of plastic drums. Annex A specifies the requirements for the registration of reconditioning, remanufacturing and repair facilities with Transport Canada. 1.2 Application This standard applies to standardized drums (UN/TC/DOT/CTC). 1.3 Additional requirements 1.3.1 Conflict The Transportation of Dangerous Goods Act, 1992 (TDG Act) and the Transportation of Dangerous Goods Regulations (TDG Regulations) may set out additional requirements regarding the design, construction, qualification, selection, use and testing of drums. Where there is an inconsistency between the requirements of this standard and those of the TDG Act or TDG Regulations, the TDG Act or TDG Regulations prevail to the extent of the inconsistency. It is recommended to read the standard in conjunction with the TDG Regulations. 1.3.2 Safety The reconditioning, remanufacturing and repair of a drum in accordance with this standard may require the use of materials and/or equipment that could be hazardous. This standard does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use. 1.3.3 Units Quantities and dimensions used in this standard are given in metric units, mainly SI units.

Reconditioning, remanufacturing and repair of drums for the transportation of dangerous goods

ASTM F3326-19a 便携式燃料容器上火焰缓解装置的标准规范

Standard Specification for Flame Mitigation Devices on Portable Fuel Containers

BS EN ISO 20848-3:2018 包装 塑料桶 适用于标称容量为 113.6l 至 220l 的塑料桶的塞塞封闭系统

What is ISO 20848‑3- Plug bung closure systems for plastics drums about? ISO 20848‑3 discusses plastic drums in packaging. ISO 20848‑3 is an international standard on plug-bung closure systems for plastics drums to ensure safe handling and transport of substances. ISO 20848‑3 is the third part of the ISO 20848 series on packaging plastic drums that specifies the characteristics and dimensions of plug/bung closure systems for internally threaded openings in plastics drums of nominal capacity 113,6 l to 220 l. ISO 20848‑3 specifies the requirements of closures for plastics drums which are of importance worldwide for the continued reuse of the drums during their life cycle. Who is ISO 20848‑3- Plug bung closure systems for plastics drums for ? ISO 20848‑3 on plug bung closure systems for plastics drums is useful for: Plastic drums manufacturers Plastic drums suppliers and dealers Testing laboratories/test personnel of plastic drums Packaging companies

Packaging. Plastics drums. Plug bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l

ASTM F3326-19 便携式燃料容器上火焰缓解装置的标准规范

Standard Specification for Flame Mitigation Devices on Portable Fuel Containers

KS T 1079-2018 金属板制口基及口盖

Metal caps and nozzles

KS T 1079-2018(2023) 金属帽和喷嘴

Metal caps and nozzles

ISO 20848-3:2018 包装 - 塑料桶 - 第3部分:用于塑料桶的堵​​塞系统 标称容量为113,6 l至220 l

This document specifies the characteristics and dimensions of plug/bung closure systems for internally threaded openings in plastics drums of nominal capacity 113,6 l to 220 l.

Packaging — Plastics drums — Part 3: Plug bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l

T/GZWL 007-2018 《生鲜果蔬周转筐及其使用标准》

4.1  规格尺寸 根据生鲜果蔬外形、质地、及周转筐循环使用需要，将周转筐分为两类：斜口型、折叠型。按核定外形尺寸分类。推荐外形见表1、2所示。 表1 斜口型周转筐规格尺寸 规格　规格尺寸（mm）　主要适用范围 　下口外径　上口外径　 1　460*305*250　515*355*260　体积较小且消费量不大、不耐挤压的果蔬，如：蓝莓、樱桃、黑莓、草莓等。 2　530*350*295　595*410*305　体积较小且消费量不大、较不耐挤压的果蔬，如：鲜枣、番茄、李子等。 3　610*405*325　680*470*340　大多数品种果蔬，如：猕猴桃、火龙果、马铃薯、白菜、芹菜等。 4　695*460*365　795*540*370　体积和重量较大且消费量大、耐挤压的果蔬，如：南瓜、马铃薯等 表2 折叠型周转筐规格尺寸 规格　规格尺寸（mm）　主要适用范围 　外径　内径　 1　530*410*180　530*380*170　体积较小且消费量不大、不耐挤压的果蔬。如：蓝莓、樱桃、黑莓、草莓等 2　530*410*240　530*380*230　体积较小且消费量不大、较不耐挤压的果蔬。如：鲜枣、李子、番茄等 3　600*400*180　560*370*160　体积较小且消费量不大、不耐挤压的果蔬。如：蓝莓、樱桃、黑莓、草莓等 4　600*400*230　560*370*220　体积较小且消费量不大、较不耐挤压的果蔬。如：鲜枣、番茄等 5　600*400*280　560*370*270　大多数品种果蔬。如：猕猴桃、火龙果、马铃薯、白菜、芹菜等 6　600*400*340　560*360*330　体积和重量较大且消费量大、耐挤压的果蔬，如：南瓜、马铃薯等 4.2基本要求 4.2.1 材质 符合GB/T 5737（食品塑料周转筐）要求，材质为高密度聚乙烯塑料，具有无毒、无异味、无刺激、无污染、耐水解、耐高低温和耐微生物性能。 4.2.2 外观 表面光滑完整平衡，无裂损，边沿及端手部位无毛刺，无明显白印、无明显色差，同一批产品色泽均匀一致，筐体各面具有网格式通风孔。 4.2.3 尺寸偏差 表3  周转筐尺寸偏差 项目　技术要求 偏差　按产品核定尺寸分段取相应的偏差率，采用累进法计算偏差 　400 mm以下部分　400 mm至600 mm部分 　±1.0％　±1.5％ 4.2.4质量偏差 不超过核定质量的-2.0~ 2.0%。 4.2.5物理、质量性能 周转筐质量还需满足以下要求，如表4所示： 表4   周转筐物理性能要求 项目　技术要求 表面黑点、杂质　筐体各面每500cm2面积中，长度0.5-2.0mm的黑点、杂质不多于5个，不得有长度大于2.0mm黑点、杂质。 箱底承重　筐底平面变形量不大于10 mm。 收缩变形率　筐体内对角线变化率不大于1.0%。 跌落性能　空筐从10 m 高跌落时不产生形变、裂纹。 堆码性能　叠加筐体高度时，使得筐体形变率不大于2.0%。 悬挂性能　筐体悬挂放置时，不允许产生裂纹。

Recycling containers use standards for fruits and vegetables

ASTM F670-02(2017) 罐 5和10-Gal（20和40-L）润滑油分配的标准规范

1.1 This specification covers the material, dimensions, and construction of 5 and 10-gal (20 and 40-L) tanks purchased to store and dispense lubricating oils. The tanks are industrial safety cans mounted on a T-bar bracket, complete with drip tray. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Tanks, 5 and 10-Gal (20 and 40-L) Lube Oil Dispensing

DB41/T 563-2017 道路运输液体危险货物罐式车辆金属常压罐体定期检验规程

Rules for Periodic Inspection of Metal Atmospheric Tanks of Tank Vehicles Transporting Liquid Dangerous Goods by Road

JIS Z 1601:2017 钢制紧口圆桶

Tight head steel drums

JIS Z 1604:2017 钢桶用塞子和法兰

Plugs and flanges for steel drums